Carrier 33AW-CS1 Manual de usuario

User interface Comfort™ Series

User Manual

User interface

Abbreviations / Meanings

Contents Page

NUI User Interface Comfort Series 33AW-CS1

CDU Compressor Device Unit

GMC Global Module controls

LWT Leaving water Temperature

EWT Enter water Temperature

TE Outdoor Heat Exchange Sensor

TD Discharge Temperature Sensor

OAT Outdoor Air Temperature

FR Mode Frequency Reduction Mode

Abbreviations / meanings .................................................... 2

Button Identication.............................................................. 3

On-screen Indicators.............................................................. 4

Quick Start................................................................................. 5

Setting the time and day........................................ 5

Changing the temperature.................................... 5

Keyboard Lock........................................................... 6

Programming the Control..................................................... 6

Touch‘N’Go feature ................................................. 6

Programming theTouch‘N’Go feature............... 6

To change the factory settings ............................. 7

Factory defaults for User Conguration............. 7

Changing the temperature time periods .......... 8

Assigning time periods to temperatures,

CDU mode & FR Mode............................................. 9

Advanced Programming Options ...................................... 11

UsingTouch‘N’Go buttons .................................... 11

To make a temporary change................................ 11

To hold it at home, away or sleep......................... 12

Advanced programming display codes............. 12

Changing your feature settings............................ 12

Features table............................................................ 13

Special Features....................................................................... 15

RoomTemperature Sensor Adjustment ............ 15

Shortcut to frequency reduction mode............. 15

What If ....................................................................................... 15

You get a system error message........................... 15

Fault Code Table........................................................ 16

Button Identication

ZONE Selects the Zone at which NUI is

present (Presently Not Using) AWAY Activates heating and cooling

settings for the away program

period

RUN/HOLD Holds the currently selected

temperature or runs the scheduled

program HOME Activates heating and cooling

settings for the home program

period

MODE Selects whether thermostat is set for

heating, cooling or o D/H/M

SET CLOCK Activates clock set mode

Increases the temperature or adjusts

the screen selection up when

setting advanced programming

features

START TIME Activates the programming menu,

displaying the six period start times

DOWN

Decreases the temperature or

adjusts the screen selection

down when setting advanced

programming features

PERIOD Activates the programming menu,

displaying the six programming

time periods

OK Saves settings when completing a

set-up or programming step DAYS

Activates the programming menu,

displaying the options – 1 to 7(all

days), 1 to 5 (weekdays), 6 to 7

(weekends) and individual day

(1,2,3,4,5,6,7)

SLEEP Activates heating and cooling

settings for the sleep program

period

English

On-Screen indicators

Sanitary Water System is using home

settings Schedule Activated

Gas boiler Not used Fahrenheit

System mode o System is using away

settings Home Antifreeze

Room air temperature Area Not used Celsius

Zone AM or PM indicator for

current time Auxiliary Heat Source

Not used System is using sleep

settings Solar

Cool Mode Service/Installer Mode Electric Heater

Time Display Area Relative humidity

Percentage Heat Pump

Outdoor temperature Not used Booster Sanitary Water

Day of the week Heat Mode Zone number

Alarm Keypad is locked (no

padlock means unlocked)

English

Quick Start

Setting the time and day

Changing the temperature

You must set the time and day before you can use any of the

NUI’s programming features.

Open the door1.

Press D/H/M SET CLOCK (2. ) button.

Press the up or down button, to change the hour.3.

Stop on the correct hour.

Press the D/H/M SET CLOCK (4. ) symbol button

again and the minutes will ash on the display.

Press the up or down button to change the minutes.5.

Stop on the correct number.

Press the D/H/M SET CLOCK (6. ) symbol button

again and day will ash on the display.

Press the up or down button to change the day.7.

Stop on the correct number.

Press OK button or close the door.8.

There are times when you want to change temporary

temperature. Here’s how.

Open the door1.

Press mode (M) button to select the desired mode.2.

Press up or down buttons on the right side until you

reach the desired temperature setting. This creates a

“temporary hold” until the next pre-set time period.

You will see schedule active icon

( ) ashing on the display.

To maintain that temperature setting so it doesn’t3.

change during the next pre-set time period, press

hold ( ) symbol button on the left side. The

temperature will stay at the setting you selected until

you release the hold. The schedule active icon ( )

will disappear.

To return the temperature to the pre-set level for that4.

time period, press hold ( ) symbol. This releases

the hold and the temperature will return to its

programmed level. The schedule active icon ( ) will

appear.

Close the door.5.

English

Quick Start

Programming the Control

Keyboard Lock

Touch‘N’ Go feature

Programming the Touch‘N’ Go feature

To Lock all key and block command functions

Open the door1.

Press and hold for 3 seconds the three buttons days2.

( ), period ( ) and start time ( ).

All the keys will be disabled and the lock icon (3. ) will

be visible on display.

To unlock the keyboard press again the three buttons4.

for 3 seconds. The lock icon ( ) will disappear.

The unique Touch‘N’Go feature on your thermostat is a

revolutionary tool that lets you use a simpler programming

option – literally, touch and go – to help you get the

maximum comfort control from the entire comfort system.

With the touch of one Touch ‘N’ Go button – home

( ), away ( ) and sleep ( )–you can tell

your thermostat where you’ll be. To keep the home at that

comfort level indenitely, you add one more button –hold

( ) – and you’re set. It’s the ideal choice for them whose

schedule varies from day to day or doesn’t t into the

two or four or six predictable time periods allowed by the

thermostat.

At the same time, these three comfort options – home, away

and sleep – are connected to the thermostat’s full-level

programming power so that you get the home comfort you

desire exactly when you want it.

The three Touch ‘N’ Go buttons are preset at the factory

for typical heating and cooling temperature settings and

assigned to specic time periods. You can change these

temperature settings and the hours you want to use them

easily. Learn how to do that and discover how useful this

device is as you read through this manual.

The Touch‘N’Go feature on your thermostat involves home

( ), away ( ) and sleep ( ) buttons

immediately under the display. They are used for three

programming options.

The simpler programming option requires you to either

accept the preset temperature settings for when you are

home, away or asleep, or to set your own Touch ‘N’ Go

heating and cooling temperature settings. Either way, your

home, away and sleep settings are automatically linked to

one of six time periods that are also preset (and changeable)

on the thermostat.

Here are the temperature settings that are pre-programmed

for your home, away and sleep periods.

Touch‘N’ Go Option Heat Cool

Home 20° C 24° C

Away 15° C 28° C

Sleep 18° C 26° C

English

Programming the Control

Use this blank grid to write down your required home

temperatures.

You’ll assign time periods to those temperatures later.

Touch‘N’ Go Option Heat Cool

Home

Away

Sleep

To change the factory settings

Factory defaults for User Conguration

Press and hold the comfort button1.

( ) to be changed for about ve

seconds. The set temperature along with the symbol

heat ( ) or cool ( ) will ash.

Press the up or down button on the right side of2.

the display until you reach the desired temperature

setting for the current mode of operation. At this

moment the triangle icon ( ) above the pressed

comfort button ( ) will start ashing.

To change the mode, press the mode (M) button3.

repeatedly until you see the required mode symbol

ashing on the screen.

Press the up or down button on the right side of4.

the display until you reach the desired temperature

setting.

Pressing one of the other two Touch 'N' Go button,5.

item 2 to 4 can be repeated.

Press OK button to conrm changes and exit from the6.

Comfort change mode.

Procedure for Changing the User Parameter settings to

Default values is given below.

Press simultaneously home (1. ) and away ( )

buttons at a time for 10 seconds to enter into the user

conguration mode. When this setting is rst selected,

999 will be displayed in the time display area and an

initial value of 10 will be displayed in the temperature

display area.

Press and hold the down button. When the counter2.

reaches zero, “Fd”will be displayed in the temperature

display area. This represents factory defaults are in

progress. Upon successful completion of restoring

defaults to EEPROM, the NUI will then force a reset.

English

Programming the Control

Changing the temperature time periods

After you have set temperature settings for home, away and

asleep, you can program the time of day you want to use for

those temperature settings.

The thermostat has six time ranges called periods. They are

identied on the display as P1, P2, P3, P4, P5 and P6.

The thermostat has preset periods (see below), but you can

change these to t your lifestyle.

What time blocks work for you? Write them in here and refer to this as you make the changes on the thermostat.

Period Period Start Time

P1 6:00 AM

P2 8:00 AM

P3 17:00 PM

P4 22:00 PM

P5 23:00 PM

P6 00:00 AM

Period Your Hours

Here’s how to change the factory-set time periods.

Open the door.1.

Press the days (2. ) button. You will see 1 to 7 ashing

on the display.

You must select one of these timeframe options – 1 to3.

7, 1 to 5, 6 to 7 or individual day (1, 2, 3, 4, 5, 6, 7) – by

pressing the days ( ) button again. You may also

make your selection by pressing the days ( ) button

again. (Select 1 to 7 if your individual day schedules

are same.)

When you have selected one of the options (1 to 7, 14.

to 5, 6 to 7 or individual day), press the period ( )

button. You will see P and a ashing 1 on the screen.

This is period 1 (P1), which begins at 6:00 AM.

To change the hours in P1, press the start time (5. )

button.

You will see the hours in 6:00 AM ashing on the6.

screen. Press the up or down button and stop on the

desired time.

English

Programming the Control

To change the minutes, press start time (7. )

button on the bottom of the screen again. You will

see the minutes in 6:00 AM ashing on the screen.

Press the up or down button and stop on the desired

time.

The“stop time”for period 1 (P1) is also the“start time”8.

for period 2 (P2). To change the stop time for P1 –

which means you are also changing the start time for

P2 – use the instructions in the next step to change

the start time for period 2.

To change the start time for period 2 (P2), press the9.

period button at the bottom of the screen twice. This

displays the information for period 2, with P2 ashing

on the display.

Similar way you can program P2, P3, P4, P5 and P6.10.

If you did not select 1 to 7 (all days) when you11.

started this process, repeat all the steps for your

remaining timeframe choice – 1 to 5 (weekdays), 6 to

7 (weekends) or individual day (1,2,3,4,5,6,7).

To conrm that the NUI has accepted your changes,12.

cycle through the six time periods by pressing days

(), selecting your time frame – 1 to 7 (all days), 1 to

5 (weekdays), 6 to 7 (weekends) or individual day –

and then pressing the period button to see the hours

assigned for each start time. Each time you press

period ( ) button, you will advance to the next

start time. If the program schedule is incorrect“- -“ is

displayed and all three arrows ( ) will be on..

Press OK or close the door.13.

Assigning time periods to temperatures, CDU mode & FR mode

Here’s an example of a programming would look using the factory-set periods and Touch ‘N’ Go options.

Pre-set Period

Start Time Period Number Pre-set Touch ‘N’Go

Option for Each Period CDU Mode Frequency

Reduction

6:00 AM 1 Home ( ) ON OFF

8:00 AM 2 Away ( ) ON OFF

5:00 PM 3 Home ( ) ON OFF

10:00 PM 4 Sleep ( ) ON OFF

11:00 PM 5 Home ( ) ON OFF

00:00 AM 6 Sleep ( ) ON OFF

Complete this schedule according to daily routine and use it as you follow the instructions below.

Pre-set Period

Start Time Period Number Pre-set Touch ‘N’Go

Option for Each Period CDU Mode Frequency

Reduction

English

Programming the Control

Here’s how to connect your six time periods with the three

comfort ranges – home, away and sleep, CDU Mode Settings

ON/OFF and Frequency Reduction mode settings ON/OFF.

Open the door.1.

Press the days (2. ) button at the bottom of the

thermostat. You will see 1 to 7 ashing on the display.

Select one of the options (1 to 7 , 1 to 5 , 6 to 7 or3.

individual day : 1, 2, 3, 4, 5, 6, 7) by pressing the days

( ) button until you get your desired option. Select

1 to 7 if your individual day schedules are same.

When you have selected one of the options (1 to 7, 14.

to 5, 6 to 7 or individual day: 1, 2, 3, 4, 5, 6, 7), press the

period ( ) button at the bottom of the thermostat.

P1 will ash on the display.

To change the hours in P1, press the start time (5. )

button at the bottom of the screen.

You will see the hours in 6:00 AM ashing on the6.

screen. Press the up or down button and stop on the

desired time.

To change the minutes, press start time (7. ) button.

You will see the minutes in 6:00 AM ashing on the

screen. Press the up or down button and stop on the

desired time.

The“stop time”for period 1 (P1) is also the“start time”8.

for period 2 (P2). To change the stop time for P1 –

which means you are also changing the start time for

P2 – use the instructions in the next step to change

the start time for period 2.

Press the Touch ‘N’ Go button – home (9. ), away

( ) or sleep ( ) – you want to use during

period 1 (P1) from the row of buttons just below the

display. You will see triangle icon ( ) above the

button selected. This tells the thermostat whether you

are home, away, or sleep during P1. The thermostat

will use the heating and cooling temperature settings

you’ve selected for that Touch ‘N’ Go button. For

example, if your heating temperature setting for

home is 23 °C, the thermostat will keep the heat at 23

during P1.

Press the zone (10. ) button on the left side of the

display.

If the previous CDU Mode status is ON ,the ot

(

) icon will appear on the display,

represents CDU mode is“OFF”,

If the previous CDU Mode status is OFF, thet

o (

) symbol will disappear from the

screen which represents CDU mode is ON

now.

Press the hold (11. ) button on the left side of the

display.

If the previous Frequency Reduction Modet

status is ON ,the ( ) icon will disappear from

English

Otros manuales para 33AW-CS1

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Termostato de Carrier

Carrier

Carrier 33CS Manual de usuario

Carrier

Carrier TSTATCCPSE01 Guía

Carrier

Carrier ComfortVu TBPL-24-H Instrucciones de funcionamiento

Carrier

Carrier Comfort Touch-n-Go Manual de usuario

Carrier

Carrier Comfort series Manual de usuario

Carrier

Carrier Infinity SYSTXCCWIC01-B Manual de usuario

Carrier

Carrier 53DFS250-SL Manual de usuario

Carrier

Carrier Touch-n-Go TC-PHP01-A Manual de usuario

Carrier

Carrier TP-WEM01 Manual de usuario

Carrier

Carrier 33CS Manual de usuario

Carrier

Carrier P/N 33CSSN2-MH Manual de usuario

Carrier

Carrier Edge TP-PRH Manual de usuario

Carrier

Carrier Performance Non-Programmable ADGE Manual de usuario

Carrier

Carrier TSTAT Instrucciones y recetas

Carrier

Carrier ComfortVu TB-24 Instrucciones de funcionamiento

Carrier

Carrier TSTAT Manual de usuario

Carrier

Carrier 33CS420-01 Manual de usuario

Carrier

Carrier 33AW-CS1 Manual de usuario

Carrier

Carrier XCT 7 40VCC727FQEE Manual de usuario

Carrier

Carrier 33CS Instrucciones y recetas

Carrier

Carrier TSTATCCPS701 Manual de usuario

Carrier

Carrier AQUAZONE 50QE900-250FS Manual de usuario

Carrier

Carrier TSTAT Manual de operación

Carrier

Carrier Debonair 33CS220-FS Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario

Honeywell

Honeywell T6811 Manual de usuario