Bushnell ImageView 11-1026 Manual de usuario

Model #: 111026

LIT. #: 980828/0412

Instruction

Manual Version 3.0

TABLE OF CONTENTS PAGE

ENGLISH

FRANÇAIS

ESPAÑOL

DEUTSCH

ITALIANO

4-17

18-31

32-45

46-59

60-73

Congratulations on your purchase of the Bushnell ImageView®binocular!

The Bushnell ImageView binocular takes the technology of digital

photography and combines it with a high-quality compact binocular.

This allows you to observe sporting events, wildlife, scenic vistas or

anything you would normally use a binocular for, and then save the

image in a built-in attached digital camera. You can then download these

images to your computer and e-mail them to your friends and family,

print out the pictures, or save them in a photo album for future use.

Before using the product, please read the instructions contained in this

manual and take time to familiarize yourself with the different parts and

features of the product.

ENGLISH

Camera and Binocular Parts Guide

Camera

Lens

Power/

MODE

Button

Binocular Focus

SNAP

Button

Battery

Compartment

USB

Port

SD Card

Slot

CAMERA PARTS Setup and Basic Operation

1. The camera is powered by two AAA alkaline, lithium, or NiMh batteries (not

included). Insert batteries into the compartment, with the springs in contact with

the negative (at) end of each battery. A power meter on the top right of the

display indicates battery condition.

2. Insert an SD card ("upside down" with metal contacts facing up) in the slot if

greater storage is desired. You may use SD cards (not MMC cards) up to 32 GB

capacity.

3. Press and hold the MODE button for two seconds to turn on the camera. The

camera will turn o automatically after about 3 minutes if no buttons are pressed.

Note: when the camera is connected to a computer via the supplied USB cable, the

camera will draw power from the computer with no battery drain.

4. Hold the ImageView steady and press SNAP to take a picture (or start/stop

shooting a video, when the camera is in video mode). The camera focus is preset

to take sharp photos from approximately 75 feet to innity.

Using the Optional Operating Modes

Your ImageView is already setup to produce high quality results right out of the box,

and it is not necessary to use the optional modes-you may simply press the SNAP

button and start taking photos. However, as you might want to shoot a video clip, delete

one or more previous photos, or explore other options, we recommend you review the

available operating modes listed in the chart below. Briey pressing the MODE button

will step through these operational modes in the listed order, and you will see the icon

for each mode on the display. Use the SNAP button to perform the operation after

selecting the icon. If you don't press SNAP within 5 seconds, the camera will return to its

normal operation and display.

Mode Icon Description

Self-Timer Clock Photo is taken after a 10 second delay when SNAP is pressed (in

normal still photo mode.) This can be used to avoid accidently

shaking the camera when the SNAP button is pressed. The timer

automatically cancels after use.

Video Movie

Camera

Select the movie camera icon, then begin shooting by pressing

SNAP. The counter will show the elapsed time while recording

the video clip. The camera will continue recording video until

you stop it by pressing SNAP again, or until there is no more

memory available to store it (whichever occurs rst). The counter

will advance by one, indicating the video le has been saved.

The camera automatically returns to normal still photo mode

after a video has been shot. Video resolution=640x480 pixels per

frame@25 fps

Using the Optional Operating Modes

Mode Icon Description

Delete Last 1 frame

crossed out

Select this mode and press SNAP to delete only the last photo or

video you took. The counter will go down one number.

Delete All 3 frames

crossed out

Select this mode and press SNAP twice to erase the entire memory

contents (the counter resets to zero). Use this after downloading

your les, to clear the memory so you can take new photos. If

"Delete All" is selected accidently, simply wait a few seconds and

the camera will return to normal operation.

Continuous CS Select continuous mode to shoot a rapid series of three photos

instead of a single frame when SNAP is pressed (in normal still

photo mode). This mode automatically cancels after the series of

photos have been shot.

System Requirements

• Operating System: Windows® 2000/ME/XP/Vista/Windows 7 (Windows 98 is not

supported) or Mac OS 9 / OS X

• Internal USB Port

Using the ImageView with Your Computer

1. The camera will be recognized as a USB mass storage device, which means no

special drivers are required for all operating systems later than Windows 98 (Me,

2000, XP, Vista, and Windows 7.) Mac OS 9 and OSX are also compatible.

2. If you have a computer OS as listed above that is USB mass storage compliant,

a new disc icon will appear in Windows Explorer (under “My Computer”) as a

new“Removable Disc”after plugging in the USB cable from the ImageView. Mac

users will see the new "storage device" appear on their desktop. Clicking on

the new disc icon will show the contents, a folder named “DCIM.” The image

folder inside this contains your photos, stored as JPEGs (.jpg le format). They

may then be viewed, edited, renamed and saved using any photo or graphics

software that accepts .jpg les. Videos are recorded in AVI format.

3. After you have copied or opened and saved the photo les to your computers

hard drive, you may disconnect the ImageView camera (NEVER disconnect

the camera while les are still being transferred to your computer). Before

disconnecting, you should“eject”or stop the "removable disc" representing the

camera to avoid an error message (not necessary with Windows XP or later OS).

4. See the following pages for step-by-step instructions on downloading your

photos.

1. Make sure the ImageView is powered on rst (if it is not, it may be recognized as a

"web cam" by your computer). Connect the supplied cable to the ImageView’s USB

port, then directly to a main USB port on your computer-do not use front panel/

keyboard USB ports or unpowered“hubs”.

