Capetti Elettronica WineCap WSD15IIDIST Manual de usuario

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

1. Description.

The WSD15IIDIST is a datalogger with 4 channels to acquire biaxial inclination, absolute distance, or temperature (selectable during

installation) and relative distance with storage functionality of samples acquired.

2. Inclinometer: operating logic.

a. Measure.

The datalogger provides the roll and pitch values relating to the displacements suffered after installation and the relative zeroing of

the position and reports them in the channels CH1 and CH2 respectively. If the value exceeds the maximum and minimum

displacement range, the measurement is declared "invalid".

Normally these values are the result of a progressive average updated at each "Threshold / Tracking time", recorded and sent to the

gateway at each "Measurement time". For the average to be carried out correctly, the “Follower” function on the pitch and roll

channel (active by default) must be enabled. Otherwise, the average will be performed with the cadence of the "Measurement

time".

The setting of these times is configurable and modifiable through the WineCapManager software or through the cloud.

b. Measure thresholds.

Two thresholds can be set for each slope measurement channel: two thresholds for rolling and two thresholds for pitching.

The value of the measurement will be compared with the values of these thresholds with a time interval obtained from the

“Threshold / Tracking time” value.

c. Value following –Step response.

At each “Threshold / Tracking time” the “instantaneous value” (average of the acquired values in a window lasting 8 seconds) will

be compared with the current measurement value.

If the difference is greater than the "Delta Increment" value or less than the "Delta Decrement" value, present in the settings, the

measurement is set equal to the "instantaneous value" and the average is reinitialized to that value.

This event will be notified with the recording and sending of the new measurement value.

Picture 1 - Product Image

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

By appropriately adjusting the “Delta” values, it is therefore possible to manage movements and react to sudden events without

waiting for the times introduced by the average.

The device does NOT respond to SHOCK events and cannot be intended for dynamic event displays. By "sudden event" is meant as

significant displacement related to the position of rest in which the instrument is working.

d. Reset installation position.

After installation and fixing, a "6 + 1" command can be issued (see Picture 3 - Commands table), which resets the channels dedicated

to the inclination.

The command starts a first acquisition which determines the absolute position of the tool and the consequent rotation of the axes

to align the internal references. At the end of the procedure, the zero value and the position of the axes are saved in the memory

so that they can be recovered in case of restart of the device.

This procedure takes about 5 minutes.

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

3. Distance meter: operating logic.

The laser pointer acquires the distance. The absolute distance is reported on CH3, while the distance relative to the reset position

is reported on channel CH4. If these values exceed the maximum and minimum displacement range, the measurement is declared

"invalid".

The distance is acquired with the frequency indicated by the “Measurement time” parameter. There are 2 thresholds per channel

which, if activated and configured, bring the acquisition cadence to the "Threshold / Tracking time" (default: disabled).

a. Reset installation position.

By giving the command "6+4" (see Picture 3 - Commands table), the channel dedicated to the measurement of the relative distance is

reset.

b. Laser pointer.

There is a "laser aiming" function: by giving the command "7" (see Picture 3 - Commands table) the laser is activated and allows a

precise aim at the target. This function ceases when a measurement is performed by the datalogger, or if command "7" is given

again.

It is recommended to use a white, non-glossy and possibly smooth material as a target.

4. Thermometer: operating logic.

The value reported on channel CH3 can be configured to provide the temperature acquired by the datalogger which is sampled at

each “Threshold / Tracking time” like the other channels.

To perform the configuration, it is necessary to connect the WSD15IIDIST datalogger to the PC via USB cable and use

WineCapManager. In the “Sensor→Properties” section, on the “Tools” page, it is possible to decide the behaviour of channel 3.

ATTENTION: after this modification it is necessary to enrol the datalogger with the gateway again.

5. Default settings.

The default settings of the device at first start-up are as follows:

•“Measurement time” = 60 minutes

•“Threshold / Tracking time” = 5 minutes

•CH1 e CH2 “Follower” = Active with “Delta Increment”= 6° and “Delta Decrement”= 6° values

•CH3 setup as ABSOLUTE DISTANCE

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

6. Device pre-set and use mode.

a. Wireless Mode:

No setup operation is needed. Typically, the system is configured from factory, so the device is already associated to the system

basestation. The device is in STANDBY mode (refer to Picture 4 - Status table - Radio signal quality) for which is necessary to start it

with the TEST command (refer to 9 - Installation procedure.).

Otherwise, in case the device is in FACTORY RESET mode (refer to Picture 4 - Status table - Radio signal quality), that means it's ready

for connecting to an existing system, in order to associate it, make reference to the “WineCap System - User Manual R30”

software manual. Is necessary to use the "WineCapManager" software on the PC connected to the basestation that will be

coupled with the device.

b. USB Logger Mode:

For this operation mode, stand-alone with data downloads through USB, the connection with the PC and the “WineCapManager”

running on it is necessary in order to modify the device 's operation mode. The sampling interval must be set with the device in

"STAND-ALONE" (refer to 7) mode and automatically, the device 's clock is aligned with the PC's clock, to assure the temporal

reference of the sample.

Sampling operations start may be selected disconnecting the USB cable or giving the proper command with the magnetic key.

(refer to 10 - Stand-alone USB datalogger installation.). More details on device 's connection/disconnection through the USB cable are

available on the WineCap System - User Manual R30 manual.

c. On field transition from USB to Wireless datalogger:

This transition is practicable in field, during the sampling period, using the wireless network association command. When the

association is done, the datalogger becomes a wireless datalogger and, besides sending new measures to the basestation, starts

a download process towards the same basestation of the measures acquired during the stand-alone period (refer to Picture 5 -

Stand-alone datalogger status).

7. Wireless device user interface.

The user interface consists of a “virtual” button that can be activated using the WineCapKey and of a two-colors led.

To give a command, user must approach the WineCapKey to the device’s sensible area and keep it in that position.; the following

picture (Picture 2 - WineCapKey positioning) shows device’s sensible points.

Picture 2 - WineCapKey positioning

LED

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

The following COMMAND table describes the available commands:

Flash count

Command

Description

1 flash

STATUS

Shows the device STATUS. As answer the led perform a flash sequence as reported

in the “STATUS” table. If the device is performing the TEST (refer to TEST command)

this command stops it.

2 flashes

TEST

Enter in TEST mode and transmits status and measurements every 5 seconds. If

the device is in STANDBY mode or it is out of radio range, this command forces the

connection procedure to the WSN and the return to the operative mode. The TEST

stops after 120 seconds. During TEST, the led continuously shows the STATUS to

monitor the received radio signal quality.

CAUTION: Measures acquired during TEST phase are NOT saved.

3 flashes

ENROLL

Association to the network: must be used when the device has not yet been

included in a network, starts the entry and association procedure to the

basestation (refer to “WineCap System - User Manual R30”).

4 flashes

+ 4 flashes

STANDBY

Temporary device deactivation: the device is stopped. The sampling process and

the radio are/is turned off losing the connection to the network. To reactivate, a

TEST command is necessary. The STANDBY command must be given twice to

confirm it: at the first sequence the led flashes alternating RED and GREEN lights,

waiting for the second confirm sequence within 15 seconds. At the command

execution the led flashes as the STANDBY status (refer to “WIRELESS MODE STATUS

Table”).

5 flashes

+ 5 flashes

FACTORY

RESET

The device performs the memory deleting procedure and goes in STOP status. All

samples, configuration and wireless network data associated are LOST. To

reactivate the device a new association and configuration procedure is necessary

(ENROLL command). Also in this case, the FACTORY RESET command must be given

twice to confirm it. At the command execution the led flashes as the

“PROBE/DATALOGGER NOT ASSOCIATED” status refer to “WIRELESS MODE STATUS

Table”).

5 flashes

+ 3 flashes

LOGGER

NO WSN

As the previous command but performs only the WSN deleting procedure and

disassociate from the basestation. The device enters in LOGGER STAND ALONE

mode: data are kept, and the sampling activity CONTINUES with previous setup.

Command must be given with 2 sequences: 5 flashes and then 3 flashes. At the

command execution wait for the device reboot. At the STATUS command,

“LOGGER” will be the answer (refer to “STAND-ALONE MODE STATUS Table”). A new

association (ENROLL command) is possible to a new basestation.

6 flashes

+ 1 flash

CH1 and CH2

Reset

The device carries out the procedure of zeroing the inclination channels of the X

and Y axes, determining the absolute position of the instrument and the

consequent ROTATION OF THE AXES, aligning the internal references and saving

the ZERO position.

6 flashes

+ 4 flashes

CH4

Reset

The device carries out the zeroing procedure of the relative distance acquisition

channel

6 flashes

+ 6 flashes

Cancellation

of resets

The device performs the procedure for cancelling all the zeroing operations carried

out on channels 1, 2 and 4. The initial values are restored.

7 flashes

Pointing

The laser pointer is turned on. To interrupt this phase, it is necessary to issue the

command again or wait for the next measurement.

Picture 3 - Commands table

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

8. Enrolling the device.

Not necessary if performed in factory before delivery.

Enroll the device to the network referring to the “WineCap System - User Manual R30”. In case the device is already enrolled but in

STANDBY status, a TEST command must be issued (refer to Picture 3 - Commands table).

9. Installation procedure.

After installing the basestation in appropriate place in charge, (refer to “WineCap System - User Manual R30”), be sure that the device is

enrolled to the basestation and activated.

Head for the environment to be monitored. On the way, to check the quality of the radio coverage, use the "Field Measurer" function.

This function is activated issuing the TEST (refer to Picture 3 - Commands table)command: position the WineCapKey in the spot indicated

in Picture 2 - WineCapKey positioning and wait for two AMBER flashes, then remove the WineCapKey from device. The "Field

Measurer" function lasts enabled for two minutes.

To issue commands to the device, place the WineCapKey where indicated.

Once the WineCapKey is detected, the led periodically emits AMBER flashes with a 2 second cadence.

For each flash, a different command is associated; to confirm the command the WineCapKey must be removed from the sensible

area immediately after the number of flashes corresponding at the desired command. The TEST corresponds to the second pulse and

activate the "Field Measurer" function.

The device will give back the radio signal quality through led flashes:

WIRELESS MODE STATUS Table

Flash count - Wireless mode

Status/Radio signal quality

5 green flashes

Excellent

4 green flashes

Good

3 green flashes

Fair

2 amber flashes

Sufficient

1 red flash

Insufficient

1 red flash 2” long

OUT OF RANGE

Network searching

2 red flashes 2” long

STANDBY

Short-long-short red

flashes series

FACTORY RESET

Device not enrolled

Optimize reception selecting the best position: small movements can help.

If the signal is absent or insufficient at the install point, a WR12 repeater should be put between (refer to “WineCap System - User Manual

R30”). The WR12 repeater itself must be in a position where the signal level is at least sufficient.

The network will reconfigure itself automatically; the signal will be good again when the device synchronizes with the WR12 repeater.

The link will not be reconfigured until completely lost by the device. Because of this, in some cases it could be necessary to force the

operation. In such cases, put the device in STANDBY mode, then run the TEST again (refer to “WineCap System - User Manual R30”).

NOTE: The display equipped datalogger (WD04T) is recommended, to verify the signal quality during devices installation.

Picture 4 - Status table - Radio signal quality

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

10. Stand-alone USB datalogger installation.

Install the datalogger in appropriate place.

If the sampling process has not yet been activated, you can start it through the WineCapKey.

Bring it closer to the sensitive point, wait for 2 flashes (TEST) (refer to Picture 3 - Commands table) and remove. The datalogger begins

sampling according to your settings through your PC.

