Bosch LR8 Instrucciones de montaje

Operating / Safety Instructions

Consignes d’utilisation / de sécurité

Instrucciones de funcionamiento y seguridad

LR8

IMPORTANT:

Read Before Using

IMPORTANT :

Lire avant usage

IMPORTANTE:

Leer antes de usar

English Version

See page 5

LR8

Professional

Call Toll Free for Consumer Information & Service Locations

Pour obtenir des informations et les adresses de nos centres de

service après-vente, appelez ce numéro gratuit

Llame gratis para obtener información para el consumidor y

ubicaciones de servicio

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-2-

LR8

Professional

Batt. 2x1.5V LR6 (AA)

Robert Bosch Tool Corp.

Mount Prospect,IL

LR8

1 618 C01 18C

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-3-

LR8

Professional

LR7

Professional

LR8

Professio

nal

LR7

Professional

LR8

Professio

nal

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-4-

General Safety Rules

Read all instructions. Failure to follow all

instructions listed below may result in electric

shock, ﬁre and/or serious injury.

SAVE THESE INSTRUCTIONS

Work area safety

Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

DO NOT operate the laser tool around children or allow chil-

dren to operate the laser tool. Serious eye injury could result.

Electrical safety

Batteries can explode or leak, cause injury or

ﬁre. To reduce this risk, always follow all

instructions and warnings on the battery label and package.

Safety Symbols

The definitions below describe the level of severity for each signal

word. Please read the manual and pay attention to these symbols.

This is the safety alert symbol. It is used to

alert you to potential personal injury hazards.

Obey all safety messages that follow this

symbol to avoid possible injury or death.

Read manual symbol - Alerts user to read

manual.

WARNING indicates a hazardous situation

which, if not avoided, could result in death or

serious injury.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-5-

DO NOT short any battery terminals.

DO NOT charge alkaline batteries.

DO NOT mix old and new batteries. Replace all of them at the

same time with new batteries of the same brand and type.

DO NOT mix battery chemistries. Dispose of or recycle batter-

ies per local code.

DO NOT dispose of batteries in ﬁre.

Keep batteries out of reach of children.

Remove batteries if the device will not be used for several

months.

FCC Statement

Changes or modiﬁcations to this unit not

expressly approved by the party responsible for

compliance could void the user’s authority to operate the

equipment.

Note: This product has been tested and found to comply with the

limits for a Class B Digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communica-

tions. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment oﬀ and on, the user is

encouraged to try to correct the interference by one or more of

the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit diﬀerent from

that to which the receiver is connected.

– Consult the dealer or an experienced radio TV technician for

help.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-6-

Personal safety

Stay alert, watch what you are doing and use

common sense when operating a tool. Do not

use a tool while you are tired or under the inﬂuence of drugs,

alcohol or medication. A moment of inattention while operating a

tool may result in serious personal injury or incorrect measure-

ment results.

Use safety equipment. Always wear eye protection. Safety

equipment such as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

Keep the measuring tool away from cardiac pace-

makers. The magnet plate 7generates a ﬁeld that

can impair the function of cardiac pacemakers.

Keep the measuring tool away from magnetic data medium and

magnetically-sensitive equipment. The eﬀect of the magnet plate

7can lead to irreversible data loss.

Noise Information

The A-weighted sound pressure level of the audio signal at one

meter distance is 80 dB(A).

Do not hold the tool close to your ear!

Use and care

Use the correct tool for your application. The

correct tool will do the job better and safer.

Do not use the tool if the switch does not turn it on and oﬀ. Any

tool that cannot be controlled with the switch is dangerous and

must be repaired.

Store idle tool out of the reach of children and do not allow

persons unfamiliar with the tool or these instructions to oper-

ate the tool. Tools are dangerous in the hands of untrained users.

Maintain tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may af-

fect the operation. If damaged, tool repaired before use. Many

accidents are caused by poorly maintained tools.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-7-

Intended Use

The tool is intended for detecting pulsating line lasers.

Preparation

Inserting/Replacing the Battery

Alkaline batteries are recommended for the tool.

Pull the latch 16 of battery lid outward and open the battery lid 15.

When inserting batteries, pay attention to the correct polarity.

When the battery low indicator aappears for the ﬁrst time on the

display 6, the measuring tool can still be operated for approx. 2 h.

Remove the batteries from the tool when not

using it for extended periods. When storing

for extended periods, the batteries can corrode and discharge

themselves.

Use the tool, accessories, etc., in accordance with these in-

structions and in the manner intended for the particular type of

tool, taking into account the working conditions and the work

to be performed. Use of the tool for operations diﬀerent from

those intended could result in a hazardous situation.

Service

Have your tool serviced by a qualiﬁed repair person using only

identical replacement parts. This will ensure that the safety of

the tool is maintained.

Develop a periodic maintenance schedule for tool. When clean-

ing a tool be careful not to disassemble any portion of the tool

since internal wires may be misplaced or pinched or may be

improperly mounted. Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may damage plastic parts.

SAVE THESE INSTRUCTIONS.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-8-

Display Elements

aBattery level indicator

bDirection indicator “move downward”

cCenter indicator

dDirection indicator “move upward”

eIndicator for measuring accuracy “Coarse”

fIndicator for measuring accuracy “Fine”

gAudio signal indicator

Features

The numbering of the product features shown refers to the illustra-

tion of the tool on the graphic page.

1 Speaker

2Accuracy button

3On/Oﬀ button

4Audio signal button

5Reception area for the

laser beam

6Display

7Magnets

8Guide groove for holder

9Center-indication LED (rear)

10 Direction LED “move

downward”

11 Center mark

12 Direction LED “move

upward”

13 Type plate

14 Serial number

15 Battery lid

16 Latch of battery lid

17 Mounting bracket

18 Rotary knob of the

mounting bracket

19 Guide rail

20 Mounting bracket latch

21 Push-button to release

the lock

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-9-

Laser Receiver ................................................LR8

Article number .......................................3601 K69 J11

Working range1) .................................... 15’-165’ (5-50 m)

Receiving angle ................................................ 90°

Measuring accuracy2)

– “Fine” adjustment ..................................±1/32” (±1 mm)

– “Coarse” adjustment .................................±1/8” (±3 mm)

Operating temperature ................14°F....+122 °F (–10 °C...+50 °C)

Storage temperature .................. -4°F...+158 °F (–20 °C...+70 °C)

Max. altitude...................................................6560 ft (2000 m)

Relative air humidity, max....................................................90%

Pollution degree according IEC 610103) ..........................................3

Batteries ..........................................2x1.5V LR6 (AA)

Operating time, approx. .........................................30h

Weight .......................................... .0.33 lb (0.150 kg)

Degree of protection ...............IP54(dust and splash water protected)

Dimensions (length x width x height) . . . 2.9” x 1.1” x 5.4” (73 x 28 x 137 mm)

1) The working range can be decreased by unfavorable environmental

conditions (e.g. direct sun exposure).

2) The angular accuracy between the 45° laser line and the 90° laser line is

max. ±5/32 @ 30 ft (+/-0.4 mm/m).

3) Conductive pollution occurs, or dry, non-conductive pollution occurs

which becomes conductive due to condensation which is expected. In such

conditions, equipment is normally protected against exposure to direct

sunlight, precipitation, and full wind pressure, but neither temperature nor

humidity is controlled.

Please observe the article number on the type plate of your tool.

The trade names of the individual tools may vary.

The tool can be clearly identified with the serial number 14 on the type plate.

Technical Data

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

-10-

Operation

Initial Operation

tProtect the tool against moisture.

tDo not subject the tool to extreme temperatures or variations

in temperature. As an example, do not leave it in vehicles for

longer periods. In case of large variations in temperature, allow

the tool to adjust to the ambient temperature before putting it

into operation. In case of extreme temperatures or variations in

temperature, the accuracy of the tool can be impaired.

DO NOT stare directly at the laser beam or project

the laser beam directly into the eyes of others.

Serious eye injury could result.

Setting Up the Tool (see ﬁgure A)

Position the tool at least 17 ft (5 m) away from the cross-line

laser. Switch on the pulsating function of the cross-line laser and

select horizontal or vertical operation.

Note: Do not select cross-line operation or else faulty indications

on the height of the laser beam can occur.

Position the tool in such a manner that the laser beam can reach

the reception area 5. Align the tool in such a manner that the la-

ser beam runs horizontally through the reception area (as shown

in the ﬁgure).

Switching On and Oﬀ

tA loud audio signal sounds when switching on the tool. There-

fore, keep the tool away from your ear or other people when

switching on. The loud audio signal can cause hearing defects.

To switch on the tool, press the On/Oﬀ button 3. An audio signal

will sound and all LEDs will light up brieﬂy.

To switch oﬀ the tool, press the On/Oﬀ button 3again. All dis-

play indicators as well as all LEDs light up brieﬂy and an audio

signal sounds before the tool switches oﬀ.

www.GlobalTestSupply.com

Find Quality Products Online at: sales@GlobalTestSupply.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Nivel láser de Bosch

Bosch

Bosch GLL 2-50 Professional Manual de usuario

Bosch

Bosch GLL 30 Instrucciones de montaje

Bosch

Bosch GPL 5 Professional Manual de usuario

Bosch

Bosch PLL 1 P Manual de usuario

Bosch

Bosch GRL900-20HV Instrucciones de montaje

Bosch

Bosch GLL 2-20 Professional Manual de usuario

Bosch

Bosch Professional GLL 50 G Manual de usuario

Bosch

Bosch GCL 2-15 Manual de usuario

Bosch

Bosch DNM 120 L Manual de usuario

Bosch

Bosch EasySpiritLevel Manual de usuario

Bosch

Bosch 3 603 K63 V10 Instrucciones de montaje

Bosch

Bosch GLL Professional 3-80 C Manual de usuario

Bosch

Bosch Quigo Plus Manual de usuario

Bosch

Bosch GLL 3-80 CG Manual de usuario

Bosch

Bosch GCL 25 Professional Manual de usuario

Bosch

Bosch PAM 220 Manual de usuario

Bosch

Bosch GAM220MF Professional Manual de usuario

Bosch

Bosch Quigo Manual de usuario

Bosch

Bosch GRL Professional 250 HV Manual de usuario

Bosch

Bosch GPL 5 Professional Manual de usuario

Bosch

Bosch GTL 3 Professional Manual de usuario

Bosch

Bosch Quigo Manual de usuario

Bosch

Bosch GPL3T Instrucciones de montaje

Bosch

Bosch BL 100 VHR Manual de usuario

Manuales populares de Nivel láser de otras marcas

Nedo

Nedo ET-5 Manual de usuario

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Manual de usuario

LaserLiner

LaserLiner X2-Laser Manual de usuario

Spectra

Spectra LL300N Manual de usuario

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Manual de usuario

Nedo

Nedo Crossliner 4 Manual de usuario

Lasertec

Lasertec FX360G Manual de usuario

Flex

Flex ALC 8 Manual de usuario

Black & Decker

Black & Decker LZR5 Manual de usuario

Johnson

Johnson 40-6692 Manual de usuario

Cocraft

Cocraft HL 20-SG Manual de usuario

Zircon

Zircon iLine Manual de usuario

HWH

HWH 310 SERIES Manual de usuario

Leica

Leica iCON robot 60 Manual de usuario

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Manual de usuario

LaserLiner

LaserLiner ActiveFinder XP Manual de usuario

DeWalt

DeWalt DW082 Manual de usuario

imex

imex EL20 Manual de usuario