2. The LCD display will indicate“STO”(if you see "PCC" (PC Camera) instead, unplug the

USB cable, turn the ImageView on rst and try again), and the ImageView will be

recognized as a standard “USB Mass Storage” device. This means that the camera

les can be easily viewed, edited, or copied to your hard drive, just as if they were

stored on an external hard drive or ash drive. (Note for Mac users: the camera will

appear on the Mac desktop as an "Untitled" disk.)

3. (This step is not required with recent Windows operating systems, simply use the

options in the pop-up window to view, copy or edit your photos). Open My Computer

or Windows Explorer. The camera will be seen as a new “Removable Disk” with

an unused drive letter assigned to it. Double click this new “Disk” icon, open

the “DCIM” folder inside, then the folder(s) inside that (“PICT0001.JPG” ,etc). Still

photos are .JPG format, video les are .AVI format. Single clicking any le should

show a small preview image.

4. Click “Edit>Select All” (or click on one photo, contol+click to select multiple

photos), then “Edit>Copy to Folder”(in Windows menus). Select an existing folder

on your hard drive, such as “My Pictures”, or create a new folder (“Football”, etc.),

then click“OK” to transfer copies of the photo les you want.

Transferring Photos/Videos to Your Computer

5. After the photos are transferred to your hard drive, you can disconnect the camera.

Some Windows operating systems may produce a screen warning that you have

disconnected a USB device without stopping or ejecting the “disk” rst (your

photo les will not be harmed). (On Mac computers, drag the “disk” that appeared

on your desktop when the camera was connected into your Trash to “eject” it before

disconnecting.)

6. You’re now ready to open the photo les in any photo editing software. Just use

File>Open and go to the folder where you stored the photos earlier. It is also

possible to open and work with your photos directly from the ImageView while it

is still connected. If you choose to work this way, from a connected camera, be sure

that you save the photo (when you are done editing) to your hard drive, and not the

camera’s memory or card. If you are new to photo editing on a computer, consult

your software’s Help menu for tips on using its features. Along with adjusting the

brightness, contrast, sharpness and color of your photos, you can resize the photo

to t the paper if you are printing, or save a smaller, low or medium resolution

version for email or inserting into documents. When you are ready to save your

edited le, you may want to use“Save As”and give it a more descriptive name than

“PICT___”. Doing this also preserves the original le as a backup to reopen and re-

edit later. Make sure you have successfully transferred all the photos you wanted

to save before using“Delete All” mode to make room for new images.

Otros manuales para ImageView 11-1026

Tabla de contenidos

Otros manuales de Prismáticos de Bushnell

Bushnell

Bushnell Yardage Pro 20-1925 Manual de usuario

Bushnell

Bushnell FUSION X Manual de usuario

Bushnell

Bushnell 91-0203/01-08 Manual de usuario

Bushnell

Bushnell NIGHT WATCH 263230CL Manual de usuario

Bushnell

Bushnell 13-0805 Manual de usuario

Bushnell

Bushnell ImageView 111211 Manual de usuario

Bushnell

Bushnell H2O 157050R Manual de usuario

Bushnell

Bushnell H2O 138005 Manual de usuario

Bushnell

Bushnell Cabelas 20-3125 Manual de usuario

Bushnell

Bushnell 11-0512 Manual de usuario

Bushnell

Bushnell ImageView 118330 Manual de usuario

Bushnell

Bushnell NatureView Manual de usuario

Bushnell

Bushnell Eddie Bauer Manual de usuario

Bushnell

Bushnell IMAGEVIEW HD 118328 Manual de usuario

Bushnell

Bushnell ImageView 11-1026 Manual de usuario

Bushnell

Bushnell Nitro BN1025G Manual de usuario

Bushnell

Bushnell Equinox Z 260501 Manual de usuario

Bushnell

Bushnell 161001CM Manual de usuario

Bushnell

Bushnell 280751 Manual de usuario

Bushnell

Bushnell ImageView 118322 Manual de usuario

Bushnell

Bushnell 260140 Manual de usuario

Bushnell

Bushnell FORGE BF1030T Manual de usuario

Bushnell

Bushnell PowerView 14-1042 Manual de usuario

Bushnell

Bushnell MATCH PRO BMP1556G Manual de usuario

Manuales populares de Prismáticos de otras marcas

Celestron

Celestron VistaPix 72218 Manual de usuario

Levenhuk

Levenhuk Atom Digital DNM200 Manual de usuario

ATN

ATN PS-15 Manual de usuario

Bresser

Bresser TOPAS 7x50 Manual de usuario

Berger & Schroter

Berger & Schroter LN-G3-B50 Manual de usuario

Leica

Leica geovid 8x42 HD-R Manual de usuario

Noblex

Noblex NF 8 x 42 inception Manual de usuario

Newcon Optik

Newcon Optik AN Series Manual de usuario

PHOTONIS

PHOTONIS VYPER Manual de usuario

ATN

ATN 6015-WPT Manual de usuario

Famous Trails

Famous Trails ViewCatcher DCB 822 Manual de usuario

AGM

AGM EXPLORATOR FSB50-640 Manual de usuario

Opticron

Opticron Marine-3 7x50 BIF.GA Guía de instalación

Kayoba

Kayoba 009129 Manual de usuario

Vixen

Vixen ARENA Series Manual de usuario

MAGINON

MAGINON NVB 60 Manual de usuario

Leica

Leica Geovid 56 Manual de usuario

Leica

Leica GEOVID PRO Manual de usuario