Canon N10-W02 Manual de usuario

PUB. DIE-0521-000B

Before using the camera, please read these instructions carefully and retain them for future

reference.

Instruction Manual

Industrial Camera

N10-W02

Table of Contents

1 Introduction 3

Introduction 3

Disclaimers 3

About the Software Used with the Camera 3

Conventions Used in this Manual 3

Safety Instructions 4

Handling Precautions 5

System Requirements 6

Names of Parts 7

2 Starting and Conﬁguring the Camera 8

Starting the Camera 8

Accessing the Camera Using a Web Browser 8

Conﬁguring the Camera 9

Using the Settings Screen 9

Setting Options 10

[Network] Menu 10

[User Management] Menu 11

[Maintenance] Menu 12

Resetting the Camera 13

Using the Web Browser 13

Using the RESET Button 13

Updating the Firmware 14

3 Additional Information 15

Speciﬁcations 15

Appendix: Physical Measurements 16

Troubleshooting 17

Error Messages 17

Index 18

1 Introduction

Introduction

This industrial camera, which is for indoor use, features PoE (Power over Ethernet) functionality. The camera is controlled by an

external device over a network. This manual explains how to conﬁgure the camera for a network. For details on how to operate the

camera, refer to the instruction manual of the system used to control the camera.

Disclaimers

• About network security: The data sent and received by the camera is not encrypted and using an unprotected network can

expose your data to monitoring by third parties. It is your responsibility to take appropriate network security measures.

Canon shall not be liable for any damage caused directly or indirectly by network security issues such as unauthorized access by

a third party.

• Canon is not responsible for damage to the camera due to how the connection cable is connected.

• Do not use the camera with medical systems and life-saving systems. Because video may be delayed or experience dropped

frames depending on the computer and network system being used, highly accurate video transmission cannot be guaranteed.

Canon shall not be liable for any damage or accidents caused from used the camera in such case.

About the Software Used with the Camera

The camera uses a software module that is distributed as freeware and whose copyrights are held by a third party. For information

on the software module incorporated in the camera and the license agreement, access the camera using a web browser, open the

[Maintenance] menu and select [View License] (A12).

Conventions Used in this Manual

• IMPORTANT: Precautions related to the camera’s operation.

• NOTES: Additional topics that complement the basic operating procedures.

• A: Reference page number.

• Brackets [ ] are used to refer to menu options as they are displayed on screen.

• Some screenshots have been altered to make them easier to read.

Trademark Acknowledgements

• Microsoft, Windows, Internet Explorer and Microsoft Edge are trademarks or registered trademarks of Microsoft Corporation in

the United States and/or other countries.

• Other names and products not mentioned above may be trademarks or registered trademarks of their respective companies.

Introduction

Safety Instructions

Be sure to read these instructions in order to operate the product safely. Follow these instructions to prevent injury or harm to the

operator of the product or others.

WARNING

Denotes the risk of serious injury or death.

• Use only power sources speciﬁed in this instruction manual for use with the product.

• Do not disassemble or modify the product.

• Do not expose the product to strong shocks or vibration.

• Do not touch any exposed internal parts.

• Stop using the product in any case of unusual circumstances such as the presence of smoke or a strange smell.

• Do not use organic solvents such as alcohol, benzine or paint thinner to clean the product.

• Do not get the product wet. Do not insert foreign objects or liquids into the product.

• Do not use the product where ﬂammable gases may be present.

This may cause electric shock, explosion or ﬁre.

• Do not shoot the sun directly or point a camera/camcorder at the sun.

Even when the sun does not appear on the screen or is behind the subject, the lens may concentrate the sunlight and cause a

malfunction or ﬁre.

• During lightning storms, do not touch the connected device's power cord or the connection cable.

This may cause electric shock.

• Do not place heavy objects on the connection cable. Do not damage, break or modify the connection cable.

This may cause ﬁre or electric shock.

• Do not allow the product to maintain contact with the same area of skin for extended periods of time during use.

This may result in low-temperature contact burns, including skin redness and blistering, even if the product does not feel hot.

• Before installing, be sure the surface is capable of supporting the total weight of the camera and connected devices, and

sufﬁciently reinforce the surface if necessary.

• Keep the product out of the reach of young children.

CAUTION

Denotes the risk of injury.

