BOSSCO Modulation MD-200 Manual de usuario

Owner’s Manual

Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (the leaet “USING THE UNIT SAFELY”and the Owner’s

Manual (p. 19)). After reading, keep the document(s) where it will be available for immediate reference.

Panel Descriptions

Top Panel

1 2 3 4

5 6

7 8 9 10

11 12

1 Display

Shows the parameters and the values.

2 [RATE] knob

Adjusts the speed at which the eect sound changes.

Each time you press the button, the rate indication

switches.

Frequency #Tempo (BPM)

Example indications

0.01 Hz = “0.01”, 1 Hz = “1.00”, 10 Hz = “10.0”,

tempo: 120 = “120.”, tempo: 1000 = “1.0K.”,

tempo: 10000 = “10K.”

* When the mode is ROTARY, this switches the speaker’s rotation

speed between SLW (slow) and FST (fast).

3 [DEPTH] knob

Adjusts the depth to which the eect sound is

modulated.

* When the mode is ROTARY, this adjusts the amount of preamp

distortion. When the mode is SLICER, this adjusts the balance

between the eect sound and the direct sound.

Panel Descriptions

4 [E. LEVEL] knob

Adjusts the volume of the eect sound.

In some modes, this adjusts the balance between eect

sound and direct sound.

5 Mode knob

Selects the eect.

Mode Explanation

CHORUS (CHO)Chorus sound using cutting-edge BOSS

technology.

CE-1 CHORUS (CE1)A chorus sound that models the CE-1.

FLANGER (FLG)Produces a anging eect.

PHASER (PHS)Produces a phase eect.

Mode Explanation

VINTAGE PHASER

(VPH)

Models the MXR PHASE90 produced

during the 1970s.

CLASSIC VIBE (CVB)Models the Uni-Vibe.

VIBRATO (VIB)Vibrato with a unique eect.

TREMOLO (TRM)An eect that cyclically changes the

volume.

ROTARY (ROT)Realistically reproduces the sound of a

rotary speaker.

AUTO WAH (AWH)Cyclically modulates a lter to

automatically create a wah eect.

SLICER (SLI)Cyclically cuts the sound to create a

variety of slice patterns.

OVERTONE (OVT)

Adds new overtones to create

resonance and depth not present in

the original sound.

6 PARAM [1]–[3] knob

Set the parameters. The parameters dier depending on the mode.

Mode PARAM 1 PARAM 2 PARAM 3

CHORUS (CHO)

SWT (SWEETNESS)

Higher values create a more

enveloping sound.

LOC (LOW CUT FREQUENCY)

Adjusts the tonal character of the

low-frequency region.

HIC (HIGH CUT FREQUENCY)

Adjusts the tonal character of the

high-frequency region.

CE-1 CHORUS (CE1)

TYP (TYPE)

CHO:Chorus sound of the CE-1

VIB:Vibrato sound of the CE-1

LO (LOW LEVEL)

Adjusts the tonal character of the

low-frequency region.

HI (HIGH LEVEL)

Adjusts the tonal character of the

high-frequency region.

Panel Descriptions

Mode PARAM 1 PARAM 2 PARAM 3

FLANGER (FLG)

RES (RESONANCE)

Adjusts the amount of resonance

(feedback).

MAN (MANUAL)

Adjusts the center frequency at

which the eect is applied.

LOC (LOW CUT FREQUENCY)

Cuts the frequency components

below the specied frequency.

With the FLT (at) setting, the low

cut lter is not applied.

PHASER (PHS)

RES (RESONANCE)

Adjusts the amount of resonance

(feedback).

MAN (MANUAL)

Adjusts the center frequency at

which the eect is applied.

LOC (LOW CUT FREQUENCY)

Cuts the frequency components

below the specied frequency.

With the FLT (at) setting, the low

cut lter is not applied.

VINTAGE PHASER

(VPH)

TYP (TYPE)

THR (THRU): Only phaser sound.

CRH (CRUNCH): Distortion is added.

DRV (DRIVE)

Adjusts the amount of distortion

when CRH (CRUNCH) is selected.

TON (TONE)

Adjusts the tonal character when

CRH (CRUNCH) is selected.

CLASSIC VIBE (CVB)

TYP (TYPE)

THR (THRU): Only phaser sound.

FUZ (FUZZ): Distortion is added.

DRV (DRIVE)

Adjusts the amount of distortion

when FUZ (FUZZ) is selected.

TON (TONE)

Adjusts the tonal character when

FUZ (FUZZ) is selected.

