Buchi B-290 Guía del usuario

BÜCHI Mini Spray Dryer B-290

Quick Operation Guide

Switch

Aspirator on

Set Inlet temperature,

Switch Heater on

Open

compressed air

Distilled water ready,

start peristaltic pump

Reduce inlet

temp. and/or

increase

pump rate

Increase inlet

temp. and/or

reduce

pump rate

Adjust Nozzle

cleaning

Change from distilled

water to product

Change from product

to distilled water

Inlet Temp. reached

Spray Drying in process

Outlet Temp.

too high

Wet glass

product sticking

Generates the gas stream in the system. 100% re-

commended, so efﬁcient drying and best separation

is obtained.

For aqueous solutions, inlet temperatures are between

100 and 220°C. Lower range for heat sensitive product.

Typical set point 150°C.

By opening the needle valve on the ﬂow control, the

compressed air for the feed dispersion is set. Typical

level is 4 cm (approx. 600 l/h).

Close peristaltic pump bed. The process is started

with pure water to get the drying conditions . The outlet

temp. will decrease due to the consumption of energy

by the evaporation.

Typical set point of pump 30%.

The outlet temp. deﬁnes the maximal thermal load for

the product. Adjust inlet temp. and pump rate to obtain

a certain outlet temp. Lowering the aspirator rate will

also decrease the outlet temp.

In case of suspensions or product which tend to clog

the nozzle, the nozzle cleaning is switched on. Higher

number (2-9) means more cleaning pushes.

The spray drying starts as soon as the tube is switched

from pure water to product (by feed switch valve or

manually). The outlet temp. will slightly increase becau-

se less water has to be evaporated, eventually adjust

inlet temp.

Switch back to pure water to clean tube and nozzle.

Additional cleaning effect by drawing air bubbles.

BÜCHI Mini Spray Dryer B-290/

BÜCHI Inert Loop B-295

Quick Operation Guide

Switch instrument on,

switch aspirator on

Set cooling temperature

on Inert Loop B-295

Feed nitrogen be opening

spray ﬂow valve

Heater and feeding ready

to be started

Start with

pure solvent

Adjust Nozzle

cleaning

Change from pure

solvent to product

Change to

pure solvent

O2 level <6% is reached

Spray Drying in process

Temperatures constant

Solvent

recovery

Inert Loop starts to cool, both signal lamps are on (after

20 sec.). When starting the aspirator, pressure signal

lights off: gas stream is circulating. 100% recommen-

ded for efﬁcient drying and best separation in cyclone.

The set cooling temperature depends upon the solvent

used. For boiling point <70°, -20° is recommended, for

pure water, 10° must not be fallen below.

Nitrogen is fed into the cycle and the same volume is

leaving the system by the exhaust tube. The level of

oxygen is decreasing. If not, check tightness to ﬁnd

leakage.

The system is now under inert condi-tions; heater is

started. The procedure is equal as on the back side.

Inlet temp. approx. + 10°C above boiling point of sol-

vent.

Pure solvent is used to get the drying conditions. High-

er pump rates can be used, typical set point is 60%.

In case of suspensions or product which tend to clog

the nozzle, the nozzle cleaning is switched on. Higher

number (2-9) means more cleaning pushes.

The spray drying starts as soon as the tube is swit-

ched from solvent to product (by feed switch valve or

manually).

At the end of the process, switch back to pure solvent

to clean tube and nozzle. Additional cleaning effect by

air bubbles.

Empty receiving bottle in Inert Loop B-295.

www.buchi.comBÜCHI Labortechnik AG 96974 0904 300

Otros manuales para B-290

Otros manuales de Equipo de laboratorio de Buchi

Buchi

Buchi KjelDigester K-446 Manual de usuario

Buchi

Buchi K-355 Manual de usuario

Buchi

Buchi S-300 Manual de usuario

Buchi

Buchi C-660 Manual de usuario

Buchi

Buchi Lyovapor L-200 Manual de usuario

Buchi

Buchi S-300 Manual de usuario

Buchi

Buchi Rotavapor R-100 Manual de usuario

Buchi

Buchi Pure C-805 Manual de usuario

Buchi

Buchi K-437 Manual de usuario

Buchi

Buchi Pure C-805 Manual de usuario

Buchi

Buchi Pure Chromatography C-900 Manual de usuario

Buchi

Buchi B-820 Manual de usuario

Buchi

Buchi HydrolEx H-506 Manual de usuario

Buchi

Buchi K-365 Dist Line Manual de usuario

Buchi

Buchi X-Sential Manual de usuario

Buchi

Buchi NIRMaster Manual de usuario

Buchi

Buchi Pure C-810 Manual de usuario

Buchi

Buchi NIRMaster Essential Manual de usuario

Buchi

Buchi Melting Point M-560 Manual de usuario

Buchi

Buchi SpeedDigester K-425 Manual de usuario

Buchi

Buchi SpeedExtractor E-914 Manual de usuario

Buchi

Buchi Syncore Manual de usuario

Buchi

Buchi SpeedExtractor E-916 Manual de usuario

Buchi

Buchi Scrubber K-415 Manual de usuario

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario