Campbell SkyVUE Pro Manual de usuario

Page 1of 3

SkyVUE Pro Ethernet Option

Document Date: March 2020

Document Issue: 1

CSL I.D - 1337

Summary

This document describes the configuration of a MOXA 5230A-T Ethernet adapter which has been

pre-installed in a SkyVUE Pro ceilometer. It should be read in combination with the User Guides for

the SkyVUE Pro and MOXA NPort 5000 Ethernet converter.

The Ethernet adaptor is setup as a TCP terminal server, which allows connection to the sensor over

an Ethernet connection, using software such as Campbell Scientific’s Viewpoint software. Any

commands that are described in the SkyVUE Pro that can be sent via the serial output can be sent via

the IP socket.

The SkyVUE Pro serial output can be converted back to standard serial (RS232/RS485) use by moving

cables inside the sensor as described below. When converted back the standard communications

cable at the base of sensor can be used as described in the SkyVUE Pro manual.

Hardware

Power from

CS135 to MOXA

Moxa Ethernet

module

Serial cable to

MOXA from DSP

Ethernet

connection

Serial output cable

to be used for

standard serial

communications

Page 2of 3

The hardware is shown in the internal view above. The Ethernet module is installed within the

SkyVUE Pro. It has serial connection (RS485) from the SkyVUE Pro and obtains power from it.

A special cable gland is fitted in the base of the SkyVUE Pro to allow a standard Ethernet cable,

pre-fitted with an RJ45 connector to be routed into the enclosure and plugged into the Ethernet

adaptor fitted inside the enclosure.

Note: RJ45 connectors which have large over mouldings may not fit through the gland.

The Ethernet cable should be

passed through the cable gland as

shown. Note that it may be

necessary to increase the diameter

of the cable, for example with heat

shrink sleeving or rubber sleeves,

to ensure a good seal around the

cable when the gland is tightened.

To convert the ceilometer back to

a standard serial connection swap

over the serial to MOXA cable

with the serial output cable as

shown.

Page 3of 3

Settings for SkyVUE Pro and Ethernet convertor as shipped

1) As supplied the SkyVUE Pro is connected for Ethernet use. It is setup for connection to the Ethernet

convertor using RS485 half-duplex mode, other settings are defaults. RS485 mode is used to allow

parallel connection of a local serially connected PC or datalogger, contact Campbell Scientific for

more information of these options.

2) The Moxa convertor as supplied is set to operate in “TCP” terminal server mode. The Moxa Interface

is set to communicate via serial port 1, using RS-485 2-wire mode. Other settings, which are the

defaults match the SkyVUE Pro defaults settings, e.g. baud rate etc.

3) The Moxa Ethernet port is set to its default static IP address of 192.168.127.254 with the SkyVUE Pro

connected to serial port 1 which is mapped to TCP port 4001 at that IP address.

4) The user will usually need to change the settings to suit their network. It may be necessary to change

the Ethernet mask and enter a gateway too (check with local IT support). It is also possible to

configure the Moxa to allow multiple remote connections to be made to the same sensor.

5) To change these settings, connect a PC to the Ethernet socket on the Moxa convertor and

communicate with it using a web browser using the address: http://192.168.127.254. The PC will

need to be configured so its IP settings allows it to connect to the 192.168.127.254 as a local

address. Once connected a web based menu system will be presented which allows you to change

the IP address of the box and setup security settings to prevent further unauthorised changes. If you

are not familiar with the setup of terminal servers please refer to the Moxa User manual, which can

be downloaded from here:

https://www.moxa.com/en/support/product-support/software-and-documentation

The model supplied is normally the 5230A-T. This has a second serial port which can be used to

connect other sensors or a datalogger to the same Ethernet connection.

Note: The SkyVUE Pro can be configured for message type, message interval and other parameters

using the USB port without disturbing any communications settings.

Otros manuales para SkyVUE Pro

Tabla de contenidos

Otros manuales de Instrumento de medición de Campbell

Campbell

Campbell CR23X Manual de usuario

Campbell

Campbell LI200R Manual de usuario

Campbell

Campbell CS525 Manual de usuario

Campbell

Campbell CMP3 Manual de usuario

Campbell

Campbell 105T Manual de usuario

Campbell

Campbell 03002 R.M Manual de usuario

Campbell

Campbell CS616 Manual de usuario

Campbell

Campbell TCAV Manual de usuario

Campbell

Campbell HMP60 Manual de usuario

Campbell

Campbell CMP3-L Manual de usuario

Campbell

Campbell CR10TCR Manual de usuario

Campbell

Campbell SR20-T2 Manual de usuario

Campbell

Campbell HMP60 Manual de usuario

Campbell

Campbell 05103 Manual de usuario

Campbell

Campbell HC2S3 Manual de usuario

Campbell

Campbell LI200S-LC Manual de usuario

Campbell

Campbell CS650 Manual de usuario

Campbell

Campbell MS-80 Manual de usuario

Campbell

Campbell CSAT3B Manual de usuario

Campbell

Campbell OBS501 Manual de usuario

Campbell

Campbell OBS-5+ Manual de usuario

Campbell

Campbell CS800-L Manual de usuario

Campbell

Campbell CS140 Manual de usuario

Campbell

Campbell CMP6-L Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario