BrandMotion AVMS-3604 Manual de usuario
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 1 of 9
2012-2014 F-150 4” MyFord factory display
360º Vision System
(Kit # AVMS-3604)
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
Tools & Supplies Needed:
Video interface for 4” MyFord display
2004-2014 Tailgate handle w/camera
360º camera module
Key box power/image buttons
Front camera w/grill mount and harness
2 side mount cameras w/pods and harnesses
2 video output RCA cables
Power/camera input harness
2 side camera templates
Mounting screws and gaskets
These instructions
Wire strippers
Wire cutters
Electrical tape
Zip ties
Plastic panel removal tools
Screwdriver
7 mm socket
Drill
Large Uni-bit/drill bits
Hole saws
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
Section 1:
Front camera installation
1. Front camera is mounted in the grill below
the Ford emblem.
2. Mount camera in housing using the bracket
and screws provided.
3. Mount the housing using the provided
screws to the grill and putting the caps in
the holes to close them.
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 2 of 9
4. Run the camera harness along the under
hood covering, down the drive side hinge.
Zip tie the harness to the hinge so the
harness will not kink or cut.
5. Run harness into the vehicle though the
factory grommet in the drivers side firewall.
6. Route the camera harness to the location of
the 360º module.
Section 2:
Side Mirror Camera installation
1. The inter door panel will have to be
removed for installation of the side
cameras.
2. Working on the driver side door. With the
door closed, place the template sticker
(
marked LHD
) on the bottom side of the
mirror with arrow aiming away from the
vehicle. Perpendicular to the side of the
body. (
Do not go by mirror lines or angles
.)
3. Make sure the template is to at least the
middle to outer edge of the mirror. (
The
camera needs to see only a little of the side
of the vehicle and mainly the ground and
objects next to the vehicle
.)
4. Remove the door panel and the 3 nuts that
are holding the mirror to the vehicle.
5. Place the mirror on a soft or padded surface
and remove the glass from the mirror.
(
Each vehicle is different, but most are
mounted by a center circle and will unclip
from it
.)
6. After the glass is removed, check to see if
where the templates are placed there is
clearance for the camera and will not cut
into anything in the mirror housing. (
If the
template has to be moved make sure to
keep the arrow aiming the same way
.)
7. Drill a hole in the bottom of the mirror using
a hole saw or Uni-bit to the size on the
template. Which is 1 1/8”
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 3 of 9
8. With the sticker still in place, drill the (2)
mounting screw holes with a 1/16 drill bit.
(
Do not go all the way though
.)
9. The side cameras, brackets and pods are
labeled for right-RH and left-LH. Make sure
to assemble them correctly. Use caution not
to loss the tiny screws to mount the
cameras to the brackets and the brackets to
the pods.
10. Using the LH camera assembly, attach the
foam gasket to the bottom side of the pod,
lining up the notch in the foam with the
bump on the pod.
11. Remove the tape from the foam gasket and
mount the camera pod to the mirror. Use
the self tapping screws provided to mount
the pods to the underside of the mirror. (
Do
not over tighten the screws, it may strip out
the plastic.)
12. Route the camera cable though the mirror
and out of the mounting side of the mirror.
Make sure not to block any movement of
the mirror glass or folding.
13. Route the cable in the door and remount
the mirror to the vehicle.
14.
You will next pin the camera cable wires
into the provided connecter. Inset the pins
into the connecter until they make a “snap”
sound. Use the left side camera harness to
match up where the pin locations are.
(See
Diagram chart 1a. at end of instructions for
all camera pin connections.)
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 4 of 9
15.
Attach the camera cable to the harness and
route though the door to the rubber boot.
Secure the harness to the factory wire
harness with zip ties.
16.
Route the harness out though the rubber
boot into the vehicle. (
The vehicle might
have a Molex or plastic plug in the door of
body, if so drill a hole in the plug if there is
any room to, if not drill a hole lower in the
door jus under the rubber boot and the
same if the plug is in the body. Grommet
and seal any holes that might be drilled.)
17.
Route the harness to the 360º module.
18.
Reinstall the mirror glass into the mirror and
reinstall the door panel.
19.
Repeat the process on the passenger side
door and then continue to the next section.
Section 3:
Rear camera installation
1. The rear camera on this vehicle will be in
the tailgate handle. The camera is already
mounted to the handle.
2. Remove the trim panel on the backside of
the tailgate, by removing the Torx screws
holding it in place.
3. Unclip the latch rods the go to the handle.
(
If equipped with a rear camera, unplug it
from the harness.)
4. Loosen the (2) 10 mm nuts holding the
handle in place.
5. Remove the handle and install the new
handle with the 360º camera installed.
6. Connect the camera cable to the rear
camera harness and heat shrink or tape the
connection.
7. Route the harness through the tailgate and
into the lower bed frame. (
If holes do not
exist in the tailgate or bed frame you must
drill new holes in to each to run harness.
Make sure to use grommets and seal up
holes to prevent rust or cutting of harness.)
8. Route the harness on the underside of the
vehicle. Use zip ties to hold harness in place
and be careful to avoid any moving parts or
exhaust.
9. Route the harness in to the vehicle by
coming up though a grommet in the floor or
the grommet under the hood in the firewall.
10. Route the rear camera harness to the 360º
module.
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 5 of 9
Section 4:
360º module installation
1. Connect the correct camera plugs to the
360º module. Front, rear, left side, right
side, CVBS and CVBS RV.
2. The CVRS output, is video output controlled
by the power on/off button to the system. It
is connected to the video input on the
mirror or AUX video on the interface.
3. The CVRS RV output, is video output when
the accessory is powered on. It is
connected to the camera input on the
mirror or camera input on the interface.
4. If not done so yet connect the power
harness to the 360º module. Wire up the
power connections, yellow is constant, red
is accessory, black is ground, blue is
reverse.
5. Do not mount the 360º module, you will
need to get to it for calibration of the
cameras.
6. Plug in the Key Box and mount to the right
side of the steering column on the das trim
with the tape provided.
7. To turn on the system press the power
button on the Key Box. To change camera
views press the car image button. A long
press will show a full front view another
long press will show a full rear view.
8. Place the vehicle into reverse to see the
rear camera image on the screen.
Section 5:
Installation of the 4” MyFord interface
1. Remove dash trim around screen/display in
dash.
2. Remove the (4) 7mm screws holding the
screen into the dash.
3. Remove the screen from the dash.
4. Check compatibility of screen/display on the
last page of this install guide.
5. Remove the 6-pin connector from the
harness, if connected, then plug the
harness into the 6-pin connector on the
9002-2780 module included in this kit.
6. Connect the 12-pin power output and
camera input harness to the 9002-2780
module.
7. Disconnect the FCDIM/display harness on
the back of the display by pushing down
on the tab and pulling the “lever” back.
8. Connect the T-harness into the FCDIM first
from the 9002-2780.
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 6 of 9
9. Then connect the opposite end to the
vehicle harness, within 5 seconds turn the
key to the run/ignition position. (Do not
start the vehicle)
10. With module connected to vehicle specific
T-Harness, and display connected, power
vehicle on to IGN (Do not start vehicle).
11. With vehicle ignition turned on and radio
display on and connected, connect the two
jumper wires together. This will initiate the
programming procedure.
12. Within 10 seconds radio display should
display “Diagnostics mode” and shut off.
Radio display will turn back on, and should
shut off one more time. Once radio and
display have shut down twice and came
back on, programming is complete. The
entire process should take less than two
minutes.
13. If the programming does not work
successfully, disconnect module power,
verify the dip switch settings, reconnect
module, turn the vehicle off and then on
again, and try again.
14. Disconnect and isolate the jumper wires to
prevent accidental programming.
15. Test programming by placing the vehicle in
reverse. (Testing without a camera will
result in a “camera not available” message
and disable the camera input temporarily.
16. Mount module to top of radio/cd case in
dash, behind screen.
Important Notes:
•If Camera is tested before camera is
powered and connected, system
must be fully shut down and turned
back on before camera will work
again.
•Depending on vehicle configuration,
display may stay in reverse camera
mode until vehicle is driven to a pre-
determined speed. This is a
factory function.
•Some displays will show a
magnifying glass (zoom) icon on the
display. This is meant to be used
with an OEM Camera with zoom
function. It is not compatible with
any aftermarket cameras and cannot
be disabled.
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 7 of 9
Unprogramming/Reset to factory
This module can be used to return the
vehicle to factory in the case the customer wants it
uninstalled. Once this is complete the module can
then be used on another VIN. Until the unprogram
routine is run, the module is locked to the VIN of
the vehicle it is currently installed in.
To unprogram the vehicle, disconnect the
module, set the DIP switches to the corresponding
“Unprogram” profile, reconnect the module and
wait for the display to reset twice the same as in
the programming procedure.
Find the part number on the back of the display and verify compatibility.
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 8 of 9
! INSTALLATION!INSTRUCTIONS!
AVMS-3604.doc Page 9 of 9
The dip switches should be set as follows:
10010!
MyFord/MyFord Touch
1-UP/ON
2-DOWN/OFF
3-DOWN/OFF
4-UP/ON
5-DOWN/OFF
6-DOWN/OFF
Tabla de contenidos
Otros manuales de Electrónica del automóvil de BrandMotion
BrandMotion
BrandMotion Curb Alert Park View Pro 5000-CA6 Manual de usuario
BrandMotion
BrandMotion 5000-CA14 Manual de usuario
BrandMotion
BrandMotion FLTW-7617 Manual de usuario
BrandMotion
BrandMotion AVMS-3700v3 Manual de usuario
BrandMotion
BrandMotion ADAS-1000 Manual de usuario
BrandMotion
BrandMotion 9002-2738 Manual de usuario
BrandMotion
BrandMotion AHDS-7810v2 Manual de usuario
