Canon Super G3 FAX Board-AS Manual de usuario

SERVICE

MANUAL

June 18, 2018

Rev. 5

Super G3 FAX

Board-AS/AS2

Introduction

Important Notices

Application

This manual has been issued by Canon Inc. for qualified persons to learn technical theory, installation, maintenance, and repair

of products.

This manual covers all localities where the products are sold. For this reason, there may be information in this manual that does

not apply to your locality.

Corrections

This manual may contain technical inaccuracies or typographical errors due to improvements or changes in products.

When changes occur in applicable products or in the contents of this manual, Canon will release technical information as the

need arises. In the event of major changes in the contents of this manual over a long or short period, Canon will issue a new

edition of this manual.

The following paragraph does not apply to any countries where such provisions are inconsistent with local law.

Trademarks

The product names and company names used in this manual are the registered trademarks of the individual companies.

translated into another language, in whole or in part, without the consent of Canon Inc.

Caution

Use of this manual should be strictly supervised to avoid disclosure of confidential information.

Explanation of Symbols

The following symbols are used throughout this Service Manual.

Symbols Explanation Symbols Explanation

Check.

Remove the claw.

Check visually.

Insert the claw.

Check a sound. Push the part.

Introduction

Symbols Explanation Symbols Explanation

Disconnect the connector. Connect the power cable.

Connect the connector. Disconnect the power cable.

Remove the cable/wire from the

cable guide or wire saddle.

Turn on the power.

Install the cable/wire to the cable

guide or wire saddle.

Turn off the power.

Remove the screw.

Loosen the screw.

Install the screw.

Tighten the screw.

Cleaning is needed. Measurement is needed.

The following rules apply throughout this Service Manual:

1. Each chapter contains sections explaining the purpose of specific functions and the relationship between electrical and

mechanical systems with reference to the timing of operation.

In the diagrams, represents the path of mechanical drive; where a signal name accompanies the symbol, the arrow

indicates the direction of the electric signal.

The expression "turn on the power" means flipping on the power switch, closing the front door, and closing the delivery unit

door, which results in supplying the machine with power.

2. In the digital circuits, '1' is used to indicate that the voltage level of a given signal is "High", while '0' is used to indicate "Low".

(The voltage value, however, differs from circuit to circuit.) In addition, the asterisk (*) as in "DRMD*" indicates that the DRMD

signal goes on when '0'.

In practically all cases, the internal mechanisms of a microprocessor cannot be checked in the field. Therefore, the operations

of the microprocessors used in the machines are not discussed: they are explained in terms of from sensors to the input of

the DC controller PCB and from the output of the DC controller PCB to the loads.

The descriptions in this Service Manual are subject to change without notice for product improvement or other purposes, and

major changes will be communicated in the form of Service Information bulletins.

All service persons are expected to have a good understanding of the contents of this Service Manual and all relevant Service

Information bulletins and be able to identify and isolate faults in the machine.

Introduction

Contents

Safety Precautions...............................................................................................1

Notes Before it Works Serving............................................................................................................ 2

Points to Note at Cleaning...................................................................................................................2

Notes on Assembly/Disassembly........................................................................................................2

1. Product Overview.............................................................................................3

Specifications...................................................................................................................................... 4

2. Technical Explanation..................................................................................... 5

Basic Configuration............................................................................................................................. 6

Basic Construction................................................................................................................................ 6

Controls...............................................................................................................................................7

FAX communication control................................................................................................................... 7

3. Parts Replacement and Cleaning................................................................... 8

Parts List............................................................................................................................................. 9

PCBs................................................................................................................................................... 9

4. Error/Jam/Alarm............................................................................................. 10

How to View Fax Error Codes...........................................................................................................11

User error codes................................................................................................................................12

Service Error Code............................................................................................................................13

5. Service Mode.................................................................................................. 16

Overview........................................................................................................................................... 17

Configuration of the Service Mode........................................................................................................17

Operation method............................................................................................................................... 17

Menu List............................................................................................................................................19

Setting of Bit Switch (SSSW)............................................................................................................ 21

Bit Switch Composition........................................................................................................................21

Setting of Menu Switch (MENU)........................................................................................................33

Configuration of Menu Switches...........................................................................................................33

Setting of Numeric Parameter (NUMERIC Param.).......................................................................... 35

Configuration of Numeric Parameters................................................................................................... 35

Setting of Destination (TYPE)........................................................................................................... 38

Overview............................................................................................................................................ 38

Setting of Printer Functions (PRINTER)............................................................................................39

Setting of Bit Switch (SSSW)............................................................................................................... 39

Setting of Numeric Parameter (NUMERIC Param.)................................................................................40

IPFAX Setting....................................................................................................................................41

IPFAX................................................................................................................................................ 41

Initialization of Set Value (CLEAR)....................................................................................................42

Contents

Overview............................................................................................................................................ 42

Test Mode (TEST).............................................................................................................................43

Overview............................................................................................................................................ 43

MODEM Test......................................................................................................................................44

Function Test......................................................................................................................................46

Service Report (REPORT)................................................................................................................ 47

System Data List.................................................................................................................................47

System Dump List...............................................................................................................................47

Error Transmission Report...................................................................................................................49

6. Installation...................................................................................................... 50

How to Utilize This Installation Procedure.........................................................................................51

Symbols............................................................................................................................................. 51

Pre-checks........................................................................................................................................ 52

Product Name.....................................................................................................................................52

Points to Note at Installation.................................................................................................................52

Check Items When Turning OFF the Main Power..................................................................................52

Installation Outline Drawing................................................................................................................. 52

Checking the Contents......................................................................................................................53

Installation Procedure........................................................................................................................54

In the Case of iR-ADV 8500/6500 Series.............................................................................................. 54

In the Case of iR-ADV C5500 Series.................................................................................................... 57

In the Case of iR-ADV C7580/C7570/C7565 Series...............................................................................61

In the Case of iR-ADV 4500 Series.......................................................................................................64

Checking the Operation.....................................................................................................................68

Type Setting....................................................................................................................................... 68

Basic Setting.......................................................................................................................................68

FAX Communication Test.................................................................................................................... 68

Contents

Safety Precautions

Notes Before it Works Serving..............2

Points to Note at Cleaning.................... 2

Notes on Assembly/Disassembly..........2

Notes Before it Works Serving

• At servicing, be sure to turn off the power source according to the specified steps and disconnect the power plug.

• Do not turn off the power switch (of the host machine) when downloading is under way. Turning off the main power switch

while downloading is under way can disable the machine.

Points to Note at Cleaning

When performing cleaning using organic solvent such as alcohol, be sure to check that the component of solvent is vaporized

completely before assembling.

Notes on Assembly/Disassembly

Follow the items below to assemble/disassemble the device.

1. Disconnect the power plug to avoid any potential dangers during assembling/disassembling works.

2. If not specially instructed, reverse the order of disassembly to reinstall.

3. Ensure to use the right screw type (length, diameter, etc.) at the right position when assembling.

4. To keep electric conduction, binding screws with washers are used to attach the grounding wire and the varistor. Ensure to

use the right screw type when assembling.

5. Unless it is specially needed, do not operate the device with some parts removed.

6. Never remove the paint-locked screws when disassembling.

CAUTION:

English

CAUTION

The fuse may be in the neutral, and that the mains shall be disconnected to de-energize the phase conductors.

German

VORSICHT

Die Sicherung kann sich im Nullleiter befinden und das Hauptnetz muss abgetrennt werden, um die Phasenleiter

stromlos zu machen.

Safety Precautions

Product Overview

1Specifications........................................4

Specifications

Following is a specification list.

Item Description

Communication G3

Line type Public Switched Telephone Network

Modulation <G3 image signal>

ITU-T V.27ter (2.4 Kbps, 4.8 Kbps)

ITU-T V.29 (7.2 Kbps, 9.6 Kbps)

ITU-T V.17 (TC 7.2 Kbps, TC 9.6 Kbps, 12 Kbps, 14.4 Kbps)

ITU-T V.34 (2.4 Kbps, 4.8 Kbps, 7.2 Kbps, 9.6 Kbps, 12 Kbps, 14.4

Kbps, 16.8 Kbps, 19.2 Kbps, 21.6 Kbps, 24 Kbps, 26.4 Kbps, 28.8

Kbps, 31.2 Kbps, 33.6 Kbps)

ITU-T V.21 No.2 (300 bps)

ITU-T V.8, V.34 (300 bps)

Transmission speed 33.6 Kbps, 31.2 Kbps, 28.8 Kbps, 23.4 Kbps, 24 Kbps, 21.6 Kbps,

19.2 Kbps, 16.8 Kbps, 14.4 Kbps, 12 Kbps, TC 9.6 Kbps, TC7.2

Kbps, 9.6 Kbps, 7.2 Kbps, 4.8 Kbps, 2.4 Kbps

auto fallback function

Coding method JBIG, MMR, MR, MH

G3-specific abridged procedure no

Dial tone detection yes

Modem IC Modem supporting V.34 standard

Error correction ITU-T ECM

Transmission original size A3, A4, A4R, A5, A5R, B4, B5, B5R, LTR, LTRR, LGL, 11x17,

STMT, STMTR

ADF: double-sided originals accepted

Scanning line density Normal: 8 pels*2/mm x 3.85 line/mm

Fine: 8 pels*2/mm x 7.7 line/mm

Super-Fine: 8 pels*2/mm x 15.4 line/mm

Ultra-Fine: 16 pels*2/mm x 15.4 line/mm

Halftone 256 gradations

Recording unit maximum reception size: A3 (297 mm x 420 mm)

scanning line density: 600 dpi x 600 dpi

Memory image memory (Canon Fax Standard Chart No.1): Approx. 6000

prints

memory type: Hard disk

storage: JBIG

Extension telephone connection yes

Answering machine connection no

Fax/Tel switch-over yes

Quick Direct Transmission yes

Transmission Header

(Add Remote Name on Header SW)

yes

Remote reception yes

Polling (F code) no

Memory box yes

Password reception yes

Machine telephone No. transmission yes

User abbreviation transmission yes

Auto Dial Function Address Book: 1,800 destinations

(including destinations stored in one-touch buttons)

Broadcasting 256 targets (maximum number of targets)

maximum number of targets by 10 key dialing: 64 target

1. Product Overview

Technical

Explanation

Basic Configuration...............................6

Controls.................................................7

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Accesorios de impresora de Canon

Canon

Canon Inner Finisher Additional Tray-A1 Manual de operación y mantenimiento

Canon

Canon DADF-AV1 Manual de usuario

Canon

Canon iR-ADV Security Kit-B1 Manual de usuario

Canon

Canon Finisher-U1 Manual de servicio

Canon

Canon Cassette Module-AE1 Manual de usuario

Canon

Canon Finisher-R1 Manual de usuario

Canon

Canon Duplex Color B1 Manual de usuario

Canon

Canon Two-Knife Booklet Trimmer-A1 Manual de usuario

Canon

Canon Shift Tray-E1 Manual de usuario

Canon

Canon Color iR Security Kit-A1P Manual de usuario

Canon

Canon Duplex Unit-A1 Manual de servicio

Canon

Canon Super G3 3rd Line FAX Board-AE1 Manual de usuario

Canon

Canon Stacker-C1 Manual de usuario

Canon

Canon PH-72 Manual de usuario

Canon

Canon Two-Knife Booklet Trimmer-A1 Manual de usuario

Canon

Canon iR Security Kit-A2 Manual de operación y mantenimiento

Canon

Canon RU-61 Manual de usuario

Canon

Canon USB Application Interface Board-D1 Manual de usuario

Canon

Canon Cassette Feeding Unit-AM1 Manual de usuario

Canon

Canon Finisher-R1 Manual de operación y mantenimiento

Canon

Canon DU7-1101-000 Manual de usuario

Canon

Canon Finisher-U1 Manual de usuario

Canon

Canon FY8-13HR-000 Manual de usuario

Canon

Canon ZDJ-S01 Manual de usuario

Manuales populares de Accesorios de impresora de otras marcas

Star Micronics

Star Micronics TSP800 Series Manual de usuario

REA

REA JET HR pro 2K Manual de usuario

HP Laserjet,Color Laserjet 4si Manual de usuario

oliser

oliser MS 45 Manual de usuario

Roland

Roland DU2-64 Instrucciones y recetas

Xerox

Xerox EFI EXP6000 Manual de usuario

Sharp

Sharp FO-1MK Manual de usuario

Labelmate

Labelmate PM-300 Manual de usuario

Epson

Epson T6248 Manual de funcionamiento

Epson

Epson OT-BZ20 Manual de usuario

Ricoh

Ricoh LCIT RT5100 Guía de inicio rápido

GBC

GBC 16 Series Manual de usuario

Develop

Develop SD-509 Manual de usuario

Kyocera

Kyocera KM-6230 Manual

Triumph Adler

Triumph Adler DF-710 Manual

Citizen

Citizen CBM-202PC Series Manual de usuario

Codonics

Codonics Virtua 1VCX-LR833 Guía de referencia

TonerRefillKits

TonerRefillKits ReChargX RX126 Manual de usuario