Calculated Industries Construction Master IV Manual de usuario

User’s Guide

CONSTRUCTION MASTER

For Today’s Construction Professional

2—C

ONSTRUCTION

ASTER

INTRODUCING:

THE CONSTRUCTION MASTER IV

Designed for busy construction professionals,

the new Construction Master IV lets you solve

hundreds of dimension-related problems

quickly and accurately in Metric or feet-inch

formats!

◆Solve Dimensional Math with Ease

◆Instant Dimensional Conversions

◆Complete Metric/Imperial Conversions

◆Calculate Square and Rectangular Areas

◆Find Cubic Volumes

◆Solve Right-Triangle problems

◆Find Regular and Irregular Hip/Valley

Rafters

◆Find Regular and Irregular Jack Rafters

◆Calculate Stair Risers, Treads and Stringers

◆Solve Rake-Wall Stud Lengths

◆Convert between Volume and Weight

◆Estimate Board Feet

◆Find Circular Areas, Circumferences, Arcs

◆Material Estimations

◆Paperless Tape Function

◆And much, much more!

3 — User’s Guide

KEY DEFINITIONS/FUNCTIONS

Basic Functions

[+] [–] [x]

[÷] [=] Arithmetic operation keys.

[%] Four-function percent key.

0 – 9 Digits used for keying-in numbers.

[ • ] Decimal point.

[Off]

Turns all power off. Resets the dis-

play and all non-permanent registers.

[On/C] Turns on power. Pressing once

clears the last entry and the dis-

play. Pressing twice in succession

clears all temporary registers.

[Conv]

Used to convert between dimen-

sions. Dimensions can only be con-

verted within the same convention

(i.e., linear, square or cubic). Also

used to access special functions.

GETTING STARTED

4—C

ONSTRUCTION

ASTER

Used to find the square root of a

number.

[Conv]

x2 — Finds the square of the dis-

played value.

[M+] Memory Plus — Stores the dis-

played number in the semi-perma-

nent Memory. Also adds the

displayed number to any previous-

ly stored value in Memory. The

total stored in Memory is recalled

by pressing [Rcl] prior to [M+].

[Conv]

[M+] Memory Minus (M–) — Subtracts

the displayed value from Memory.

[Rcl] Recall — Recalls values stored in

any register (i.e., press [Rcl] and

then the key you wish to display

the value of). [Rcl] [M+] displays

Memory content.

[]

5 — User’s Guide

******************************************

[Rcl] [x] Imperial/Metric Mode — Selects

either Imperial or Metric defaults

for the following settings: pitch,

stair riser height, and on-center spac-

ing for jack rafters and rake-walls.

Note: This is a permanent setting

cleared only by removing batteries

or manually resetting.

******************************************

[Conv]

[Rcl] Memory Clear — Clears the

Memory without changing the

current display.

Dimension Keys

[Yds] Yards — This is an entry and con-

version key (when used with

[Conv]).

[Feet] Feet — This is an entry and con-

version key (when used with

[Conv]). This key can also be used

in conjunction with the [Inch] and

[/] keys for entering in Feet-Inch-

Fractions.

6—C

ONSTRUCTION

ASTER

[Inch] Inches — This is an entry and con-

version key (when used with

[Conv]). This key can also be used

in conjunction with the [/] key for

entering values in Fractional Inch

format.

[/] Fraction Bar — This key is used to

enter fractions. For example, to

enter 1/2, the key sequence would

be: 1 [/] 2.

[Cu] Cubic — This key is used with a

dimension key to identify a value

as being a volume.

Example: 5 [Cu] [Yds].

[Sq] Square — This key is used with a

dimension key to identify a value

as being an area.

Example: 10 [Sq] [Meters].

[m] Meters — This is an entry and con-

version key used to enter decimal

meters or to convert decimal

meters.

[cm] Centimeters — Entry and conver-

sion key for centimeters. Operates

the same as metric.

7 — User’s Guide

[mm] Millimeters — Entry and conver-

sion key for millimeters. Operates

the same as metric.

[Bd Ft] Board Feet — This key is used to

enter or convert cubic values to

board feet (using [Conv]). One

board foot is equal to 144 cubic

inches (1 inch x 1 foot x 1 foot).

[Weight] Weight — This key is used to con-

vert volume to a weight value using

the [Conv] key and the stored

Weight per Volume factor (see

below). Press repeatedly to toggle

between tons, pounds and kilo-

grams.

[Conv]

[%]

Weight per Volume — Used to set the

Weight per Volume factor. Factor

can be entered as Kilograms per

Cubic Meter, Tons per Cubic Yard,

or Pounds per Cubic Yard. To set a

different weight per volume, i.e.,

2150 Kilograms per Cubic Meter,

press 2150 [Conv] [%] [%] [%].

8—C

ONSTRUCTION

ASTER

Right Triangle/Rafter Keys

[Pitch] Pitch — This key is used to per-

manently enter or calculate the

pitch (slope) of a roof (or right tri-

angle). Pitch may be entered as an

inch format (9 [Inch] [Pitch]), or

as an angle in degrees (i.e., 30

[Pitch] for 30°), or also as a unit-

less ratio (0.75 [Conv] [Pitch]).

[Rise] Rise — This key enters or calcu-

lates the rise or vertical leg of a

right triangle.

[Run] Run — This key enters or calcu-

lates the run or horizontal leg (or

base) of a right triangle.

9 — User’s Guide

[Diag] Diagonal — This key enters or

calculates the diagonal leg or

hypotenuse of a right triangle.

[Conv]

[Diag] Rake-Wall — This function finds

the decreasing stud sizes in a rake-

wall based on computed or entered

values for pitch, rise and/or run.

Repeated presses of [Diag] will dis-

play the descending stud sizes from

longest to shortest.

The on-center spacing of a rake-

wall can be permanently stored by

entering a dimension prior to solv-

ing for stud sizes (for example, 750

[mm] [Conv] [Diag]

will store 750

millimeters as the on-center spac-

ing). Default on-center spacing is

600 millimeters in Metric Mode

(16 inches in English Mode).

[Hip/V] Hip/Valley — Finds the regular (45°)

hip/valley rafter length based on

entered or solved values for Pitch,

Rise, Run and/or Diagonal. If this

key is pressed after an irregular pitch

entry (see below), the length of the

10 — C

ONSTRUCTION

ASTER

irregular (non-45°) hip/valley rafter

is displayed. Answers will show an

“I” on the display to indicate if it’s

an irregular.

[Conv]

[Hip/V] Irregular Pitch — Stores the irreg-

ular pitch or slope value for calcu-

lating lengths of the irregular

hip/valley and irregular jack rafters.

For instance, to enter a 38° irregu-

lar pitch or slope, press 38 [Conv]

[Hip/V] (or, to enter a ten inch

irregular pitch, enter 10 [Inch]

[Conv] [Hip/Valley]). To recall

the irregular pitch, press [Rcl]

[Conv] [Hip/Valley]. An irregular

pitch is designated with an “I”.

Otros manuales para Construction Master IV

Tabla de contenidos

Otros manuales de Calculadora de Calculated Industries

Calculated Industries

Calculated Industries Sheet Metal/HVAC Pro Calc Manual de usuario

Calculated Industries

Calculated Industries MACHINIST CALC PRO Manual de usuario

Calculated Industries

Calculated Industries GradeMatic 4000 Manual de usuario

Calculated Industries

Calculated Industries Construction Master plus EZ 4067 Manual de usuario

Calculated Industries

Calculated Industries Frame Master II Manual de usuario

Calculated Industries

Calculated Industries Time Master II Manual de usuario

Calculated Industries

Calculated Industries Mortgage PaymentCalc 3401 Manual de usuario

Calculated Industries

Calculated Industries 4088 Manual de usuario

Calculated Industries

Calculated Industries 8525 Manual de usuario

Calculated Industries

Calculated Industries Construction Master 5 4050 Manual de usuario

Calculated Industries

Calculated Industries ConstructionMaster HeavyCalc 4320 Manual de usuario

Calculated Industries

Calculated Industries 8515 Manual de usuario

Calculated Industries

Calculated Industries Tradesman Calc 4400 Manual de usuario

Calculated Industries

Calculated Industries Construction Master IV Manual de usuario

Calculated Industries

Calculated Industries PROJECTCALC CLASSIC 8503 Manual de usuario

Calculated Industries

Calculated Industries ConcreteCalc Manual de usuario

Calculated Industries

Calculated Industries 9530 Manual de usuario

Calculated Industries

Calculated Industries 3416 Manual de usuario

Calculated Industries

Calculated Industries Ultra Scale Master 6250 Manual de usuario

Calculated Industries

Calculated Industries 3405 Manual de usuario

Calculated Industries

Calculated Industries 4065 Construction Master Pro v3.0 Manual de usuario

Calculated Industries

Calculated Industries 43285 Manual de usuario

Calculated Industries

Calculated Industries 6260 Manual de usuario

Calculated Industries

Calculated Industries KitchenCalc Pro Manual de usuario

Manuales populares de Calculadora de otras marcas

HP 35s Manual

Casio

Casio CFX-9970G Manual de usuario

LEXIBOOK

LEXIBOOK EL350 Manual de usuario

HP HP-97 Manual de usuario

Citizen

Citizen SDC-414N Manual de usuario

Casio

Casio fx-3800P Manual de usuario

Canon

Canon P26-DHIII Manual de usuario

Citizen

Citizen 520DPA Manual de usuario

Sharp

Sharp EL-9900 Manual de usuario

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Manual de usuario

Casio

Casio MS-7UC Manual de usuario

Sharp

Sharp WriteView EL-W506 Manual técnico

Casio

Casio FC-200 Manual de usuario

Casio

Casio fx-CG50 Manual de usuario

HP HP-67 Guía del usuario

Royal

Royal CBC2000 Manual de usuario

Heathkit

Heathkit IC-2009 Manual de usuario

Universal

Universal UNV-15907 Manual de usuario