Calculated Industries 8527 Manual de usuario

PROJECTCALC

PLUS

4840 Hytech Drive

Carson City, NV 89706 U.S.A.

1-800-854-8075 or 1-775-885-4900

Fax: 1-775-885-4949

E-mail: [email protected]

www.calculated.com

Model 8527

TABLE OF CONTENTS

Key Definitions ................................1

Basic Dimensional Math....................10

Linear Conversions ................................10

Square and Cubic Conversions ..............11

Basic Dimensional Math ........................11

“Square-up”/Diagonal ............................12

Project Examples-Using Default Values..12

Paint: Gallons, Quarts, or Pints of ..........12

Wallpaper: Rolls of..................................13

Tiles: Number of ....................................13

Custom Tiles: Number of - Using Other

Than Default Custom Size....................14

Deck: Number of Boards ........................15

Fence: Number of Fence Boards,

Posts and Rails....................................15

Board Feet: Lumber Estimation ..............16

Studs: Number of ..................................16

Roofing: Bundles of Roof Shingles ........17

Drywall: Number of 4’ x 8’ Sheets ..........17

Carpet: Length of ....................................17

Concrete: Bags of ..................................18

Bricks/Blocks: Number of, for a Wall......18

Gravel: Tons of........................................19

Mulch: Number of Bags..........................19

Finding the Cost of Materials ..............20

Auto Shut-Off and Batteries ................20

Repair and Return ..........................21

OCKET

EFERENCE

UIDE

- 1

o-On/Clear Key

Turns power on. Pressing once

clears the display. Pressing twice

clears all temporary values.

Ç o - Off

Turns all power off, clearing all non-

permanent registers.

r- Recall

Recalls stored values.

+ – x ÷ =

Arithmetic operation keys.

0- 9and

•

Digits used for keying in numbers.

Dimensional Unit Keys

y- Yards Key

Enters or converts to Yards.

f- Feet Key

Enters or converts to Feet as whole

or decimal numbers. Also used with

the i and /keys for entering

Feet-Inch-Fraction values (e.g., 6

f 9 i 1 / 2 ). Repeated

presses during conversions toggle

between Feet-Inch-Fractions and

Decimal Feet.

KEY DEFINITIONS

OCKET

EFERENCE

UIDE

- 2

i- Inch Key

Enters or converts to Inches. Entry

can be whole or decimal number.

Also used with the /key for entering

Fractional Inch values (e.g., 9i

1 / 2 ). Repeated presses during

conversions toggle between

Fractional and Decimal Inches.

/- Fraction Bar Key

Used to enter fractions. Fractions

can be entered as proper (1/2, 1/8,

1/16) or improper (3/2, 9/8).

m- Meter Key

Enters or converts to Meters.

Convert Key Functions

Ç-Convert Key

Used with the dimensional unit keys

to convert between dimensions, the

Project Keys to calculate material

quantities, or with other keys to

access special functions.

Ç x - CClleeaarrAAllll

Clears all stored values and sets cal-

culator back to defaults.

Ç / - Percent

(%)

Four-function (+, -, x, ÷) percent

OCKET

EFERENCE

UIDE

- 3

Ç – - Change Sign

(+ / -)

Toggles displayed value to positive or

negative. (Repetitive presses of Ç

–will change sign from positive or

negative.)

Ç ÷ - Square Root

Finds Square Root of value in display.

Ç + -x2

Finds Square of value in display.

Ç s - Pi

(

)

Constant 3.141593.

Memory

s m

(M+)

- Adds or stores a value

in the semi-permanent memory (e.g.,

1 5 0 s m). Semi-permanent

means the value is cleared when the

calculator is turned off.

Ç – s m

(M-)

- Subtracts a

value from the semi-permanent

Memory (e.g., 1 5 0 Ç – s

msubtracts 150 from the memory).

r m

(M-R/C)

- Recalls Memory value

(e.g., if 150 has been stored in Memory,

pressing r m will display 150).

r r - Displays and clears Memory

value.

OCKET

EFERENCE

UIDE

- 4

Entering Square or Cubic

To label a dimension as “Square” or

“Cubic,” enter the value, then press the

desired dimension key twice for

Square and three times for Cubic. For

example, to enter 25 Cubic Yards,

press 2 5 y y y.

Fraction Resolution

Your calculator is set to display Fractional

values to the nearest 16th of an Inch

(default setting). Press r / to access

the fraction resolution setting. Repeated

presses of /will then revolve through

the available settings: 1/16, 1/32, 1/64,

1/2, 1/4 and 1/8. Press oto exit.

Project Keys

p- Paint

Calculates volume of paint, based on

an entered area and a stored Paint

Coverage per Gallon (see below).

Finds quantity in Gallons, Quarts or

Pints upon repeated presses.

s p - Stores Paint Coverage

Stores Paint Coverage per Gallon. To

recall this setting, press r p.

Default is 350 sq.ft. per gallon.

OCKET

EFERENCE

UIDE

- 5

w- Wallpaper

Calculates number of rolls of wallpaper,

based on an entered area and a stored

Wallpaper Roll Coverage Area (see

below).

s w - Stores Wallpaper Roll

Coverage Area

Stores Coverage Area (in Square

Feet) per Wall-paper Roll. To recall

this setting, press r w. Default

is 56 Square Feet per roll.

t - Tile

Finds the number of tiles, based on

an entered area and a user-stored

Grout Width (see below). Repeated

presses will scroll between numbers

of tiles for various “standard” tile

sizes (18”, 16”, 13”, 12”, 10”, 8”, 6”,

4”, 2”, 1” and 24”).

Note: Tile sizes shown in Inches, not Square

Inches (as used in custom tile size calculations).

In other words, a 6” tile is really 6” x 6”, or a 36

Square-Inch tile, but it is labeled as a 6” size.

s t - Stores Grout Width

Stores Grout Width in Inches; used in

calculating the number of tiles (see

above). To recall this setting, press

r t. Default is 0 (no grout width).

d- Deck

Finds the number of boards for a deck,

based on an entered area and a stored

Board Width or Board On-Center

(see below). Repeated presses will

scroll between numbers of boards for

various “standard” board lengths

(12’, 10’, 8’, 20’, 18’, 16’ and 14’).

s d - Stores Board Width/O.C.

Stores Board Width or Board On-center

for deck or fence calculations. To recall

this setting, press r d. Also used

to store the board On-center for Fence

Spacing. Default is 5-11/16 Inches.

F- Fence

Multi-function key that finds the

number of fence boards, number of

posts and number of rails based on

an entered distance, Board

Width/O.C. and post spacing.

s F - Stores Post Spacing

Stores Post Spacing On-center for

fence in Feet-Inches. To recall this set-

ting, press r F. Default is 8 Feet.

Ç 7 - Board Feet

Calculates number of board Feet

based on entered volume. One board

foot equals 144 Cubic Inches.

OCKET

EFERENCE

UIDE

- 6

OCKET

EFERENCE

UIDE

- 7

Ç8- Studs

Calculates number of studs, based on

an entered linear distance and a stored

On-Center Spacing (see below).

Note: Automatically adds one stud to the calcu-

lated answer to account for one on the end.

s 8 - Stores On-Center for Studs

Stores On-center spacing for studs in

Inches. To recall this setting, press

r8. Default is 16”.

Ç 9 - Roof Bundles

Calculates number of bundles of roof

shingles, based on an entered roof

area and a stored Area per Roof

Bundle (see below).

s 9 - Stores Area per Roof Bundle

Stores the Coverage Area per Roof

Bundle. To recall this setting, press

r 9. Default is 33.33 sq.ft.

Ç 4 - 4x8 Sheet

Calculates number of 4’ x 8’ sheets

(for drywall, paneling), based on

entered linear distance or area.

Ç 5 - Carpet

Calculates carpet length required (of

either 12’, 13’ or 15’-wide carpet rolls),

based on entered area. Repeated

presses of 5will scroll between values

for 12’, 13’, and 15’ rolls.

OCKET

EFERENCE

UIDE

- 8

Ç 6 - Custom Tile

Calculates number of tiles based on an

entered area and a stored Custom Tile

Size (see below). This is used sepa-

rately from the regular Tile Key ( t).

Note: Calculation does not account for grout width

for custom tiles, so you will need to adjust for this.

s 6 - Stores Custom Tile Size

Stores Custom Tile Size in Square

Inches. To recall this setting, press

r 6. Default is 24 Square Inches.

Ç 1 - Concrete

Calculates the number of bags of con-

crete required, based on an entered vol-

ume (e.g., cubic feet or cubic yards) and

a stored Volume per Bag (see below).

s 1 - Stores Concrete Volume per Bag

Stores the Volume per Bag of

concrete. To recall this setting, press

r 1. Default is 0.67 Cubic Feet

per bag (80 lbs.).

Ç 2 - Brick

Calculates the number of standard

eight Inch-size U.S. bricks (with 3/8”

mortar) based on entered linear

distance (or area, volume) for both

“face” (21-Square Inch) and “paver”

(32-Square Inch) brick applications.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Calculadora de Calculated Industries

Calculated Industries

Calculated Industries ConcreteCalc Manual de usuario

Calculated Industries

Calculated Industries PlumbingCalc Pro Manual de usuario

Calculated Industries

Calculated Industries 3423 Manual de usuario

Calculated Industries

Calculated Industries ElectriCalc Pro 5060 Manual de usuario

Calculated Industries

Calculated Industries Time Master II Manual de usuario

Calculated Industries

Calculated Industries Construction Master 5 Manual de usuario

Calculated Industries

Calculated Industries 8305 KitchenCalc Pro Manual de usuario

Calculated Industries

Calculated Industries SCALE MASTER CLASSIC 6020 Manual de usuario

Calculated Industries

Calculated Industries Mortgage PaymentCalc 3401 Manual de usuario

Calculated Industries

Calculated Industries Hot Rod Calc 8703 Manual de usuario

Calculated Industries

Calculated Industries Real Estate Master IIx Manual de usuario

Calculated Industries

Calculated Industries Measure Master 4018 Manual de usuario

Calculated Industries

Calculated Industries Ultra Measure Master Manual de usuario

Calculated Industries

Calculated Industries 3265 Manual de usuario

Calculated Industries

Calculated Industries ULTRA MEASURE MASTER 8020 Manual de usuario

Calculated Industries

Calculated Industries ProjectCalc Plus MX 8528 Manual de usuario

Calculated Industries

Calculated Industries 3430 Manual de usuario

Calculated Industries

Calculated Industries KitchenCalc 8300 Manual de usuario

Calculated Industries

Calculated Industries ConstructionMaster HeavyCalc 4320 Manual de usuario

Calculated Industries

Calculated Industries ScheduleCalc Manual de usuario

Calculated Industries

Calculated Industries Kitchen Calc PRO Master Chef's Edition 8305 Manual de usuario

Calculated Industries

Calculated Industries Quilter's FabriCalc 8400 Manual de usuario

Calculated Industries

Calculated Industries 4030 Manual de usuario

Calculated Industries

Calculated Industries ElectriCalc Pro Manual de usuario

Manuales populares de Calculadora de otras marcas

HP 35s Manual

Casio

Casio CFX-9970G Manual de usuario

LEXIBOOK

LEXIBOOK EL350 Manual de usuario

HP HP-97 Manual de usuario

Citizen

Citizen SDC-414N Manual de usuario

Casio

Casio fx-3800P Manual de usuario

Canon

Canon P26-DHIII Manual de usuario

Citizen

Citizen 520DPA Manual de usuario

Sharp

Sharp EL-9900 Manual de usuario

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Manual de usuario

Casio

Casio MS-7UC Manual de usuario

Sharp

Sharp WriteView EL-W506 Manual técnico

Casio

Casio FC-200 Manual de usuario

Casio

Casio fx-CG50 Manual de usuario

HP HP-67 Guía del usuario

Royal

Royal CBC2000 Manual de usuario

Heathkit

Heathkit IC-2009 Manual de usuario

Universal

Universal UNV-15907 Manual de usuario