• Do not leave the product in places exposed to extremely high or low temperatures.

The product may become extremely hot/cold and cause burns or injury when touched.

Introduction

Handling Precautions

Connection/Installation

• For details on connecting and disconnecting the connection cable, be sure to refer to the instruction manual of the device

supplying power to the camera using PoE.

• Strong shocks may cause damage to the camera's connection terminal. Keep the connection cable bundled as close as possible

to the camera and do not subject the connection terminal to shocks.

Before Use

When the camera's internal temperature rises, the focus may shift slightly. After the camera starts, wait a while and then begin use.

About the CMOS Sensor

The CMOS sensor is produced using high-precision manufacturing techniques. However, if a pixel does not operate to

speciﬁcation, the effect might appear as a white or black dot on a monitor. This is the nature of CMOS sensors and does not

represent a malfunction.

Condensation

If the camera is brought into a warm room while it is cold or if the room is heated quickly, condensation may form on the camera's

external or internal surfaces. Using the camera in such case may damage it.

Cleaning

• Before cleaning the camera, be sure to disconnect the connection cable from the camera.

• Use a soft, dry cloth to clean the camera’s body. Never use chemically treated cloths or volatile solvents such as paint thinner.

• Be sure to keep the lens clean at all times. Remove dust or dirt particles using a blower and then wipe the lens.

Disposal

• Do not dispose with normal waste. Do not include the camera in waste that will be taken to a landﬁll.

• Observe the rules and regulations of your local authorities when disposing.

Introduction

System Requirements

OS Windows 7 Ultimate/Windows 7 Enterprise/Windows 7 Professional/Home Premium, SP1, 32-/64-bit

Windows 8.1 Enterprise/Windows 8.1 Pro/Windows 8.1, 32-/64-bit

Windows 10 Enterprise/Windows 10 Education/Windows 10 Pro/Windows 10 Home, 32-/64-bit

Web browser Internet Explorer 11, Microsoft Edge

(JavaScript must be enabled)

IMPORTANT

• Proper operation is not guaranteed on all computers that meet the system requirements.

Introduction

Names of Parts

Front view Back view

1 Lens

2 LAN terminal (A8)

3 RESET button (A13)

2 Starting and Conﬁguring the Camera

Starting the Camera

The camera features PoE (Power over Ethernet) functionality. The camera must be powered by a device that can supply power

using PoE and is compliant with IEEE802.3af speciﬁcations. After connecting the camera to the device using a LAN cable, power

will be supplied to the camera and it will start. Refer also to the instruction manual of the device to be connected.

IMPORTANT

• Connecting the camera using default settings to a network with multiple devices connected can cause problems with the network.

Back view

LAN terminal

Accessing the Camera Using a Web Browser

From the web browser of a computer, you can access the camera to check or change the settings. The default settings are as

follows.

IP address: 192.168.0.90

Administrator name: admin

Administrator password: password

1 Set an appropriate IP address in the network settings of the computer being connected to.

2 Start the web browser.

3 In the address bar, type the IP address and then press the Enter key.

•The user authentication screen will appear.

4 Enter the administrator name and password, and then click [OK]

•The settings screen, from which you can conﬁgure the camera’s various settings, will appear.

•You can change the administrator name and password settings in the [User Management] menu (A11).

IMPORTANT

• Make sure to change the administrator password from the default setting. Furthermore, make sure to change the password

periodically.

• If multiple cameras with the same IP address are connected to the same network, you will not be able to access the camera.

Change the camera's IP address (A10), as necessary.

Starting and Conﬁguring the Camera

Conﬁguring the Camera

You can conﬁgure the camera using the settings screen, which contains the following menus.

[Network] menu (A10): Settings related to the network the camera is connected to.

[User Management] menu (A11): Administrator name and password settings.

[Maintenance] menu (A12): Device information, license agreement, and functions such as rebooting the camera,

initializing settings and updating the ﬁrmware.

Using the Settings Screen

1 Menu selection

•Select the desired tab to switch menus. The current menu tab is highlighted.

2 Language selection

•Changes the language of the settings screen. Available languages are German, English, simpliﬁed Chinese, Korean and

Japanese. (The default setting is English.)

3 [Clear] button

•The button can be clicked after you change a menu option. Click the button to return a menu option to its previous setting after

changing it.

4 [Apply]/[Apply and reboot] button

•The button can be clicked after you change a menu option. Select [Apply] to apply the changes. If you change a menu option

with the (reboot) icon, select [Apply and reboot] to apply the changes and reboot the camera.

5 (reboot) icon

•Indicates that the camera must be rebooted to apply a change to the menu option.

IMPORTANT

• If you switch to a different menu without ﬁrst selecting [Apply] or [Apply and reboot], changes you made will be lost. To apply

changes, be sure to select the appropriate button.

• For security purposes, after you ﬁnish conﬁguring settings, close the web browser.

Starting and Conﬁguring the Camera

Setting Options

Setting options in boldface indicate default values.

[Network] Menu

Menu item Setting options / Description

[IP Address/HTTP Port]

[IP Address Settings Method] [Manual], [Auto (DHCP)]

Selects the method for conﬁguring the IPv4 settings.

[IP Address] Default: [192.168.0.90]

Assigns the IP address. When [Auto (DHCP)] is selected for [IP Address Settings Method], the IP address is

obtained from the DHCP server and displayed. When [Manual] is selected, enter a static IP address manually.

[Subnet Mask] Default: [255.255.255.0]

Assigns the subnet mask. When [Auto (DHCP)] is selected for [IP Address Settings Method], the subnet mask

is obtained from the DHCP server and displayed. When [Manual] is selected, enter a subnet mask manually,

as necessary.

[Default Gateway Address] –

Assigns the default gateway address. When [Auto (DHCP)] is selected for [IP Address Settings Method], the

default gateway address is obtained from the DHCP server and displayed. When [Manual] is selected, enter

a default gateway address manually.

[Port] Default: [80]

Assigns the port number.

IMPORTANT

• If you change network connection settings, the currently open web browser may not be able to connect to the camera. In such

case, after you select [Apply] or [Apply and reboot], a conﬁrmation dialog box will appear. To apply the changes, select [OK].

• If the web browser cannot connect to the camera after settings have been changed and the camera was rebooted, a message

will appear along with a URI for reestablishing the connection, if such a URI is available. If the camera cannot connect using the

URI, contact the system administrator.

• IP addresses that begin with [127.] (such as [127.0.0.1]) are not considered valid.

• When setting the IP address manually, ask the system administrator for the correct [IP Address], [Subnet Mask] and [Default

Gateway Address] settings.

• If the [IP Address], [Subnet Mask] or [Default Gateway Address] setting is not correct, you may not be able to access the camera

over the network. In such case, press the RESET button to reset the settings (A13) and then conﬁgure the settings again.

Tabla de contenidos

Otros manuales de Cámara digital de Canon

Canon

Canon PoverShot SD430 Manual de usuario

Canon

Canon Elph LT 260 - Elph LT 260 Zoom APS Camera Manual de usuario

Canon

Canon PowerShot SD1400IS IXUS130 Manual de usuario

Canon

Canon PowerShot SX710 HS Manual de instrucciones

Canon

Canon POWERSHOT IXUS100IS Manual de usuario

Canon

Canon IXUS850 IS Guía del usuario

Canon

Canon EOS 5DS Manual de usuario

Canon

Canon PowerShot A470 Manual de usuario

Canon

Canon EOS 1V Manual de instrucciones

Canon

Canon PowerShot G7 User Guide Advanced Manual de usuario

Canon

Canon DS126061 Manual de usuario

Canon

Canon EOS 50D Manual de usuario

Canon

Canon PowerShot SX130 IS Manual de usuario

Canon

Canon PowerShot G7 X Mark II Manual de usuario

Canon

Canon PowerShot G1 X Mark III Manual de usuario

Canon

Canon 1000D - EOS Rebel XS Transcend 8GB Memory... Manual de usuario

Canon

Canon PowerShot A95 Manual de usuario

Canon

Canon PowerShot SX410 IS Manual de usuario

Canon

Canon PowerShot A560 Instrucciones de montaje

Canon

Canon POWERSHOT A75 Manual de usuario

Canon

Canon SD450 - PowerShot Digital ELPH Camera Manual de usuario

Canon

Canon PowerShot SX110 IS Manual de usuario

Canon

Canon PowerShot S100 DIGITAL ELPH Manual de usuario

Canon

Canon IXUS 170 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Nikon

Nikon Coolpix 100 Manual de usuario