Through the WineCapKey is possible to ask for the status, bring it close to the datalogger for 1 flash (STATE) and remove it.

STAND-ALONE MODE STATUS Table:

Flash count - Stand-alone mode

STATUS

1 green flash 2 seconds long

ACTIVE

2 red flashes 2 seconds long

STANDBY

Sequence of red flashes: short, 2

seconds long, short

FACTORY RESET

INVALID datalogger clock!

PC connection required

11. Shutting off/Reactivating the device.

If the device is shut off and left unused for a long time, you can issue the STANDBY command (refer to Picture 3 - Commands table). It

corresponds to the command number 4 and must be issued twice to confirm the operation.

Position the WineCapKey in the spot indicated in Picture 2 - WineCapKey positioning and wait for four AMBER flashes, then remove

the WineCapKey from device.

Verify that the device asks for confirmation of STANDBY command with alternate GREEN/RED flashing, then position again the

WineCapKey and wait for four flashes again. The device will confirm the STANDBY status lighting the RED led for 2 seconds twice.

To reactivate the device the TEST command must be issued.

Picture 5 - Stand-alone datalogger status

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

12. Technical Information.

Power supply

19Ah - 3,6V type “D” lithium internal battery

Battery life (*)

Up to 5years

(samples every 60 minutes and radio signal quality at least sufficient)

Measures acquired (4 input channels)

•Biaxial inclination

•Temperature

•Distance

Sampling interval (*)

Selectable from one minute to 24 hours (60 minutes default)

Datalogger capacity

64,000 samples (for each channel)

Working temperature

•Operative: -30°C ÷ +60°C

•Warehousing: -25°C ÷ +70°C

Radio frequency

ISM 868MHz

Radio coverage

Up to 6Km in line of sight

(can be extended using WR12 battery powered repeaters)

Sealing

IP65

Dimensions

100x100x80mm

Weight

1,6000g

Case material

Aluminium

Mounting

Using basic clamp or optional FIX-DIST clamp

(free adjustment on 2 axis)

Connections

Wireless, USB

Inclination - Transducer type

Three axis accelerometer

Inclination - Measure range

-6,5000° ÷ +6,5000°

Inclination - Measure accuracy

± 0.5% of measure

Inclination - Measure resolution

0.0002°

Temperature - Transducer type

NTC10KΩ

Temperature - Measure range

-30°C ÷ +60°C

Temperature - Measure accuracy

•± 0.5°C Range -30°C ÷ 0°C

•± 0.2°C Range 0°C ÷ +60°C

Temperature - Measure resolution

0.01°C

Relative distance–Transducer type

LASER distance meter

Relative distance –Measure range

+/-3.200mm

Relative distance –Measure resolution

0.1mm

Relative distance –Measure accuracy

±1mm

Relative distance –Repeatability

±0.3mm

Absolute distance –Transducer type

LASER distance meter

Absolute distance –Measure range

0÷65,000mm

Absolute distance –Measure resolution

1mm

Absolute distance –Measure accuracy

±1mm

Absolute distance –Repeatability

±0.3mm

LASER distance meter - Type

Class 2 - 655nm (visible red)

LASER distance meter –Sensor range

65,000mm (matte white target)

LASER distance meter –Temperature range

-10°C ÷ +50°C

LASER distance meter –Measure range

±3,200mm (at absolute distance of 65,000mm)

* battery life may be influenced by fieldwork conditions, sampling interval and system configuration.

** radio coverage can be extended using up to 32 WR12 repeaters (maximum 16 for each path) between the device and the basestation.

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

13. Mechanical dimensions.

14. Warnings.

•The protection and safety measures and the warranty provided by the Manufacturer with the equipment may

be compromised if it’s used in a manner that does not comply with this user manual.

•This equipment complies with CE regulations.

•This equipment can receive any interference which could also cause unwanted behaviour.

•Modifications or tampering not expressly approved by the Manufacturer could void the user's authorization to

operate the equipment.

•This equipment must be installed by qualified personnel.

•This equipment contains a Class 2 laser. The user should avoid pointing the laser directly into the eye while the

device is powered.

•The device has a weight of up to 1.6 kg. Make sure that the object is properly fixed to supports/infrastructures

capable of withstanding this load. Make sure proper methods and materials are used when fixing the

equipment to a wall.

•Only service personnel authorized by the manufacturer or personnel expressly authorized by the latter can

open the container. There are no user serviceable parts inside.

Picture 6 - Mechanical dimensions

WSD15IIDIST

User Manual

CAPETTI ELETTRONICA s.r.l. - Strada Stratta, 57

10090 CASTIGLIONE TORINESE - TORINO - ITALY

VAT 04837130014 - Phone 011.981.98.11 - Fax 011.981.98.210

e-mail [email protected] - web www.capetti.it

WA0416E_WSD15IIDIST_User Manual_R05

V5.0

15. Reference standards.

EN 61010 -1

For electromagnetic compatibility

EN 61000 - 3 - 2

EN 61000 - 3 - 3

EN 300 220 -2

EN 301 489 - 03

EN 61000 - 6 -1

This symbol indicates that this product is compliant with the European Directive 2011/65/CE that restricts

the use of substances in the manufacturing of electronic devices.

The “WEEE” logo on the label indicates that this product is compliant with the "WEEE" EC Directive. This

symbol (valid only in the European Union countries) indicates that the product it is applied to, MUST NOT

be discarded with ordinary household or industrial waste, but must be sent to an authorized reception

point. The end user should contact the device provider, either the manufacturer or the reseller, to agree a

collection and disposal process, after having checked the terms and conditions of sale.

The features shown may be subject to change without notice.

IT190200000111

Tabla de contenidos

Otros manuales de Registrador de datos de Capetti Elettronica

Capetti Elettronica

Capetti Elettronica Winecap Lupo WSD15TIIDRO Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD00THCOP Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD15TIIDR Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCapKey WSD02T-KK Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD15TIDR Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12-2DI Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCapKey WSD12T-KK Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap WSD12-4D Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12-4VW Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap WSD12-4D Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-VW Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD02T-T1K Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12-TT1K Manual de usuario

Capetti Elettronica

Capetti Elettronica MWLI-MB Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-LVD Manual de usuario

Capetti Elettronica

Capetti Elettronica MWDG-GSM Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-VW Manual de usuario

Capetti Elettronica

Capetti Elettronica Winecap WSD12-TT10KB1 Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12T-CO Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD00T Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD10DGII Manual de usuario

Capetti Elettronica

Capetti Elettronica WSD12-EVTT Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WSD12T-IIDR Manual de usuario

Capetti Elettronica

Capetti Elettronica WineCap WLRD00TH Manual de usuario

Manuales populares de Registrador de datos de otras marcas

TESTO

TESTO 176 Manual de usuario

HT Italia

HT Italia XL421 Manual de usuario

HBM

HBM SOMAT XR CX22B-R Manual de usuario

Agtrix

Agtrix 380i Manual de usuario

Hobo

Hobo H8 Pro Manual de usuario

Beijing ART Tech

Beijing ART Tech PCI2320 Manual de usuario

Athena

Athena GET SL1 Manual de usuario

Motec Systems

Motec Systems C185 Manual de usuario

Beijing ART Tech

Beijing ART Tech USB2832 Manual de usuario

Rotronic

Rotronic HygroLog HL20 Manual de usuario

MRC

MRC DW-6092 Manual de usuario

Racelogic

Racelogic VBOX LapTimer Manual de usuario

Edu-Logger

Edu-Logger 900-240 Manual de usuario

Elma

Elma DT173 Manual de usuario

MadgeTech

MadgeTech PRTemp140 Hoja de especificaciones

Comet

Comet U0121M Manual de usuario

pico Technology

pico Technology PT-104 Manual de usuario

Soil Instruments

Soil Instruments GTecLink Manual de usuario