Cabletron Systems MMAC-M5FNB Manual de usuario

MMAC-M5FNB

MULTI-MEDIA ACCESS CENTER

OVERVIEW AND SETUP GUIDE

CABLETRON SYSTEMS, P.O. Box 5005, Rochester, N.H. 03867-0505

NOTICE

Cabletron Systems reserves the right to make changes in

speciﬁcations and other information contained in this document

without prior notice.The reader should in all cases consult Cabletron

Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is

subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR

ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL

DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO

LOST PROFITS) ARISING OUT OF OR RELATED TO THIS

MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF

CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR

SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH

DAMAGES.

Cabletron Systems, Inc.

P.O. Box 5005

Rochester, NH 03866-5005

Printed in the United States of America

Order number: 9030748-02 September 1994

SPECTRUM

LANVIEW

, and

Multi Media Access Center

are

registered trademarks and

MMAC-M5FNB, MIM,

and

M5PSM

are

trademarks of Cabletron Systems, Inc.

Ethernet

is a trademark of Xerox Corporation.

IBM

is a registered trademark of International Business Machines

Corporation

NOTICE

FCC NOTICE

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Note

:This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC

rules.These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment.This equipment uses, generates, and can

radiate radio frequency energy and if not installed in accordance with

the operator’s manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause interference, in which case the user will be required to

correct the interference at his own expense.

WARNING:

Changes or modifications made to this device which are

not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

DOC NOTICE

This digital apparatus does not exceed the Class A limits for radio

noise emissions from digital apparatus set out in the Radio

Interference Regulations of the Canadian Department of

Communications.

Le Présent appareil numérique n’émet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numériques de la class

A prescrites dans le Règlement sur le brouillage radioélectrique édicté

par le ministère de Communications du Canada.

BABT NOTICE

This device is approved under BABT General Approval No.

NS/G/1234/J/100003 for indirect connection to public

telecommunications systems in the United Kingdom.

NOTICE

iii

VCCI NOTICE

This equipment is in the 1st Class Category (information equipment

to be used in commercial and/or industrial areas) and conforms to the

standards set by the Voluntary Control Council for Interference by

Information Technology Equipment (VCCI) aimed at preventing radio

interference in commercial and/or industrial areas.

Consequently, when used in a residential area or in an adjacent area

thereto, radio interference may be caused to radios and TV receivers,

etc.

Read the instructions for correct handling.

CONTENTS

CHAPTER 1 INTRODUCTION

1.1 Using This Manual ....................................................................1-1

1.2 Using the MMAC-M5FNB Manual Set ....................................1-2

1.3 Getting Help...............................................................................1-2

1.4 The MMAC-M5FNB Multi Media Access Center.....................1-3

1.5 MMAC-M5FNB Features..........................................................1-4

CHAPTER 2 INSTALLATION REQUIREMENTS

AND SPECIFICATIONS

2.1 Site Guidelines...........................................................................2-1

2.2 MMAC-M5FNB Configuration Guidelines...............................2-2

2.3 Operating Specifications............................................................2-2

CHAPTER 3 MMAC-M5FNB SETUP

3.1 Unpacking the MMAC-M5FNB ................................................3-1

3.2 Setting Up the MMAC-M5FNB.................................................3-2

3.2.1 Rack Mounting the MMAC-M5FNB............................3-2

3.2.2 Rack Mounting the Cable Tie Tray..............................3-4

3.2.3 Inserting the Fan Tray .................................................3-5

3.2.4 Installing the Power Supply Module............................3-6

3.2.5 Installing the Security Bars.........................................3-9

3.2.6 Powering Up the MMAC-M5FNB..............................3-11

INTRODUCTION

Page 1-1

CHAPTER 1

INTRODUCTION

The

MMAC-M5FNB™ Multi Media Access Center

offers

maximum ﬂexibility and convenience in the design and operation of

your network.The enclosure provides space for one

Repeater/Management Module and up to ﬁve Media Interface

Modules (MIM™); or, by removing one of the ﬁve MIMs, you can add a

second, load-sharing power supply module.

This manual is an installation and reference guide. It lists the

features and options of the MMAC-M5FNB and explains how to

install the fan tray, power supply(ies), and security bars.You should

read through this manual prior to using the MMAC-M5FNB to gain a

full understanding of the MMAC-M5FNB and its capabilities.

CAUTION:

Only qualiﬁed personnel should install or service this unit

and its modules!

1.1 USING THIS MANUAL

Chapter 1,

Introduction

, discusses the features and capabilities of

the MMAC-M5FNB.

Chapter 2,

Installation Requirements and Speciﬁcations

, lists

the location requirements that must be met before you install the

MMAC-M5FNB on your network.This chapter also includes some

MIM conﬁguration guidelines, environmental guidelines, and

operating speciﬁcations for the MMAC-M5FNB and related Power

Supply Modules (M5PSM™).

Chapter 3,

MMAC-M5FNB Setup

, contains instructions for rack

mounting your MMAC-M5FNB, inserting the fan tray, installing the

power supply(ies), installing the security bars, and powering up the

MMAC-M5FNB.

INTRODUCTION

Page 1-2

1.2 USING THE MMAC-M5FNB MANUAL SET

Other manuals have been developed for the Repeater/Management

modules and for each MIM that can be installed in your

MMAC-M5FNB. These manuals explain how to install the individual

modules into the MMAC-M5FNB, how to attach cable segments to the

modules, and how to test those segments after they have been

installed. Speciﬁcations for all modules are included in each manual.

Additional manuals have been developed on how to use Cabletron

Systems’ Network Control Management software packages.

Each manual in this set assumes that you have a general working

knowledge of Ethernet or IEEE 802.3, 802.5, or FDDI type data

communications networks and their physical layer components.

1.3 GETTING HELP

If you need additional support related to the MMAC-M5FNB, or if you

have any questions, comments, or suggestions related to this manual,

contact Cabletron Systems Technical Support. Before calling, please

have the following information ready:

• The product type (MMAC-M5FNB), and the product serial

number.The serial number is located on the front panel of the

MMAC, and the product type is on the fan tray label.

You can contact Cabletron Systems Technical Support Department by

any of the following methods:

By phone: Monday through Friday between

8 A.M. and 8 P.M. Eastern

Standard Time at (603) 332-9400.

By mail: Cabletron Systems, Inc.

PO Box 5005

Rochester, NH 03867-0505

By CompuServe

: GO CTRON from any ! prompt

INTRODUCTION

Page 1-3

By Internet mail: [email protected]

By FAX: (603) 337-3075

By BBS: (603) 335-3358 (4 lines available)

1.4 THE MMAC-M5FNB MULTI MEDIA ACCESS CENTER

The Cabletron Systems MMAC-M5FNB is a complete modular

approach to integrated networks.The MMAC-M5FNB supports Local

Area Networks compliant to IEEE 802.3, IEEE 802.5, and FDDI

standards. It also supports all of the Cabletron Systems Media

Interface Modules (MIMs).

A variety of IEEE 802.3, IEEE 802.5, and FDDI compliant media can

be connected to the MMAC-M5FNB, including shielded and

unshielded twisted pair, ﬁber optic cable, thick or thin coaxial cable,

and standard AUI transceiver cable. Each media type has a MIM

which, when installed into the MMAC-M5FNB, is compatible with all

other MIMs installed in that unit.You can have complete network

integration of a variety of media through a single source.

The MMAC-M5FNB is designed so that network expansions or

changes in media types can be done without bringing down the entire

network. In a matter of minutes, you can add, change, or replace

MIMs without turning off the MMAC-M5FNB or using any special

tools.This design also allows the MMAC-M5FNB to adapt to

ever-changing industry standards. Figure 1-1 (following page)

illustrates an MMAC-M5FNB equipped with a variety of MIM cards.

CAUTION:

Only qualiﬁed personnel should install or service this unit

and its modules!

INTRODUCTION

Page 1-4

Figure 1-1. MMAC-M5FNB with Optional MIMs

1.5 MMAC-M5FNB FEATURES

Universal Power Supply

The MMAC-M5FNB power supply senses and automatically adjusts to

the input voltage and frequency. No additional adjustments are

necessary.

Built-in Power Supply Protection

The power supply module(s) automatically powers down under any of

the following conditions: thermal overload (thermal protection);

shorted output (over current, or short circuit protection); or excess

output voltage (over voltage protection).The power supply will

automatically recover when a thermal overload condition is corrected;

