Canon PowerShot SD430 DIGITAL ELPH WIRELESS Manual de usuario

Canon Digital Camera

User Guide for Camera-to-Camera Data Transfer

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Transferring Images via a Wireless Connection . . . . . . . . 2

Registering Your Camera Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Registering Target Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Connecting Cameras via a Wireless Connection . . . . . . . . . . . . . . . . . . 3

Transferring Images One by One . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Transferring Ordered Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Ending the Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Trademark Acknowledgments . . . . . . . . . . . . . . . . . . . . . . 6

Introduction

If you upgrade the firmware of your PowerShot SD430 DIGITAL ELPH WIRELESS/DIGITAL

IXUS WIRELESS camera, it will be possible to transfer images between cameras* via a wireless

connection without using a PC.

This guide will explain procedures for transferring images via a wireless connection. For

guidance in the use of the camera, safety precautions and radio wave warning, please refer to

the Camera User Guide.

* Image transfer is only possible between PowerShot SD430 DIGITAL ELPH WIRELESS/DIGITAL IXUS WIRELESS cameras

with upgraded firmware.

* Images are transferred from one camera to another camera. Images cannot be transferred between more than 2 cameras.

Transferring Images via a Wireless Connectio

First, select a name for your camera and register it.

zYou must follow the following procedures for both your own and the target camera.

Registering Your Camera Name

1Slide the mode switch to (Playback)

(Wireless) Menu [Set Camera Name]

zRefer to the Camera User Guide for your camera for details on

Menu operation.

2Set up name and press .

zYou can set up the camera name with up to 5 letters. Select let-

ters using the or button, and press the or button to

move forward or backward. Capital letters and numbers can be

used for the camera name.

zThe default setting is [AAAAA].

zIf you do not wish to register a name, press the MENU button.

Registering Target Camera

1Slide the mode switch to (Playback)

(Wireless) Menu [Reg. Target Device]

2Select [Camera] for target device and press .

Make sure that your camera displays your camera’s

name and that the target camera displays its camera

name and press the on both cameras simulta-

neously (within approximately 10 seconds).

This step connects your camera to the target camera and registers

each camera's name in the other camera as a target device.

zWhen the wireless connection starts, the wireless lamp will begin to blink blue.

When you wish to change the name, follow Step 2 in Registering Your Camera Name (p. 2).

Connect your camera to the registered target camera via wireless.

zYou must follow the following procedures for both your and the target camera.

zWireless connection is not possible without memory cards inserted in the cameras.

4When the name of the target camera and [Registration completed]

are displayed, press .

zIf the name is already registered, [Already registered] will be displayed.

zIf you have failed to register, go back to Step 1 and repeat the procedure.

Connecting Cameras via a Wireless Connection

1Slide the mode switch to (Playback)

(Wireless) Menu [Connect/Disconnect]

zIf you press the button without displaying the Menu in the

playback mode for both cameras simultaneously (within

approximately 30 seconds), the wireless connection will start.

After confirming that the name of the target camera

is selected as the [Target Device], select [Connect]

and press the (or ) for both cameras simulta-

neously (within approximately 30 seconds).

zWireless connection will start and wireless lamp and but-

ton will both blink blue. If you press the FUNC./SET button while

the light is blinking, the connection will be canceled.

zWhen the connection has been completed, the camera’s wireless lamp and the but-

ton will remain on (without blinking), and the icon will be displayed on the playback

screen, showing the connection’s signal strength.

zIf a camera name other than the one you would like to connect to is displayed as the tar-

get device, use the button to select the [Target Device], and then select the camera of

your choice with or button.

Changing the Wireless Channel

If the channel (useful frequency) is already in use by another device, change the

channel on one of the cameras making the wireless connection to avoid interference

from radio waves. Channel changes on one camera will automatically be reflected on

the other camera.

1Select [Target Device], confirm that the

name of the target camera is displayed

and press .

2Use the or button to change the channel and press .

zPress the MENU button to return to Step 1 without changing the channel.

You can transfer images one by one to a target camera connected via a wireless connection.

zImages can be transferred during index playback.

zReceived images will be stored at the end of all image files.

You may transfer multiple images at the same time to a target camera connected via wireless.

For instructions on how to designate the transfer order, please refer to the Camera User Guide

(Advanced): Setting the DPOF Transfer Settings (p. 91). The explanation given here is the

procedure to transfer the ordered images.

Transferring Images One by One

1Confirm that the cameras are connected via a wireless connection.

zFor instructions on how to connect the cameras via a wireless connection, please refer to

Connecting Cameras via a Wireless Connection (p. 3).

2Select the image you would like to transfer from

your camera and press the button.

zYou may transfer an image by pressing the FUNC./SET button

instead of . In such a case, in the next screen select [Trans-

fer] with the or button, and press the FUNC./SET button

once again.

zThe transfer will begin. The wireless lamp and the button

will blink blue.

zThe transferring camera will display [Transferring] and the receiving camera will display

[Receiving]. When the transfer is complete, [Transfer completed] and [File(s) received] will

be displayed.

zIf you wish to cancel the operation while transferring, press the FUNC./SET button while

[Transferring] is displayed on the screen.

zIf you have failed to receive, [File(s) not received] will be displayed. Press the FUNC./SET

button, and the screen will return to the previous screen.

zIt is not possible to transfer movies or sound memos.

zTwo cameras cannot transfer images at the same time (If one is transferring, the other

camera may only receive).

zThe camera receiving the images cannot cancel while receiving.

Transferring Ordered Images

1Confirm that the cameras are connected via a wireless connection.

zTo make the wireless connection, refer to Connecting Cameras via a Wireless Connection

(p. 3).

2Press on the camera transferring the images

and select [ (Transfer Order)] from [ (Play)

Menu].

zFor details on the Menu operation, please refer to the Camera

User Guide (Advanced).

zReceived images will be stored at the end of all image files.

The wireless connection can be terminated by the following steps.

zEnding from (Wireless) Menu (See below).

zTurn off the power or switch over to Shooting Mode

End with (Wireless) Menu

Select [Transfer] and press .

If you have not selected the images for transfer order in advance,

specify the images with [Order] or [Mark all] and select [Transfer].

zTransfer of images will begin. The wireless lamp and the

button will blink blue.

The transferring camera will display [Transferring] and the receiving

camera will display [Receiving]. When the transfer is complete, [Transfer completed] and

[File(s) received] will display.

zIf you wish to cancel the operation while transferring, press the FUNC./SET button while

[Transferring] is displayed on the screen.

zIf you have failed to receive, [File(s) not received] will be displayed. Press the FUNC./SET

button, and the screen will return to the previous screen.

zIt is not possible to transfer movies or sound memos.

zTwo cameras cannot transfer images at the same time (If one is transferring, the other

camera may only receive).

zThe camera receiving the images cannot cancel while receiving.

Ending the Wireless Connection

1(Wireless) Menu [Connect/Disconnect]

2Make sure the name of the camera is displayed as [Target Device],

then select [Disconnect] and press .

zThe wireless connection will end and [Disconnected] will appear

on the target camera screen. Press the FUNC./SET button and

the Playback screen will appear.

Troubleshooting

Camera cannot be registered or wireless connection cannot be selected.

Camera is in shooting mode zChange to Playback mode

Unable to register the target camera in your camera.

Registration limit exceeded in [Target

Device]

zA maximum of 7 new target devices can be

registered in [Target Device]. If you wish to

Registration] to delete target devices you no

longer use. For instructions on how to delete

target devices refer to the Camera User Guide

(Advanced): Deleting Target Devices (p. 104).

The wireless connection has become

weak

zDo not use near a microwave oven or any other

device that emits radio waves.

zDo not place the two cameras far apart.

zDo not place anything between the two cameras.

Unable to transfer images.

There is no free space left in the

memory card of the receiving camera.

zInsert a new memory card.

zIf required, download the images to a computer

and erase them from the memory card to make

space.

The SD memory card is write-protected. zSlide the write protect tab of the SD memory card

upward.

Menu, Delete, Jump or Movie Playback

screen is displayed on the receiving

camera.

zDisplay the still image playback screen.

Wireless connection is disconnected.

The wireless connection has become

weak.

zDo not use near a microwave oven or any other

device that emits radio waves.

zDo not place the two cameras far apart.

zDo not place anything between the two cameras.

When a large volume of images (around

1000) is stored in the memory card, it

may not be possible to establish a

wireless connection.

zDownload necessary images from the memory

card to a computer and erase them from the

memory card to make space.

Trademark Acknowledgments

zThe SD Logo is a trademark.

zOther names and products not mentioned above may be registered trademarks or

trademarks of their respective companies.

Otros manuales para PowerShot SD430 DIGITAL ELPH WIRELESS

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara digital de Canon

Canon

Canon RebelT3i EOS 600D Manual de usuario

Canon

Canon PowerShot SX130 IS Manual de usuario

Canon

Canon EOS 5D Mark II - EOS 5D Mark II 21.1MP Full Frame CMOS Digital SLR... Manual de usuario

Canon

Canon PowerShot A550 Manual de usuario

Canon

Canon EOS 5D Mark II Manual de usuario

Canon

Canon GL-2 Manual de usuario

Canon

Canon PowerShot SX400 IS Manual de usuario

Canon

Canon PowerShot A4000 IS Manual de usuario

Canon

Canon EOS 70D Guía de instalación

Canon

Canon Digital IXUS 100 IS Manual de usuario

Canon

Canon EOS M5 Manual de usuario

Canon

Canon EOS 10D Digital Manual de usuario

Canon

Canon Powershot SX150 IS Manual de usuario

Canon

Canon EOS 10D Digital Manual de usuario

Canon

Canon EOS 6D Manual de usuario

Canon

Canon EOS 620-650 Manual de usuario

Canon

Canon Powershot S60 Instrucciones de montaje

Canon

Canon POWERSHOT SX500IS Manual de usuario

Canon

Canon PowerShot A400 Manual de usuario

Canon

Canon Digital Elph SD500 Manual de usuario

Canon

Canon PowerShot SX70 HS Instrucciones de montaje

Canon

Canon IXUS 950IS Manual de usuario

Canon

Canon Powershot SX40 HS Manual de usuario

Canon

Canon EOS REBEL XS Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Nikon

Nikon Coolpix 100 Manual de usuario