BYOC Optical Compressor Manual de usuario

Build Your Own Clone

Optical Compressor Kit

Instructions

Warranty:

BYOC, LLC guarantees that your kit will be complete and that all parts and

components will arrive as described, functioning and free of defect. Soldering,

clipping, cutting, stripping, or using any of the components in any way voids this

guarantee. BYOC, LLC guarantees that the instructions for your kit will be free of

any majors errors that would cause you to permanently damage any components

in your kit, but does not guarantee that the instructions will be free of typos or

minor errors. BYOC, LLC does not warranty the completed pedal as a whole

functioning unit nor do we warranty any of the individual parts once they have

been used. If you have a component that is used, but feel it was defective prior to

you using it, we reserve the right to determine whether or not the component was

faulty upon arrival. Please direct all warranty issues to:

[email protected] This would include any missing parts issues.

Return:

BYOC, LLC accepts returns and exchanges on all products for any reason, as long as

they are unused. We do not accept partial kit returns. Returns and exchanges are for the

full purchase price less the cost of shipping and/or any promotional pricing. Return

shipping is the customers responsiblity. This responsibility not only includes the cost of

shipping, but accountability of deliver as well. Please contact

[email protected] to receieve a return authorization before mailing.

Tech Support:

BYOC, LLC makes no promises or guarantees that you will sucessfully complete your kit

in a satisfactory mannor. Nor does BYOC, LLC promise or guarantee that you will

receive any technical support. Purchasing a product from BYOC, LLC does not entitle

you to any amount of technical support. BYOC, LLC does not promise or guarantee that

any technical support you may receive will be able to resolve any or all issues you may

be experiencing.

That being said, we will do our best to help you as much as we can. Our philosophy at

BYOC is that we will help you only as much as you are willing to help yourself. We

have a wonderful and friendly DIY discussion forum with an entire section devoted to the

technical support and modifications of BYOC kits.

www.buildyourownclone.com/board

When posting a tech support thread on the BYOC forum, please post it in the correct

lounge, and please title your thread appropriately. If everyone titles their threads

“HELP!”, then it makes it impossible for the people who are helping you to keep track of

your progress. A very brief discription of your specific problem will do. It will also

make it easier to see if someone else is having or has had the same problem as you. The

question you are about to ask may already be answered. Here are a list of things that you

should include in the body of your tech support thread:

1. A detailed explanation of what the problem is. (not just, “It doesn’t work, help”)

2. Pic of the top side of your PCB.

3. Pic of the underside of your PCB.

4. Pic that clearly shows your footswitch/jack wiring and the wires going to the PCB

5. A pic that clearly shows your wiring going from the PCB to the pots and any other

switches(only if your kit has non-PC mounted pots and switches)

6. Is bypass working?

7. Does the LED come on?

8. If you answer yes to 6 and 7, what does the pedal do when it is "on"?

9. Battery or adapter.(if battery, is it good? If adapter, what type?)

Also, please only post pics that are in focus. You're only wasting both parties' time if you

post out of focus, low res pics from your cell phone.

Revision Notes:

Rev 2.1(current) There are no known errors in this revision.

Go to: www.buildyourownclone.com/opticompV1.pdf to download instructions for the

previous version of the otptical compressor kit.

Copyrights:

All material in this document is copyrighted 2009 by BYOC, LLC

OPTICAL COMPRESSOR KIT

INSTRUCTION INDEX

Parts Checklist……………………..............…….....page 4 - 5

Populating the Circuit Board…………...................page 6 - 13

Assembly………………………………....................page 15 - 17

Wiring the Footswitch & Jacks................................page 18 - 20

Installing the IC.........................................................page 21

Schematic....................................................................page 22

Parts Checklist for BYOC Optical Compressor

Resistors:

2 - 4.7k (yellow/purple/black/brown/brown)

2 - 10k (brown/black/black/red/brown)

4 - 100k (brown/black/black/orange/brown)

2 - 220k (red/red/black/orange/brown)

1 - 470k (yellow/purple/black/orange/brown)

2 - 1M(brown/black/black/yellow/brown)

Capacitors:

1 - .01µf/1n film (10n)

4 - .047µf/47n film (47n)

3 - 0.1µf/100n film (100n) [use only for bass guitar]

2 - 33µf aluminum electrolytic

1 - 100µf aluminum electrolytic

Diodes:

1 - 1N4001

Transistors:

2 - 2N5088

IC's:

1 - 4558 or similar DIP-8 dual operational amplifier

Optocoupler:

1 - VTL5C4(single element with 4 leads) or VTL5C4/2(dual element with 5 leads)

Potentiometers: Be sure to snap off the small tab on the side of each panel mounted

pot.

1 -

B500k linear (sustain knob)

1 - B500k linear (sustain knob)

1 - A100k audio(volume knob)

Hardware:

1 - drilled enclosure w/ 4 screws

1 - byoc Optical Compressor circuit board

1 - 3PDT footswitch

2 - knobs

1 - AC adaptor jack

1 - ¼”mono jack

1 - ¼”stereo jack

1 - red LED

1 - battery snap

4 - bumpers

hook-up wire

Populating the Circuit Board

STEP 1: Add the resistors. Resistors are not polarized, so it does not matter which end

goes in which solder pad.

STEP 2: Add the diode. The 1N4001 will be black with a silver stripe. Be sure to

matched the end of the diode with the stripe to the layout on the PCB. The stripped end

should go in the square solder pad.

STEP 3: Add the IC socket. Line up the U shaped notch of the socket to the notch on the

PCB layout. Solder only the IC socket to the PCB. Do not solder the actual IC. The IC

inserts into the socket the same way you'd plug a vacuum tube into a socket. See page

21 for instructions on how to install the IC into the socket.

STEP 4: Add the film capacitors. These are not polarized so they can be inserted into

the PCB in either direction. If you are building for use with bass guitar, you should use

the .1uf(100n) capacitors in the places marked with an “*”.

STEP 5: Add the transistors. Match the flat side of the transistor to the flat side of the

layout on the PCB.

Otros manuales para Optical Compressor

Tabla de contenidos

Otros manuales de Pedal de música de BYOC

BYOC

BYOC Bass Chorus Manual de usuario

BYOC

BYOC Stereo Analog Flanger Manual de usuario

BYOC

BYOC Lazy Sprocket Manual de usuario

BYOC

BYOC Li'l Analog Chorus Kit Manual de instrucciones

BYOC

BYOC Octave Fuzz Manual

BYOC

BYOC E.S.V. Fuzz Manual de usuario

BYOC

BYOC Phase Royal Manual de usuario

BYOC

BYOC Large Beaver Ram's Head Manual de usuario

BYOC

BYOC Octavefuzz Manual de usuario

BYOC

BYOC Super 8 Manual

BYOC

BYOC Soaring Skillet Manual de usuario

BYOC

BYOC Chancellor Overdrive Manual de usuario

BYOC

BYOC A/B True Bypass Looper Manual de usuario

BYOC

BYOC BA6110 Manual de usuario

BYOC

BYOC Analog Chorus Manual

BYOC

BYOC Bass Overdrive Manual

BYOC

BYOC Full Circle Bass Fuzz Manual

BYOC

BYOC Classic Fuzz Manual de usuario

BYOC

BYOC Parametric Multi-Band Compressor Manual de usuario

BYOC

BYOC Classic Phaser Manual de usuario

BYOC

BYOC Shredder Manual de usuario

BYOC

BYOC Analog Chorus Manual de usuario

BYOC

BYOC Phase Royal Manual de usuario

BYOC

BYOC Spring Reverb Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario

TREX

TREX ToneBug Totenschläger Manual de usuario