Capetti Elettronica WSD10TII Manual de usuario

WSD10TII

User Manual

WSD10TII

User Manual

PAGE 2/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

1. Disclaimer.

•Specifications are subject to change without notice and should not be interpreted as any commitment on the part of Capetti Elettronica

S.r.l.

•Capetti Elettronica S.r.l. assumes no responsibility for any errors that may appear in this document. In no case Capetti Elettronica S.r.l.

will be liable for incidental or consequential damages resulting from the use of this document or the systems described in this

document.

•All Contents published or distributed by Capetti Elettronica S.r.l. are made available for general information purposes.

•It is not permitted to publish or use, in whole or in part, such contents for commercial purposes without the explicit written consent

of Capetti Elettronica S.r.l.

•The reproduction, duplication, modification, sale or resale of this material or part of it is not permitted without the explicit written

consent of Capetti Elettronica S.r.l.

2. General warnings.

•The following information must be read and understood before proceeding with the installation, commissioning and maintenance of

the devices described in this document.

•ATTENTION! Any omission or failure to follow these instructions scrupulously can cause danger.

•ATTENTION! Explosion hazard. In case of batteries substitution, make sure that the type is compatible and complies with the

specifications indicated by the manufacturer.

•In case of batteries substitution, DO NOT disconnect the flat cable which connect the electronic boards without removing batteries

before.

•ALWAYS substitute all the batteries, also in case of one single battery exhausted.

•If the device is powered by a fixed network, make sure you have disconnected the power supply before carrying out any type of

intervention. Failure to comply with this indication can cause damage to people and/or property.

•Follow the manufacturer's suggested warm-up time (

time required to obtain a reliable measurement

) of the transducer.

•Follow the manufacturer's suggested electric wiring of the transducer to measure (

ground shields at a single point, cable length and

section

); voltage measures on distances exceed 15/20 meters are subjected to electromagnetic disturbances. 0÷25mA inputs have a

superior electromagnetic compatibility (

EMC

•Avoid passage in cavities with power or high voltage cables.

•The protection and safety measures and the warranty provided by the Manufacturer with the equipment may be compromised if it’s

used in a manner that does not comply with this user manual.

•This equipment complies with CE regulations.

•Modifications or tampering not expressly approved by the Manufacturer could void the user's authorization to operate the equipment.

•This equipment must be installed by qualified personnel and in accordance with national regulations and/or related local requirements.

•Make sure that the object is properly fixed to supports/infrastructures capable of withstanding this load. Make sure proper methods

and materials are used when fixing the equipment to a wall.

•Only service personnel authorized by the manufacturer or personnel expressly authorized by the latter can open the container. There

are no user serviceable parts inside.

WSD10TII

User Manual

PAGE 3/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

3. Description.

The WSD10TII is a datalogger designed to measure 3 input channels to acquire outdoor temperature and inclination, with storage functionality

of samples acquired.

Inclination measurement is performed by a three-axis accelerometer, which allows the device free orientation related to the horizontal surface.

4. Thermometer: working logic.

The value contained in CH1 channel can be sampled every “

Threshold/Following interval

” as the

other channels.

5. Inclinometer: working logic.

a. Measure.

The datalogger furnishes X and Y axis values related to sampled movements after installation and

its position zeroing Such values are reported on channels CH2 and CH3 respectively.

If a value exceeds the maximum or minimum movement range, the measure will be declared as

“invalid”.

Normally these values are the result of a progressive average updated every “

Threshold/Following

interval

”recorded and sent to the gateway every “

Measure interval

”.

For the average to be done correctly, it is necessary that the “

Follower

” function, on CH2 and CH3 channels (active by default), must be enabled.

Otherwise, the average will be performed with the cadence of the "

Measure interval

The setup of these intervals is configurable and adjustable using

WineCapManager

software or cloud support.

b. Measure threshold.

Two thresholds for each inclination channel can be setup: two thresholds for CH2 and two thresholds for CH3.

Measure sample will be compared with thresholds values with interval obtained by “

Threshold/Following interval

” value.

c. Value following –Step answer.

Every “

Threshold/Following interval

” will be compared to the “

instant value

” (

average acquired in a time frame of 8 seconds

) with the current

sample.

If the deviation is greater than “

Delta increase

” value or less than “

Delta decrease

” value, configured in setup, measure is placed equal to the

“instant value” and the average initialized again to that value.

This event will be notified with recording and sending the new measure value.

Properly adjusting “

Delta

” values becomes possible manage movements and react to unexpected events without waiting for periods introduced

by average.

The device DOES NOT answer to SHOCK events and cannot be intended able to display dynamic events. An “

unexpected event

” must be

intended as a significant movement related to the quiet position of the device.

d. Installation position zeroing.

After fixing and installation operations, a “6+2” command (refer to

Picture 6 - Status table –Wireless mode

) can be issued which performs the

reset of inclination channels.

The command starts a first acquisition which defines the device’s absolute position and, consequently, the axis rotation to align internal

references. At the end of the procedure, the zero value and the axis position will be saved in memory to be recovered in case of device restart.

This procedure lasts around 5 minutes.

Picture 1 - Product image

WSD10TII

User Manual

PAGE 4/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

6. Default configurations.

Device default configurations at the first starting are the following:

•“

Measure interval

” = 60 minutes

•“

Threshold/Following interval

” = 5 minutes

•CH2 and CH3 “

Follower

” = Enabled with “

Delta Increase

” = 6° and “

Delta Decrease

” = 6°

Picture 2 - Device setup (using gateway)

Picture 3 - Channels/Axis correspondance

WSD10TII

User Manual

PAGE 5/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

7. Device pre-set and use mode.

a. Wireless Mode:

No setup operation is needed. Typically, the system is configured in factory, so the device is already associated to the system gateway. The

device is in STANDBY mode (

refer to Picture 5 - Command table

) for which is necessary to start it with the TEST command (

refer to 10 -

Installation procedure.

Otherwise, in case the device is in FACTORY RESET mode (

refer to Picture 5 - Command table

), that means it's ready for connecting to an

existing system, in order to associate it, make reference to the

“WineCap System - User Manual R30”

software manual. It is necessary to use

the

WineCapManager

software on the PC connected to the gateway that will be linked with the device.

8. Wireless device user interface.

The user interface consists of a “virtual” button that can be activated using the

WineCapKey

and of a two-colours led.

To give a command, user must approach the

WineCapKey

to the device’s sensible area and keep it in that position.; the following picture

(

Picture 4 - WineCapKey positioning

) shows device’s sensible points.

LED

WineCapKey

Picture 4 - WineCapKey positioning

WSD10TII

User Manual

PAGE 6/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

The following COMMAND table describes the available commands:

WIRELESS MODE COMMAND table

Flash count

Command

Description

1 flash

STATUS

Shows the device STATUS. As answer the led perform a flash sequence

as reported in the STATUS table. If the device is performing the TEST

(

refer to TEST command

) this command stops it.

2 flashes

TEST

Enter in TEST mode and transmits status and measurements every 5

seconds. If the device is in STANDBY mode or it is out of radio range,

this command forces the connection procedure to the WSN and the

return to the operative mode. The TEST stops after 120 seconds.

During TEST, the led continuously shows the STATUS to monitor the

received radio signal quality.

CAUTION: Measures acquired during TEST phase are NOT saved.

3 flashes

ENROL

Association to the network: must be used when the device has not yet

been included in a network, starts the entry and association procedure

to the gateway (

refer to “WineCap System - User Manual R30”

4 flashes

+ 4 flashes

STANDBY

Temporary device deactivation: the device is stopped. The sampling

process and the radio are/is. turned off losing the connection to the

network. To reactivate, a TEST command is necessary. The STANDBY

command must be given twice to confirm it: at the first sequence the

led flashes alternating RED and GREEN lights, waiting for the second

confirm sequence within 15 seconds. At the command execution the

led flashes as the STANDBY status (

refer to “Picture 6 - Status table –

Wireless mode”

5 flashes

+ 5 flashes

FACTORY RESET

The device performs the memory deleting procedure and goes in

STOP status. All samples, configuration and wireless network data

associated are LOST. To reactivate the device a new association and

configuration procedure is necessary (

ENROL command

). Also in this

case, the FACTORY RESET command must be given twice to confirm

it. At the command execution the led flashes as the

“PROBE/DATALOGGER NOT ASSOCIATED” status (

refer to “Picture 6 -

Status table –Wireless mode”

6 flashes

+ 2 flashes

CH2 AND CH3

ZEROING

The device performs the inclination channels X and Y axis zeroing

procedure, fixing the device’s absolute position and the consequent

AXIS ROTATION aligning the internal references and saving the ZERO

position.

6 flashes

+ 6 flashes

ZEROING

CANCELLATION

The device performs the cancellation procedure of zeroing operations

on channels 2 and 3. All the initial values are restored.

Picture 5 - Command table

WSD10TII

User Manual

PAGE 7/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

9. Device enrolment.

Not necessary if performed in factory before delivery.

Enrol the device to the wireless network (868MHz/915MHz) referring to the

“WineCap System - User Manual R30”

. In case the device is already

enCH2ed but in STANDBY status, a TEST command must be issued (refer to

Picture 5 - Command table

)

10. Installation procedure.

After installing the gateway in appropriate place in charge, (

refer to “WineCap System - User Manual R30

”), be sure that the device is enCH2ed

to the gateway and activated.

Head for the installation point. On the way, to check the quality of the radio coverage, use the "Field Measurer" function.

This function is activated issuing the TEST

(refer to Picture 5 - Command table)

command: position the

WineCapKey

in the spot indicated in

Picture 4 - WineCapKey positioning

and wait for two AMBER flashes, then remove the

WineCapKey

from device. The "Field Measurer" function

lasts enabled for two minutes.

To issue commands to the device, place the

WineCapKey

where indicated.

Once the

WineCapKey

, is detected, the led periodically emits AMBER flashes with a 2 second cadence.

For each flash, a different command is associated; to confirm the command the

WineCapKey

must be removed from the sensible area

immediately after the number of flashes corresponding at the desired command. The TEST corresponds to the second pulse and activate the

"Field Measurer" function.

The device will give back the radio signal quality through led flashes:

WIRELESS MODE STATUS Table

FLASH COUNT –WIRELESS MODE

STATUS/RADIO SIGNAL QUALITY

5 green flashes

ACTIVE - Radio signal: Excellent

4 green flashes

ACTIVE - Radio signal: Good

3 green flashes

ACTIVE - Radio signal: Fair

2 amber flashes

ACTIVE - Radio signal: Sufficient

1 red flash

ACTIVE - Radio signal: Insufficient

1 red flash 2” long

OUT OF RANGE

Network searching

2 red flashes 2” long

STANDBY

Radio off - No Logging

Short-long-short red

flashes series

FACTORY RESET

Device not enCH2ed –No logging

Picture 6 - Status table –Wireless mode

Optimize reception selecting the best position: small movements can help.

If the signal is absent or insufficient at the install point, a

repeater WR12

should be put between (

refer to “WineCap System - User Manual

R30

”). The

repeater WR12

itself must be in a position where the signal level is at least sufficient.

The network will reconfigure itself automatically; the signal will be good again when the device synchronizes with the

repeater WR12

The wireless communication will not be reconfigured until completely lost by the device. Because of this, in some cases it could be necessary

to force the operation. In such cases, put the device in STANDBY mode, then run the TEST again (

refer to “WineCap System - User Manual

R30

”).

NOTE: The display equipped datalogger

(WD04T)

is recommended, to verify the signal quality during devices installation.

WSD10TII

User Manual

PAGE 8/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

11. Shutting off/Reactivating the device.

If the device is shut off and left unused for a long time, you can issue the STANDBY command

(refer to Picture 5 - Command table)

. It

corresponds to the command number 4 and must be issued twice to confirm the operation.

Position the

WineCapKey

in the spot indicated in (

Picture 4 - WineCapKey positioning

), and wait for four AMBER flashes, then remove the

WineCapKey

from device. Verify that the device asks for confirmation of STANDBY command with alternate GREEN/RED flashing, then position

again the

WineCapKey

and wait for four flashes again. The device will confirm the STANDBY status lighting the RED led for 2 seconds twice. To

reactivate the device the TEST command must be issued.

WSD10TII

User Manual

PAGE 9/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

12. Technical Information

Power supply

19Ah - 3,6V type “D” lithium internal battery (

BAT3

)

Battery life (*)

Up to 5years

(samples every 60 minutes and radio signal quality at least

sufficient)

Measures acquired

(3 input channels)

•Temperature

•Biaxial inclination

Sampling interval

(*)

Selectable from one minute to 24 hours

(60 minutes default)

Datalogger capacity

64,000 samples (

for each channel

)

Working temperature

•Operative: -30°C ÷ +60°C

•Warehousing: -40°C ÷ +70°C

Radio frequency

ISM 868MHz

Radio coverage

Up to 6Km in line of sight

(can be extended using WR12 battery powered repeaters)

Sealing

IP68

Dimensions

150x150x60mm

Weight

990g

Case material

ABS, Galvanized iron bracket

Mounting

•4 holes - 9mm diameter

•Gluing using optional bracket

FIX-WSD10TII

•Magnetic using

FIX-MAG-WSD10TII

with 28Kg total traction

force

Connections

Wireless

Inclination –Transducer type

Three-axis accelerometer

Inclination –Measure range

+/-6,5000° in all the installation positions.

Automatic zeroing using command issued with

WineCapKey

Inclination –Measure resolution

0.0002°

Inclination –Repeatability

±0.0005°

Temperature - Transducer type

NTC10KΩ

Temperature - Measure range

-30°C ÷ +60°C

Temperature –Measure accuracy

•± 0,5°C Range -30°C ÷ 0°C

•± 0,2°C Range 0°C ÷ +60°C

Temperature - Measure resolution

0.01°C

* battery life may be influenced by fieldwork conditions, sampling/measuring interval and system configuration.

** radio coverage can be extended using up to 32 WR12 repeaters (maximum 16 for each path) between the device and the gateway.

WSD10TII

User Manual

PAGE 10/11

WA0425_WSD10TII_User Manual_R02 V6.0

www.capetti.it

13. Mechanical dimensions.

Picture 7 - Mechanical dimensions

Tabla de contenidos

Otros manuales de Registrador de datos de Capetti Elettronica

Capetti Elettronica

Capetti Elettronica WineCap WSD12-TT1K Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap WSD12-4D Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD00THCOP Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD15TIDR Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-LVD Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12PS-4AI Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD10DGII Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCapKey WSD02T-KK Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12-THEE Manual de usuario

Capetti Elettronica

Capetti Elettronica MWDG-GSM Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-VW Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-EVTT Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap WSD12-4D Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12-4VW Manual de usuario

Capetti Elettronica

Capetti Elettronica MWLI-MB Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap Lupo WSD15TIIDRO Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD02T-T1K Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12T-CO Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCapKey WSD12T-KK Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WLRD00TH Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD15IIDIST Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap WSD12-TT10KB1 Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-VW Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12T-IIDR Manual de usuario

Manuales populares de Registrador de datos de otras marcas

TESTO

TESTO 176 Manual de usuario

HT Italia

HT Italia XL421 Manual de usuario

HBM

HBM SOMAT XR CX22B-R Manual de usuario

Agtrix

Agtrix 380i Manual de usuario

Hobo

Hobo H8 Pro Manual de usuario

Beijing ART Tech

Beijing ART Tech PCI2320 Manual de usuario

Athena

Athena GET SL1 Manual de usuario

Motec Systems

Motec Systems C185 Manual de usuario

Beijing ART Tech

Beijing ART Tech USB2832 Manual de usuario

Rotronic

Rotronic HygroLog HL20 Manual de usuario

MRC

MRC DW-6092 Manual de usuario

Racelogic

Racelogic VBOX LapTimer Manual de usuario

Edu-Logger

Edu-Logger 900-240 Manual de usuario

Elma

Elma DT173 Manual de usuario

MadgeTech

MadgeTech PRTemp140 Hoja de especificaciones

Comet

Comet U0121M Manual de usuario

pico Technology

pico Technology PT-104 Manual de usuario

Soil Instruments

Soil Instruments GTecLink Manual de usuario