Broadata Link Bridge LBC-HDMI-T-WP Manual de usuario
LBC-HDMI-T/R-WP
LINK BRIDGETM HDMI WALL PLATE
HDBASETTRANSMISSION SYSTEM
BCI reserves the right to make changes to the products described herein without prior
notice or consent. No liability is assumed as a result of their use or application. All
rightsreserved.
©2013 Broadata Communications, Inc.
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMI WallPlateHDBaseTTransmissionSystem
SAFETY INSTRUCTIONS AND
COMPLIANCE DECLARATIONS
PLEASE OBSERVE THE FOLLOWING SAFETY
PRECAUTIONS
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMIWallPlate HDBaseTTransmissionSystem
Broadata Technical Support, (800) 214-0222
4
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION ..............................................5
2.0 SETUP..............................................................................8
2.1 MOUNTING.......................................................................8
2.2 CABLING AND CONNECTORS.......................................8
2.3 HDMI VIDEO INTERFACE................................................9
2.4 CAT-5E/6 TRANSMISSION CONNECTION ...................10
3.0 DC POWER CONNECTION...........................................11
3.1 IN-WALL POWER/CAT-5E/6 WIRING INSTRUCTION ..12
4.0 MAINTENANCE AND TROUBLESHOOTING ...............14
4.1 MAINTENANCE ..............................................................14
4.2 TROUBLESHOOTING ...................................................14
5.0 SPECIFICATIONS...........................................................16
6.0 SERVICE PROCEDURE ................................................17
6.1 REPLACEMENT POLICY ..............................................17
6.2 RETURN AND REPAIR SERVICE .................................17
7.0 LIMITED WARRANTY ....................................................18
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMI WallPlateHDBaseTTransmissionSystem
1.0 PRODUCT DESCRIPTION
TheLBC-HDMI-T/R-WPtransmitter and receiverisa high performance,
lowcost,miniature,LinkBridgeTMHDBaseTHDMITransmissionSystem.
It carries one (1) unidirectional HDMI video with embedded audio. This
uniqueCAT-5e/6 transmissionsystem letsyourdigitalflat panel display
extendupto 70m (230ft)at 4K2KandWUXGA(1920x1200 @60Hz)or
720p/1080i/1080pHDTV videoresolution.
LBC-HDMI-T/R-WP is a 1 gang single-input Decora style wall plate
transmitterandreceiver.When the HDMIwith activesignalisconnected,
thesignalwillbesent to the compatibleHDBaseTreceiver automatically.
Inaddition,theLBC-HDMI-T/R-WPsupportsPoH(PoweroverHDBaseT)
where they can be powered by a remote Matrix, a compatible receiver/
transmitter or local DC adapter.
In addition, the LBC-HDMI-T/R-WP transmitter and receiver are
compatible with our Designer and Standard (LBH & LBC model) Series
transmittersandreceivers.Thismakes both CAT-5e/6transmission and
HDMI/DVI/VGA/YPbPrIconversioninonesinglesystemsetup.Theunits
are easily monitored by a power/ link LED indicator. Figures 1-1, and
1-2 illustrate the front and rear panels of the LBC-HDMI-T/R-WP unit.
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMIWallPlate HDBaseTTransmissionSystem
Broadata Technical Support, (800) 214-0222
6
Front Panel (Wall Plate)
1. Link:Soildredwhen power up.Blinkingred/amberwhen HDBT
connectwithoutvideosignal.Solidamberwhenvideoconnection
established.
2. HDMI In: Connect to HDMI source for Tx unit and connect to
display for Rx unit.
Figure 1-1
LBC-HDMI-T/R-WP Front Panel
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMI WallPlateHDBaseTTransmissionSystem
Rear Panel (Wall Plate)
1. Power: Connect to 24V DC adapter here to power up device.
2. HDBaseT: Connect RJ45 category cable from HDBaseT
transmitter to receiver.
Figure 1-2
LBC-HDMI-T/R-WP Rear Panel
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMIWallPlate HDBaseTTransmissionSystem
Broadata Technical Support, (800) 214-0222
8
2.0 SETUP
The BCI LBC HDBaseT Extender Series units are used in pairs. One
LBC-HDMI-T-WP transmitter unit is located at the near-end (source)
andconnectedthrough a singlecategorycable, to theLBC-HDMI-T-WP
receiver shown below and located at the far-end (sink) of the link.
Figure2-1 depictsa typical installation forthe LBC-HDMI-T/R-WPpair.
2.1 Mounting
Beforeinstalling theunits into your housing, make sure there is
enoughspacetopullandconnectboththeelectricalandcategory
cables without stressing them beyond the manufacturer’s
limitations (also known as the minimum bend radius).
2.2 Cabling and Connectors
In order to setup the LBC-HDMI-T/R-WP properly, make sure
toobserve thefollowing instructionswhen installingthe proper
cables. The LBC-HDMI-T/R-WP requires two parts to the
cablingsetup,thevideosignalandthetransmission connections.
Figure 2-1
LBC-HDMI-T-WP with LBC-HDMI-R-WP Transmission Pair
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMI WallPlateHDBaseTTransmissionSystem
2.3 HDMI Video Interface
The HDMI video connection is the HDMI plug connectors for
video input port. Use the following instructions to properly
connect your component video as illustrated in Figure 2-2.
Connectthe LBC-HDMI-T/R-WP(Transmitter/Receiver) unit’s
HDMI video source and video output to the user’s display with
the appropriate HDMI cables.
Figure 2-2
Video Connection User’s HDMI Video Source and Display
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMIWallPlate HDBaseTTransmissionSystem
Broadata Technical Support, (800) 214-0222
10
2.4 CAT-5e/6 Transmission Connection
Select an appropriate terminated shielded CAT 5e/6 cable.
Each unit’s RJ45 ports in the system are specified for use with
RJ45connectors. Follow the ensuing instructionson installing
andconnecting theHDBaseT links:
1. Ensurethepower is offbefore proceeding withtheCAT-5e/6
cableinstallation.
2. Connect thecable from one unit to the other connecting the
near end LBC-HDMI-T-WP unit’s RJ45 port and to the far
end of the LBC-HDMI-R-WP (use any compatible LBC or
LBH series receiver) unit’s RJ45 RX port as illustrated in
Figure 2-3.
Figure 2-3
CAT-5e/6 Connection
LBC-HDMI-T/R-WPUser’sManual
LinkBridgeTM HDMI WallPlateHDBaseTTransmissionSystem
3.0 DC POWER CONNECTION
Congratulations!Youare nowreadytopoweruptheLBC-HDMI-T/R-WP
and set up your network connection. In order to make sure that you
have a proper installation, please observe the following:
1. Your AC jack has power.
2. The 24VDC power supply is working.
3. Yourelectrical systemhas proper grounding(this ensuresthat
your power supply does not suffer from voltage variations).
4. Power Surge Protection. This is optional, but highly
recommended.A UPS system provides voltage regularity as
well as prevents spikes from occurring, thus protecting your
LBH-HDMI-T/R-WPfrom sensitive voltage conditions.
TheLBC-HDMI-T/R-WP derivespower froman external 24VDC power
supply or via PoH (Power over HDBaseT). This power supply is a wall
mountedAC/DCadapter,100-240 VAC,50-60 Hz,at 1.0A.This power
supply comes standard for the LBC-HDMI-T/R-WP unless otherwise
specified. To provide power to the LBC-H/V-T-WP, simply connect the
power cord, already provided with the units, and connect it to the wall
jack. (You will find one power cord per unit). Once the power cord has
beenconnected tothe wall jack,connect 24VDCto the unitand theunit
should power up immediately. If you have any problems or concerns,
regarding the installation, make sure that you have taken the proper
steps to ensure a proper power connection. Otherwise, feel free to
contact us for any questions you may have.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Receptor de Broadata
