Canon Inner Finisher-D1 Manual de operación y mantenimiento
ENGLISH 日本語
ENGLISH 日本語
Finisher-D1 with Inner 2/3 Hole Puncher-A1 Installation
Procedure
Follow the instructions herein when installing the equipment to its host machine.
PRINTED IN CHINA PUB No. FT1-0627-000
2
2
Confrmation of the Footprint
Confrmation of the Footprint
How to Utilize This Installation Procedure
When using the parts included in the package
A symbol is described on the illustration in the case of using the parts included in the package
of this product.
Symbols in the Illustration
F-1-1
F-1-2
Confrmation of the Footprint
The following is the footprint condition for the installation and maintenance.
Inner Finisher-D1 and Inner 2H Puncher-A1
500 mm or more
Inner Finisher-D1 with Inner 2/3 Hole Puncher-A1
F-1-3
3
3
Turning OFF the Power of the Host Machine
Turning OFF the Power of the Host Machine
Notes Before Installation
CAUTION:
In case the 3 Way Unit-C1 is about to be installed in the host machine besides the
Inner Finisher-C1, install the 3 Way Unit-C1 prior to the installation of the Inner
Finisher-C1.Refer to the installation procedure of the 3 Way Unit-C1.Install the
Additional Tray-A1 prior to the installation of the Inner Finisher-C1.Refer to the
installation procedure of the Additional Tray-A1 .
1. When the Additional Tray-A1 is installed to the Inner Finisher-D1, install the
Additional Tray-A1 prior to the installation of the Inner Finisher-D1. Refer to the
installation procedure of the Additional Tray-A1.
2. In case the USB Device Port-D1 is about to be installed in the host machine
besides the Inner Finisher-D1, install the USB Device Port-D1 prior to the
installation of the Inner Finisher-D1. Refer to the installation procedure of the USB
Device Port-D1.
Turning OFF the Power of the Host Machine
Conf rm that the electrical power is OFF before installation.
1) Turn the main power switch of the host machine OFF.
2) Conf rm that the control panel display and the main power lamp have gone OFF and
unplug the host machine.
4
4
Checking the Contents > Included Items of Inner Finisher-D1 with Inner 2/3 Hole Puncher-A1
Checking the Contents > Included Items of Inner Finisher-D1 with Inner 2/3 Hole Puncher-A1
Checking the Contents
Unpack the Inner Finisher-D1 with Inner 2/3 Hole Puncher-A1 and make sure that none of the following parts is missing.
Included Items of Inner Finisher-D1 with Inner 2/3 Hole Puncher-A1
[1] [2] [3]
[4]
[7]
[14]
[15]
[12][11]
[10]
[16]
[5]
[6]
[17]
[8]
[9]
[13]
[1] Inner Finisher 1 pc.
[2] Staple sheet 1 box (3pcs.)
[3] Staple cartridge 1 pc.
[4] Fixing plate 1 pc.
[5] Eddge saddle 1 pc.
[6] Punch unit 1 pc.
[7] Tray lower cover 1 pc.
[8] Blindfold label (white) 1 pc.
[9] Finisher front cover 1 pc.
[10] Operation sub cover 1 pc.
[11] Rail unit 1 pc.
[12] Path guide 1 pc.
* [13] Motor cover (OP) 1 pc.
[14] Cover hinge mount 1 pc.
[15] Cable cover 1 pc.
[16] Rail support (f) 1 pc.
[17] Screw (RS tightening; M3x8) 15 pcs.
* Motor cover(OP) is used only when the additional tray is
equipped with the innner fnisher.
T-1-1
F-1-4
5
5
Installation Procedure > Preparation at the Host Machine
Installation Procedure > Preparation at the Host Machine
Installation Procedure
Preparation at the Host Machine
1) Open the right cover of the host machine.
2) Open the delivery guide.
• 1 screw (Removed screw is no longer reused.)
x1
F-1-5
3) Remove the support cover.
• 2 screws
• 2 hooks
x2
x2
4) Remove the support cover (left).
(Removed support cover (left) is no longer reused.)
• 3 hooks
x3
F-1-6
F-1-7
6
6
Installation Procedure > Preparation at the Host Machine
Installation Procedure > Preparation at the Host Machine
5) Open the front cover of the host machine.
6) Open the toner supply cover.
7) Remove the screw and manipulate the left cover to remove the inner cover.
(Removed inner cover is no longer reused. )
• 1 screw
• 3 hooks
x1
F-1-8
F-1-9
8) Remove the delivery rear cover (upper/lower) and the delivery tray.
(Removed delivery rear covers, delivery tray and screws are no longer reused.)
• 2 screws
x1
x1
9) Remove the delivery positioning guide.
(Removed delivery positioning guide and screw are no longer reused.)
• 1 screws
x1
F-1-10
F-1-11
7
7
Installation Procedure > Preparation at the Host Machine
Installation Procedure > Preparation at the Host Machine
10)Lift up the sensor ag (for the delivery tray 1 full detection) as shown in the gure and
remove it.
(Removed sensor ag is no longer reused.)
11) Remove the sensor ag holder.
(Removed sensor ag holder is no longer reused.)
• 1 hook
F-1-12
F-1-13
12) Remove the sensor ag (for the delivery tray 2 full detection) if there is.
(Removed sensor ag is no longer reused.)
NOTE:
Bend the sensor ag and dismount its shaft at the front end. Then remove the
shaft downward at the rear end.
F-1-14
8
8
Installation Procedure > Installing the Punch Unit in the Host Machine
Installation Procedure > Installing the Punch Unit in the Host Machine
Installing the Punch Unit in the Host Machine
1) Hold the parts as instructed in the gure and take the punch unit out of the carton box.
2) Remove all the shipping tapes and the packing materials for transport.
3) Remove the punch front cover.
• 2 screws
x2
F-1-15
F-1-16
4) Remove the sliding xture. (Removed sliding xture and screws are no longer reused.)
• 2 screws
x2
5) Install the punch front cover removed at the step 3) in the punch unit.
• 2 screws removed at the step 3)
x2
F-1-17
F-1-18
9
9
Installation Procedure > Installing the Punch Unit in the Host Machine
Installation Procedure > Installing the Punch Unit in the Host Machine
6) Hold the parts as instructed in the gure and set the punch unit in the host machine.
CAUTION:
Pay attention that the punch cable harness should not be caught in hardwareand
release the harness towards the main power switch.
F-1-19
7) Fix the punch unit to the host machine.
• 1 screw (RS Tightening; M3x8)
x1
8) Attach the xing plate included in the inner nisher carton to the punch unit.
• 1 screw (RS Tightening; M3x8)
x1
NOTE:
The xing plate comes behind the front frame of the punch unit.
(Internal thread is in the xing plate.)
F-1-20
F-1-21
10
10
Installation Procedure > Installing the Inner Finisher in the Host Machine
Installation Procedure > Installing the Inner Finisher in the Host Machine
9) Attach the eddge saddle at frame edge as shown and put the punch cable harness in the
saddle.
NOTE:
Do not use another wire saddle provided in the same plate as it is used for the other
optional equipment.
F-1-22
Installing the Inner Finisher in the Host Machine
1)Fix the rail unit
• Front: 2 screws (RS Tightening; M3x8)
• Rear: 2 screws (Screw with washer, already set on the rail unit)
NOTE:
Position of the rail unit is xed by 3 points at rear side.
2 screws with washer are already set at rear side of the rail unit.
Fix the rail unit to the rear frame in the condition with washers.
x4
Screw with washer
F-1-23
Otros manuales para Inner Finisher-D1
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Accesorios de impresora de Canon
Canon
Canon AD2 Manual de usuario
Canon
Canon imagePROGRAF iPF830 Manual de usuario
Canon
Canon Finisher-U1 Manual de servicio
Canon
Canon DADF-AV1 Manual de usuario
Canon
Canon NP6218 Cómo utilizar
Canon
Canon IP 1500 Manual de usuario
Canon
Canon Multi Function Professional Puncher-A1 Manual de operación y mantenimiento
Canon
Canon P1-DTSII Manual de usuario
Canon
Canon Puncher Unit-P1 Manual de usuario
Canon
Canon Inner Finisher Additional Tray-A1 Manual de operación y mantenimiento
Canon
Canon DADF-N1 Manual de usuario
Canon
Canon Finisher-Q1 Manual de usuario
Canon
Canon RU-61 Manual de usuario
Canon
Canon Saddle Finisher-T2 Manual de servicio
Canon
Canon Inner 2 Way Tray-E1 Manual de usuario
Canon
Canon iR1200 Series Manual de operación y mantenimiento
Canon
Canon Paper Deck Unit-B1 Manual de usuario
Canon
Canon DADF-P1 Manual de usuario
Canon
Canon Additional Finisher Tray-C1 Manual de usuario
Canon
Canon INNER 2-WAY TRAY-E1 Manual de operación y mantenimiento