when an over current or over voltage condition is corrected, the power

POWER OK FAIL

FAULT

+5 VOLT TEST

-5 VOLT TEST

+12 VOLT TEST

-9 VOLT TEST

COMMON

POWER FAIL

MMAC-M5FNB

The Complete Networking Solution™

Multi Media Access Center

100-125V ~ 5A

220-250V ~ 3A

50/60Hz

100-125V ~ 5A

220-250V ~ 3A

50/60Hz

M5PSM

ACTIVE UTP

TOKEN RING

LNK

PEN

16MB MGMT

ERR

TRMIM-22A

16MB

TRMIM-4A

MGMT

ACTIVE UTP

TOKEN RING

ERR

RI RO

CRS16

WFLT

WRAP

FLNK

LNK

PEN

RCV POK

CLN

TPRMIM-36

10BASE-T

ETHERNET

RCV POK

ETHERNET

B C

CLN

CXRMIM

10BASE-2

ETHERNET

ETHERNET B C CLN

POK

RCV

POKRCV POKRCV

M5PSM

POWER OK FAIL

FAULT

+5 VOLT TEST

-5 VOLT TEST

+12 VOLT TEST

-9 VOLT TEST

COMMON

POWER FAIL

EMME

RESET

ON PWR

BOK

STBYA

STBYB

RCVA

RCVB

RCVC

RCVD

ERR

STBYC

STBYD

CLNA

CLNB

CLNC

CLND

PWR

ETHERNET

INTRODUCTION

Page 1-5

supply requires AC power cycling (turn power switch off, then on

again) to recover.A FAULT LED on the power supply module indicates

when an over current condition has occurred.

Note:

If you remove, then re-insert, the fan tray with no MIMs installed

in the chassis and the power on, you will have to turn each power

supply off, then on again to re-start.

Power OK Signal

The same signal that illuminates the Power OK LED on the power

supply module(s) will also alert the management module that the

power supply is functioning normally.

Power Factor Correction

The MMAC-M5PSM meets the EN60555-2 limits for power factor

correction, which may be required by utility companies in the near

future.

The power factor correction feature provides a number of advantages.

By improving this factor to meet the EN60555-2 limits, line noise and

peak current levels are dramatically reduced and the amount of power

available to the user is increased. Power factor correction also reduces

stress on fuses, circuit breakers, wall sockets, wiring, and

transformers.

Redundant Power with Current Sharing

The MMAC-M5FNB can operate with either one or two power supply

modules. If two MMAC-M5PSMs are installed, they share the power

load requirements of the installed MIMs; if one power supply fails,the

second automatically assumes the entire load.This ensures that your

network will remain operational until a replacement MMAC-M5PSM

can be installed.The two power supply modules use a current sharing

scheme such that each power supply provides 50% of the required load

(

5%, 5V output only) under all load conditions.

Tabla de contenidos

Otros manuales de Hardware de red de Cabletron Systems

Cabletron Systems

Cabletron Systems Netlink FRX4000 Instrucciones de montaje

Cabletron Systems

Cabletron Systems WPIM-S/T Manual de usuario

Cabletron Systems

Cabletron Systems 9A426-01 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-M3FNB Manual de usuario

Cabletron Systems

Cabletron Systems TRBMIM-T Manual de usuario

Cabletron Systems

Cabletron Systems SWPIM-E1 Manual de usuario

Cabletron Systems

Cabletron Systems SSIM-T8-04 Manual de usuario

Cabletron Systems

Cabletron Systems Expansion module DELHE-UA Manual de usuario

Cabletron Systems

Cabletron Systems FE-100 Manual de usuario

Cabletron Systems

Cabletron Systems MMAC-Plus 9A128-01 Manual de programación

Cabletron Systems

Cabletron Systems HSIM HSIM-A6DP- Manual de usuario

Cabletron Systems

Cabletron Systems Device Management Module Dec GigaSwitch Manual de usuario

Cabletron Systems

Cabletron Systems BRIM-A6DP Manual de usuario

Cabletron Systems

Cabletron Systems TRMIM-22 Manual de usuario

Cabletron Systems

Cabletron Systems IRBM/LM Manual de usuario

Cabletron Systems

Cabletron Systems 9C300-1 Manual de usuario

Cabletron Systems

Cabletron Systems ELS10-26 Manual de usuario

Cabletron Systems

Cabletron Systems BRIM F6 BRIM-F6 Manual de usuario

Cabletron Systems

Cabletron Systems 5000, 5500 Manual de usuario

Cabletron Systems

Cabletron Systems Spectrum EMM-E6 Instrucciones de instalación y funcionamiento

Cabletron Systems

Cabletron Systems CRBRIM-W/T Manual de instalación

Cabletron Systems

Cabletron Systems WPIM-DDS Manual de programación

Cabletron Systems

Cabletron Systems MMAC-Plus 9G536-04 Manual de usuario

Cabletron Systems

Cabletron Systems EPIM-3PS Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario