Brother SDX900 Manual de usuario

Wireless Network Setup Guide

Cutting Machine

Product Code: 893-Z05/Z09

Trademarks

WPA™ and WPA2™ are trademarks of Wi-Fi Alliance®.

Compilation and Publication

Under the supervision of Brother Industries, Ltd., this manual has been compiled and published, covering the

latest product descriptions and specifications.

The contents of this manual and the specifications of this product are subject to change without notice.

Brother reserves the right to make changes without notice in the specifications and materials contained herein

and shall not be responsible for any damages (including consequential) caused by reliance on the materials

presented, including but not limited to typographical and other errors relating to the publication.

This product includes software developed by the following vendors:

Thank you for purchasing this cutting machine.

This guide provides setup instructions so that you can use a wireless network to send data created in

CanvasWorkspace to your cutting machine (hereafter referred to as “machine”) as well as save data that you

have edited on your machine to CanvasWorkspace. Carefully read the instructions in this guide and complete

the setup to easily transfer data without the need for any device such as a USB flash drive.

Before using this machine, carefully read the “IMPORTANT SAFETY INSTRUCTIONS” in “Product Safety

Guide”.

For basic operations of your machine, refer to “Operation Manual”. The Operation Manual can be downloaded

from <http://s.brother/cmoae/>.

For information on the operations of CanvasWorkspace, refer to the “Help” menu in CanvasWorkspace.

In addition, after you have finished reading this guide, store it where it can quickly be accessed for future

reference.

With this function, patterns edited in the dedicated application CanvasWorkspace can be transferred to the

machine via a wireless network connection.

For details on transferring pattern data, refer to the Operation Manual.

aWireless network access point/router

bComputer connected to wireless network access point/router

cYour machine

dCanvasWorkspace server

Perform the setup with the following steps.

aSet up Wireless Network Connection

bLogin to CanvasWorkspace Internet version.

• In order to use CanvasWorkspace, a CanvasWorkspace (formerly ScanNCutCanvas) Login ID is necessary. If you do

not have a free account, go to <http://CanvasWorkspace.Brother.com> to create a new account.

cRegister machine under CanvasWorkspace.

INTRODUCTION

Transfer Data Using Wireless LAN

INTRODUCTION ......................................................................................................................... 1

Transfer Data Using Wireless LAN ............................................................................................... 1

Quick Wireless Network Setup Instructions ................................................................................. 3

Connect Machine to a Wireless Network ..................................................................................... 6

Activate the Wireless Network .................................................................................................................................. 6

Set up the Wireless Network..................................................................................................................................... 6

Check the Wireless Network Setup/Status............................................................................................................... 9

Using the “Others” Menu .......................................................................................................................................... 9

Register Machine Under CanvasWorkspace ............................................................................... 10

Troubleshooting.......................................................................................................................... 13

How can I find the wireless security information (Network Name (SSID) and Network Password) ........................ 13

Error codes/Error messages ................................................................................................................................... 13

CONTENTS

For quick and easy instructions on how to set up your wireless network, please follow the steps below.

For more detailed setup procedure, please refer to page 6, and if a connection is not established correctly and

an error message appears, see “Error codes/Error messages” on page 13.

■Requirements for the wireless network

connection

The wireless network connection complies with IEEE

802.11 n/g/b standards and uses the 2.4 GHz frequency.

The Wireless Network Name (SSID) and Password

(KEY)* for your wireless access point/router are required

to connect your machine to a wireless network.

Find this information and note it first.

Make sure that you have the right password and note

some password are case (upper case & lower case)

sensitive.

* Your network name selection should match the

wireless network that your PC or mobile device is

connected.

aTurn on the machine.

When the following message appears, touch the

“OK” key.

bTouch in the home screen.

cSelect “ON” for “WLAN Enable”.

dUnder “Network” settings screen as shown

below, touch “Setup Wizard”.

Available Network Name (SSID) will be

displayed.

For step e& fplease refer to “Requirements for

the wireless network connection” before step a.

You'll need your Wireless Network Name (SSID) and

Network Password (Network Key).

eSelect your Network Name (SSID), and then

touch the “OK” key.

fType in the Network Password (Key), and then

touch the “OK” key.

Quick Wireless Network Setup Instructions

Network Name (SSID) Network Password

(Network Key)

gWhen the message shown below appears, touch

the “Yes” key.

hWhen a connection is established, the following

message appears, touch the “Next” key.

iOnce you have completed reading the message

appears on the following screen, touch the

“Next” key.

jAfter the following screen, describing how to

obtain the PIN code, appears, leave the screen

displayed, and then continue with the following

operation using CanvasWorkspace Internet

version.

aMachine number

kOpen CanvasWorkspace Internet version

(http://CanvasWorkspace.Brother.com) on

your computer and then log in.

Note

• First time users should obtain a free account.

• If you already have an account with

CanvasWorkspace (formerly

ScanNCutCanvas), you can use the same login

ID and password to login.

lClick in the upper-right corner of the screen.

The page for managing your account appears.

mClick “Machine(s) Registration”.

nClick “Register a New Machine”.

oType in your machine number, and then click

the “OK”.

Memo

• Your machine number appears on your

machine in the screen shown in step j

describing how to obtain the PIN code.

pNote the four-digit PIN code that appears on

the screen.

qGo back to your machine's screen and then

touch the “OK” key.

The PIN code input screen appears.

rType in the four-digit PIN code that appeared

in the CanvasWorkspace screen, and then

touch the “OK” key.

sTouch the “OK” key.

The account registration screen appears.

Touch twice to go back to the home

screen.

The Wireless network connection has completed!

Now, you can start transfer the data between your

cutting machine and CanvasWorkspace via a wireless

network connection. For details on transferring the

data, refer to Operation Manual.

The following procedures are detailed information for network settings.

Activate the Wireless Network

aTurn on the machine.

When the following message appears, touch the

“OK” key.

bTouch in the home screen.

The network settings screen appears.

Memo

• Another way to access the “Network” menu is

to click located at the bottom of the home

screen.

cSelect “ON” for “WLAN Enable”.

Your machine will begin to emit the wireless

network signal.

Memo

• Another way to turn “ON” the “WLAN Enable” is

by selecting “Yes” when the message below

appears in the “Setup Wizard”.

Set up the Wireless Network

Wireless LAN connection can be set up by using the

wizard (recommended) or alternative method.

■Requirements for the wireless network

connection

The wireless network connection complies with IEEE

802.11 n/g/b standards and uses the 2.4 GHz frequency.

Memo

• A wireless network cannot be set up with WPA/

WPA2 Enterprise. For the authentication

methods your machine supports, see “Err-03”

on page 14.

■Connect Using Setup Wizard

(Recommended)

aThe Wireless Network Name (SSID) & Network

Password (KEY)* are required to connect your

machine to a wireless network.

* Network Password is also described as the

Network Key, Security Key, or Encryption Key.

Connect Machine to a Wireless Network

Network Name (SSID) Network Password

(Network Key)

Note

• If you do not know this information (Network

Name (SSID) and Network Password (Key)), you

cannot continue the wireless setup.

• How can I find this information?

1) You should see the documentation provided

with your wireless access point/router.

2) The default Network Name (SSID) could be

the manufacturer’s name or the model

name.

3) If you do not know the security information,

please consult the router manufacturer, your

system administrator, or internet provider.

4) Some Wireless Network Name (SSID) and

Network Password (Key) are case (upper

case and lower case) sensitive. Please

properly record your information.

bTouch in the home screen.

The network settings screen appears.

Memo

• Another way to access the “Network” menu is

to click located at the bottom of the home

screen.

cUnder “Network” settings screen as shown

below, touch “Setup Wizard”.

Available Network Name (SSID) will be

displayed.

dSelect your Network Name (SSID), and then

touch the “OK” key.

The screen for entering the Network Password

(Key) appears.

Note

• If the desired Network Name (SSID) is not

displayed, specify it as described below.

1) Select “[New SSID]”, and then touch the

“OK” key.

* “[New SSID]” appears at the bottom of the

list of detected SSIDs.

2) Type in the desired Network Name (SSID),

and then touch the “OK” key.

3) Specify the authentication method and

encryption mode and then touch the “OK”

key.

Memo

• appears beside a previously connected

network from the list of available networks.

Since the Network Password (Key) has been

saved for the network beside , a connection

to that network can be re-established without

having to re-enter the connection information

(Network Password, etc.).

• The previously entered Network Password

(Key) for a maximum of 12 connections are

saved with “[Saved SSID]”. Touch the “[Saved

SSID]” key to display the connection

information.

eType in the Network Password (Key) noted in

step a, and then touch the “OK” key.

aCharacter input display

bCharacter keys

cUppercase/lowercase selection key

dSpace key

eLetter/number/special character selection key

fBackspace key (Deletes the character at the

cursor’s position.)

gCursor keys (Move the cursor to the left or

right.)

fWhen the message shown below appears, touch

the “Yes” key.

The following screen appears when a connection

is established.

Touch the “Next” key, and then continue with

“Register Machine Under CanvasWorkspace” on

page 10.

Memo

• If you have already completed the machine

registration under CanvasWorkspace, the

following screen appears. Touch the “OK” key

to complete the wireless network setup.

Note

• If a connection was not successfully

established:

- If the message “Wrong Network Key: Err-04”

appeared, the Network Password (Key) may

have been entered incorrectly. Touch the

“OK” key, and then repeat the procedure

from step cof “Connect Using Setup

Wizard (Recommended)” on page 6.

- For details on other causes, see “Error

codes/Error messages” on page 13.

• While connected, the strength of the signal is

indicated by the blue icon in the upper-

left corner of screens such as the home screen.

• After your wireless network has been set up,

your machine will connect to the wireless

network each time the machine is turned on.

However, “WLAN Enable” in the network

settings screen must remain set to “ON”.

■Connect Using “WLAN Assistant

Wizard” (WAW).

The wireless network can be set up using the dedicated

application “WLAN Assistant Wizard” (WAW).

Download the application from

http://s.brother/cuoad/, and then follow the instructions

that appear in the computer screen in order to complete

the setup.

After a connection is established, touch the “Next” key,

and then continue with “Register Machine Under

CanvasWorkspace” on page 10.

:Strong signal

:Medium signal

:Weak signal

:No signal

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cortador de Brother

Brother

Brother DesignNCut DC200 Manual de usuario

Brother

Brother 891-Z05 Manual de usuario

Brother

Brother EF4-N11 Manual de usuario

Brother

Brother 891-Z02 Manual de usuario

Brother

Brother DesignNCut DC200 Dimensiones

Brother

Brother CM100DM Manual de usuario

Brother

Brother 891-Z02 Manual de usuario

Brother

Brother ScanNCut DX Series Manual de usuario

Brother

Brother 891-Z01 Manual de usuario

Brother

Brother ScanNCut DX Manual de usuario

Brother

Brother SDX325 Manual de usuario

Brother

Brother 891-Z08 Manual de usuario

Brother

Brother 891-Z05 Manual de usuario

Brother

Brother ScanNCut2 Manual de usuario

Brother

Brother 891-Z01 Instrucciones de instalación y funcionamiento

Brother

Brother SDX230DX Manual de usuario

Brother

Brother TD-4420TN Manual de usuario

Manuales populares de Cortador de otras marcas

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Manual de usuario

Makita

Makita DCS552 Manual de usuario

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Manual de usuario

Makita

Makita 4112HS Manual de usuario

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Manual de usuario

Hitachi

Hitachi CM 4SB2 Guía de solución de problemas

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Manual de usuario

GCC Technologies

GCC Technologies AFJ-24S Manual de usuario

DeWalt

DeWalt XR LI-ION DCS350N Manual de usuario

Baudat

Baudat ES1 Manual de usuario

Mafell

Mafell ZAF 200 Guía

Makita

Makita 4100NH Manual de usuario

Formax

Formax FD 574 Manual de usuario

EINHELL

EINHELL TE-MA 1500 Manual de usuario

Husqvarna

Husqvarna Cut-n-Break K 760 Manual de usuario

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Manual de usuario

TRI tool

TRI tool 301A Manual de usuario

Roller

Roller King 1 1/4 Manual de usuario