VIBRATO (VIB)

TON (TONE)

Higher values produce more

complex modulation.

D/E (DIRECT/EFFECT BALANCE)

Adjusts the volume of the direct

sound and the eect sound.

TON (TONE)

Adjusts the tonal character.

Panel Descriptions

Mode PARAM 1 PARAM 2 PARAM 3

TREMOLO (TRM)

TYP (TYPE)

TRM (TREMOLO): Cyclically modulates

the volume.

PAN (PAN): By alternately changing

the volume of left and right, this

produces the impression that the

sound is moving between the left

and right speakers when heard in

stereo. (If you don't use stereo output, this will

not produce the intended eect.)

WAV (WAVEFORM)

Selects the type of wave.

TON (TONE)

Adjusts the tonal character.

ROTARY (ROT)

SLW (SLOW SPEED)

Adjusts the SLW (slow) rotation

speed.

FST (FAST SPEED)

Adjusts the FST (fast) rotation

speed.

R/H (ROTOR / HORN BALANCE)

Adjusts the balance between the

horn and the rotor.

AUTO WAH (AWH)

RES (RESONANCE)

Adjusts the depth of the wah

eect in the region of the center

frequency.

FRQ (FREQUENCY)

Species the center frequency of

the wah eect.

TYP (FILTER TYPE)

LPF:Low-pass lter. Only the low-

frequency region is passed.

HPF:High-pass lter. Only the

high-frequency region is passed.

BPF:Band-pass lter. Only a

specic frequency region is passed.

SLICER (SLI)

PTN (PATTERN)

Selects the pattern at which the

sound is sliced.

ATK (ATTACK)

Adjusts the attack volume of the

slice pattern.

DTY (DUTY)

Adjusts the length of sound for the

slice pattern.

OVERTONE (OVT)

LWR (LOWER LEVEL)

Adjusts the overtone one octave

below.

UNI (UNISON LEVEL)

Adjusts the volume at which sound

that is slightly pitch-shifted is added

to the direct sound.

UPR (UPPER LEVEL)

Adjusts the overtone one octave

above.

Panel Descriptions

7 [TAP DIVISION] button

Species the rate as a note value relative to the BPM.

Preventing accidental operation (panel lock)

By long-pressing the [TAP DIVISION] button, you can

switch between enabling (unlocking) or disabling

(locking) operation of the knobs and buttons.

If you attempt an operation while the unit is locked, the

display indicates “LCK.”

8 TAP DIVISION indicator

Indicates the rate as a note value, relative to quarter-

notes (100%) of the interval at which you press the

pedal.

TAP DIVISION indicator

Explanation

ª ˇ ¸ ˙ TRI

(

Whole note (25%)

( (

Whole-note triplet (38%)

(

Half note (50%)

( (

Half-note triplet (75%)

(

Quarter note (100%)

( (

Quarter-note triplet (150%)

TAP DIVISION indicator

Explanation

ª ˇ ¸ ˙ TRI

(

Eighth note (200%)

( (

Eighth-note triplet (300%)

9 [MEMORY] button

Switches or saves memories (MANUAL, 1–4) (p. 10).

10 MEMORY indicator

Indicates the currently selected memory.

11 [ON/OFF] switch

Turns the eect on/o.

Panel Descriptions

12 [MEMORY/TAP] switch

Switches memories (p. 10).

Long-press the [MEMORY/TAP] switch to select tap

mode.

By pressing the switch in time with the tempo of the

song you're performing, you can specify a speed of

modulation that matches the song.

When the mode is ROTARY, this switches the rotation

speed of the speaker.

MEMO

The function of the footswitch can be changed by

“MFC” (MEMORY FUNCTION).

Panel Descriptions

Rear Panel (Connecting Your Equipment)

* To prevent malfunction and equipment failure, always turn down the

volume, and turn o all the units before making any connections.

A B C D

A INPUT (A/MONO, B) jacks

Connect your guitar, bass, or eect unit here.

Use the A/MONO and B jacks if connecting an eect

unit that has stereo output. Use only the A/MONO jack

if using this unit in mono.

Turning On/O the Power

The INPUT A/MONO jack also operates as the power

switch. The power turns on when you insert a plug into

the INPUT A/MONO jack.

When powering up

Power-up equipment such as your guitar amp last.

When powering down

Power-down equipment such as your guitar amp rst.

* Before turning the unit on/o, always be sure to turn the volume

down. Even with the volume turned down, you might hear some

sound when switching the unit on/o. However, this is normal

and does not indicate a malfunction.

B OUTPUT (A/MONO, B) jacks

Connect this jack to your amp or monitor speakers.

Use only the OUTPUT A/MONO jack if using this unit in

mono. Even sound that is input in stereo is output in

mono.

The input/output jacks can be used to utilize the insert

loop function (p. 13).

C CTL 1, 2/EXP jack

Using the jack as CTL 1, 2

You can connect a footswitch (sold separately: FS-5U,

FS-6, FS-7) and use it to tap-input the rate or switch

memories (p. 11).

Panel Descriptions

Using the jack as EXP

You can connect an expression pedal (sold separately:

EV-30, Roland EV-5, etc.) and use it to control the rate or

the volume of the eect sound (p. 13).

* Use only the specied expression pedal. By connecting any other

expression pedals, you risk causing malfunction and/or damage

to the unit.

D DC IN jack

An AC adaptor (sold separately: PSA-S series) can be

connected to this jack.

* Use only the specied AC adaptor (sold separately: PSA-S series)

and plug it into an AC outlet of the correct voltage.

* If the AC adaptor is connected while power is on, the power

supply is drawn from the AC adaptor.

Side Panel (Connecting Your Equipment)

E F

E MIDI jacks

Use a TRS/MIDI connecting cable (sold separately:

BMIDI-5-35) to connect an external MIDI device. You can

use an external MIDI device to switch the memories of

this unit.

* Do not connect an audio device here. Doing so will cause

malfunctions.

F USB port (for program updates only)

Connect your computer using a commercially available

USB cable that supports USB 2.0.

* Do not use a micro USB cable that is designed only for charging a

device. Charge-only cables cannot transmit data.

* This is used only for program updates.

Saving to Memory

Here’s how to save eect settings that you edited.

1. Long-press the [MEMORY] button.

The display indicates “Wrt.”

2. Press the [MEMORY] button to select the save-

destination (MAN, 1–4).

If you decide to cancel, press the [TAP DIVISION]

button.

3. Long-press the [MEMORY] button to conrm

the save-destination.

The memory is saved.

* If you save to MAN, the settings of the panel are applied as the

values for MODE, DEPTH, E.LEVEL, and PARAM 1–3.

Switching Memories

Here’s how to recall a saved memory.

1. Press the [MEMORY] button to select a

memory.

Each time you press the button, you cycle through

the memories in the order of “MAN (manual) 01

02 03 04 0MAN...”

What is “MAN” (manual)?

This unit normally applies the eect according to the

settings that are saved in memory, but if you select MAN

(manual) the eect is applied according to the positions

of the panel knobs. Even in this case, the rate and TAP

DIVISION recall the settings that are written to MAN (this

can be changed).

Saving and Switching Memories

Tabla de contenidos

Otros manuales de Pedal de música de BOSSCO

BOSSCO

BOSSCO BCB-60 Manual de usuario

BOSSCO

BOSSCO TU-2 Chromatic Tuner Manual de usuario

BOSSCO

BOSSCO AW-3 Dynamic Wah Manual de usuario

BOSSCO

BOSSCO Chorus CE-3 Manual de usuario

BOSSCO

BOSSCO Heavy Metal HM-2 Manual de usuario

BOSSCO

BOSSCO Acoustic Simulator AC-2 Manual de usuario

BOSSCO

BOSSCO BF-2 Flanger Manual de usuario

BOSSCO

BOSSCO Metal Zone MT-2 Manual de usuario

BOSSCO

BOSSCO RE-20 COSM Manual de operación y mantenimiento

BOSSCO

BOSSCO BCB-60 Manual de usuario

BOSSCO

BOSSCO FDR-1 Manual de usuario

BOSSCO

BOSSCO OC-3 Super Octave Manual de usuario

BOSSCO

BOSSCO ME-70 Guía de configuración

BOSSCO

BOSSCO Multi Overtone MO-2 Manual de usuario

BOSSCO

BOSSCO CE-5 Manual de usuario

BOSSCO

BOSSCO OC-2 Octaver Manual de usuario

BOSSCO

BOSSCO Acoustic Simulator AC-2 Manual de usuario

BOSSCO

BOSSCO GT-1000CORE Manual de usuario

BOSSCO

BOSSCO VE-2 Manual de usuario

BOSSCO

BOSSCO ME-20 Manual de usuario

BOSSCO

BOSSCO SD-1 Manual de usuario

BOSSCO

BOSSCO CEB-3 Bass Chorus Manual de usuario

BOSSCO

BOSSCO FZ-2 Hyper fuzz Manual de usuario

BOSSCO

BOSSCO Metal Core ML-2 Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario