Bosch WZ16 Manual de usuario

WZ16 Integrated IR Bullet

Camera

WZ16

en Installation Manual

WZ16 Integrated IR Bullet Camera Table of Contents | en 3

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2011.02

Table of Contents

1Safety 4

1.1 Safety Precautions 4

1.2 Important Safety Instructions 4

1.3 Important Notices 6

1.4 FCC & ICES compliance 9

1.5 CSA certification 12

1.6 Warranty / Limitation of Liability 12

2 Introduction 14

2.1 Parts Included 14

3 Installation and Connection 15

4 Configuration 18

4.1 Adjusting the Zoom 18

4.2 Adjusting the Focus 19

4.3 Adjusting the Video Output Brightness 19

5 Troubleshooting 20

5.1 Troubleshooting Tips 20

6 Technical Specifications 21

4en | Safety WZ16 Integrated IR Bullet Camera

| 1.0 | 2011.02 Installation Manual Bosch Security Systems, Inc.

1Safety

1.1 Safety Precautions

1.2 Important Safety Instructions

Read, follow, and retain all of the following safety instructions.

Heed all warnings on the unit and in the operating instructions

before operating the unit.

1. Read these instructions.

2. Keep this instruction.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a clean, soft, dry or moistened cloth and

mild detergent solution.

7. Do not block any ventilation openings. Install in

accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat

registers, stoves or other apparatus (including amplifiers)

that produce heat.

DANGER!

High risk: This symbol indicates an imminently hazardous

situation such as “Dangerous Voltage” inside the product.

If not avoided, this will result in an electrical shock, serious

bodily injury, or death.

WARNING!

Medium risk: Indicates a potentially hazardous situation.

If not avoided, this could result in minor or moderate bodily

injury.

CAUTION!

Low risk: Indicates a potentially hazardous situation.

If not avoided, this could result in property damage or risk of

damage to the unit.

WZ16 Integrated IR Bullet Camera Safety | en 5

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2011.02

9. Do not put objects inside the camera. Make sure that no

metal objects or flammable substances enter the camera.

This may cause fire, short-circuits and other damages.

10. Be careful when handling the camera. To prevent damage,

do not drop the camera or subject it to strong shock or

vibration.

11. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong is provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

12. Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

power where they exit from the apparatus.

13. Protect the camera from humidity and dust.

14. Unplug this apparatus during lightning storms or when

unused for long periods of time.

15. Use only attachments/accessories specified by the

manufacturer.

16. Use only with the bracket sold with the apparatus.

17. Do not attempt to open or disassemble the camera to gain

access to the internal components. Refer all servicing to

qualified service personnel. Servicing is required when the

apparatus has been damaged in a way, such as power-

supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, does not operate

normally, or has dropped. When servicing, power shall be

disconnected.

18. These servicing instructions are for use by qualified service

personnel only. To reduce the risk of electric shock, do not

perform any servicing other than that contained in the

operating instructions, unless you are qualified to do so.

6en | Safety WZ16 Integrated IR Bullet Camera

| 1.0 | 2011.02 Installation Manual Bosch Security Systems, Inc.

1.3 Important Notices

All-pole power switch - Incorporate an all-pole power switch,

with a contact separation of at least 3 mm in each pole, into the

electrical installation of the building. If it is needed to open the

housing for servicing and/or other activities, use this all-pole

switch as the main disconnect device for switching off the

voltage to the unit.

Camera grounding - For mounting the camera in potentially

damp environments, ensure to ground the system using the

ground connection of the power supply connector (see section:

Connecting external power supply).

Camera lens - An assembled camera lens in the outdoor

housing must comply and be tested in accordance with UL/

IEC60065. Any output or signal lines from the camera must be

SELV or Limited Power Source. For safety reasons the

environmental specification of the camera lens assembly must

be within the environmental specification of -10 °C to 50 °C

(14°Fto122°F).

Camera signal - Protect the cable with a primary protector if

the camera signal is beyond 140 feet, in accordance with

NEC800 (CEC Section 60).

Accessories - Do not place this unit on an unstable stand,

tripod, bracket, or mount. The unit may fall, causing serious

injury and/or serious damage to the unit. Use only with the

cart, stand, tripod, bracket, or table specified by the

manufacturer. When a cart is used, use caution and care when

moving the cart/apparatus combination to avoid injury from

tip-over. Quick stops, excessive force, or uneven surfaces may

cause the cart/unit combination to overturn. Mount the unit

per the manufacturer's instructions.

WZ16 Integrated IR Bullet Camera Safety | en 7

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2011.02

Coax grounding:

– Ground the cable system if connecting an outside cable

system to the unit.

– Connect outdoor equipment to the unit's inputs only after

this unit has had its grounding plug connected to a

grounded outlet or its ground terminal is properly

connected to a ground source.

– Disconnect the unit's input connectors from outdoor

equipment before disconnecting the grounding plug or

grounding terminal.

– Follow proper safety precautions such as grounding for

any outdoor device connected to this unit.

U.S.A. models only - Section 810 of the National Electrical Code,

ANSI/NFPA No.70, provides information regarding proper

grounding of the mount and supporting structure, grounding of

the coax to a discharge unit, size of grounding conductors,

location of discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

Electronic Surveillance - This device is intended for use in

public areas only. U.S. federal law strictly prohibits

surreptitious recording of oral communications.

Environmental statement - Bosch has a strong commitment

towards the environment. This unit has been designed to

respect the environment as much as possible.

Disposal - Your Bosch product was developed and

manufactured with high-quality material and components that

can be recycled and reused. This symbol means that electronic

and electrical appliances, which have reached the end of their

working life, must be collected and disposed of separately

from household waste material. Separate collecting systems

are usually in place for disused electronic and electrical

products. Please dispose of these units at an environmentally

compatible recycling facility, per European Directive 2002/96/

EC.

8en | Safety WZ16 Integrated IR Bullet Camera

| 1.0 | 2011.02 Installation Manual Bosch Security Systems, Inc.

Electrostatic-sensitive device - Use proper CMOS/MOS-FET

handling precautions to avoid electrostatic discharge.

NOTE: Wear required grounded wrist straps and observe proper

ESD safety precautions when handling the electrostatic-

sensitive printed circuit boards.

Moving - Disconnect the power before moving the unit. Move

the unit with care. Excessive force or shock may damage the

unit and the hard disk drives.

Outdoor signals - The installation for outdoor signals, especially

regarding clearance from power and lightning conductors and

transient protection, must be in accordance with NEC725 and

NEC800 (CEC Rule 16-224 and CEC Section 60).

Permanently connected equipment - Incorporate a readily

accessible disconnect device external to the equipment.

Pluggable equipment - Install the socket outlet near the

equipment so it is easily accessible.

Power resupply - If the unit is forced to power down due to

exceeding the specified operating temperatures, disconnect

the power cord, wait for at least 30 seconds, and then

reconnect the power cord.

Power lines - Do not locate the camera near overhead power

lines, power circuits, or electrical lights, nor where it may

contact such power lines, circuits, or lights.

SELV - All the input/output ports are Safety Extra Low Voltage

(SELV) circuits. SELV circuits should only be connected to

other SELV circuits.

Because the ISDN circuits are treated like telephone-network

voltage, avoid connecting the SELV circuit to the Telephone

Network Voltage (TNV) circuits.

System ground/Safety ground

System (video) ground is indicated by the symbol .

Safety (power) ground is indicated by the symbol .

The system ground is only used to comply with safety standards

or installation practices in certain countries. Bosch does not

recommend connecting system ground to safety ground unless

it is explicitly required. However, if the system ground and

WZ16 Integrated IR Bullet Camera Safety | en 9

Bosch Security Systems, Inc. Installation Manual | 1.0 | 2011.02

safety ground are connected and grounding loops are causing

interference in the video signal, use an isolation transformer

(available separately from Bosch).

Video loss - Video loss is inherent to digital video recording;

therefore, Bosch Security Systems cannot be held liable for any

damage that results from missing video information. To

minimize the risk of lost digital information, Bosch Security

Systems recommends multiple, redundant recording systems,

and a procedure to back up all analog and digital information.

1.4 FCC & ICES compliance

FCC Information

(U.S.A. and Canadian Models Only)

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following

measures:

– Fit Ferrite beads on all cable to and from the power supply

box, within the box walls.

– Route the composite cable between the camera and the

power supply in steel conduit piping over the entire run of

the cable up to and including connection to a deep conduit

CAUTION!

Connecting System ground to Safety ground may result in

ground loops that can disrupt the CCTV system.

10 en | Safety WZ16 Integrated IR Bullet Camera

| 1.0 | 2011.02 Installation Manual Bosch Security Systems, Inc.

base fitted under the camera and a conduit fitting adaptor

in the wall of the PSU box.

– Reorient or relocate the receiving antenna;

– Increase the separation between the equipment and

receiver;

– Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected;

– Consult your Bosch Service Center, dealer, or an

experienced radio/TV technician for further advice.

Intentional or unintentional modifications, not expressly

approved by the party responsible for compliance, shall not be

made. Any such modifications could void the user's authority to

operate the equipment. If necessary, the user should consult

the dealer or an experienced radio/television technician for

corrective action.

The user may find the following booklet, prepared by the

Federal Communications Commission, helpful: How to Identify

and Resolve Radio-TV Interference Problems. This booklet is

available from the U.S. Government Printing Office,

Washington, DC 20402, Stock No. 004-000-00345-4.

Informations FCC et ICES

(modèles utilisés aux États-Unis et au Canada uniquement)

Suite à différents tests, cet appareil s'est révélé conforme aux

exigences imposées aux appareils numériques de classe B, en

vertu de la section 15 du règlement de la Commission fédérale

des communications des États-Unis (FCC), et en vertu de la

norme ICES-003 d'Industrie Canada. Ces exigences visent à

fournir une protection raisonnable contre les interférences

nuisibles lorsque l'appareil est utilisé dans le cadre d'une

installation résidentielle. Cet appareil génère, utilise et émet

de l'énergie de radiofréquences et peut, en cas d'installation ou

d'utilisation non conforme aux instructions, engendrer des

interférences nuisibles au niveau des radiocommunications.

Toutefois, rien ne garantit l'absence d'interférences dans une

installation particulière. Il est possible de déterminer la

production d'interférences en mettant l'appareil

Otros manuales para WZ16

Tabla de contenidos

Otros manuales de Cámara de seguridad de Bosch

Bosch

Bosch MIC440AXWUD14636N Manual de usuario

Bosch

Bosch AUTODOME IP 5000 HD NEZ-5 Series Manual de usuario

Bosch

Bosch VCM8637/00T Manual de usuario

Bosch

Bosch FlexiDome NDC-455V03-21PS Manual de usuario

Bosch

Bosch VDC-250 Manual de usuario

Bosch

Bosch MIC Series 400 Manual de usuario

Bosch

Bosch EX40 Manual de usuario

Bosch

Bosch AUTODOME IP 5000i IR Manual de usuario

Bosch

Bosch KBE-335V55-20 Manual de usuario

Bosch

Bosch EXTEGRA IP 9000 FX Manual de usuario

Bosch

Bosch AUTODOME IP 4000i Manual de usuario

Bosch

Bosch AUTODOME IP starlight 5000i IR Manual de usuario

Bosch

Bosch NPD-5512-Z30 Manual de usuario

Bosch

Bosch DINION IP 5000 HD Manual del propietario

Bosch

Bosch DINION 5000 IP Manual de usuario

Bosch

Bosch LTC-0498-28W Manual de usuario

Bosch

Bosch DINION IP 7000 HD NBN-71022 Manual de usuario

Bosch

Bosch FLEXIDOME NIN-733 Manual de usuario

Bosch

Bosch LTC 0440 Series Manual de usuario

Bosch

Bosch AutoDome 100 Series Manual de usuario

Bosch

Bosch DINION IP starlight 7000 HD Manual de usuario

Bosch

Bosch VDN-498V06-21S Manual de usuario

Bosch

Bosch DINION IP starlight 7000 HD Manual de usuario

Bosch

Bosch VJR-A3-IC Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario