Bosch NWC-0495-20P Manual de usuario

Dinion IP

NWC-495-10P | NWC-495-20P

en Operating Instructions

Dinion IP | en 3

Bosch Security Systems Operating Instructions V 2.5 | 2007.6

Table of Contents

1 Introduction 15

1.1 Type number overview 16

1.2 Unpacking 16

1.3 System requirements 17

1.4 Overview of functions 17

1.4.1 Wide dynamic range 18

1.4.2 Day/Night function 18

1.4.3 Power-over-Ethernet 18

1.4.4 Receiver 18

1.4.5 Video encoding 18

1.4.6 Tri Streaming 19

1.4.7 Recording 19

1.4.8 Multicast 19

1.4.9 Encryption 19

1.4.10 Configuration 19

1.4.11 Tampering recognition and motion detectors 19

1.4.12 Snapshots 20

1.4.13 Backup 20

1.4.14 Intelligent Video Motion Detection 20

2 Connections 21

2.1 Power 21

2.2 Network (and power) 22

2.3 Video service monitor 22

2.4 Alarm connector 23

3Mounting 24

3.1 Lens mounting 24

3.2 Mounting the camera 25

4 Quick set-up 26

4.1 Back focus adjustment 26

4.2 Accessing and navigating quick set-up menu 27

4en | Dinion IP

docnumber | V 2.5 | 2007.6 Operating Instructions Bosch Security Systems

4.2.1 How to use the navigation keys 27

4.2.2 Install menu 28

4.3 Adjustment procedure DC-iris Lens 28

4.4 Adjustment procedure Manual-iris Lens 29

4.5 Adjustment procedure Video-iris Lens 29

4.6 Install IP address submenu 29

4.7 Defaults 30

5 Network connection 31

5.1 System requirements 31

5.2 Establishing the connection 31

5.3 Secured network 33

6 Operation via the browser 34

6.1 Livepage 34

6.1.1 Processor load 34

6.1.2 Image selection 35

6.1.3 Digital I/O 35

6.1.4 System log / Event log 35

6.1.5 Saving snapshots 35

6.1.6 Recording video sequences 36

6.1.7 Running recording program 37

6.2 Recordings page 37

6.2.1 Selecting recordings 38

6.2.2 Controlling playback 38

7 Configuration via the browser 41

7.1 Settings 41

7.2 General Settings 43

7.2.1 Camera identification 43

7.2.2 Password protection 44

7.2.3 Language selection 45

7.2.4 Date and time 45

7.2.5 Time server 46

7.3 Display Settings 47

7.3.1 Display stamping 47

Dinion IP | en 5

Bosch Security Systems Operating Instructions V 2.5 | 2007.6

7.4 Encoder Settings 48

7.4.1 Selecting an encoder profile 48

7.4.2 Changing profiles 50

7.4.3 JPEG posting 53

7.5 Camera settings 55

7.5.1 ALC 55

7.5.2 Shutter/AGC 56

7.5.3 Day/Night 57

7.5.4 Enhance 58

7.5.5 Color 59

7.5.6 Back Light Compensation (BLC) 60

7.5.7 Installer options 61

7.6 Recording 61

7.6.1 Type 62

7.6.2 Storage information 62

7.7 iSCSI settings 63

7.7.1 iSCSI IP address 63

7.7.2 iSCSI LUN map 64

7.7.3 Target IP address 64

7.7.4 Target node 64

7.7.5 Target LUN 64

7.7.6 Target password 64

7.7.7 Initiator name 65

7.7.8 Initiator extension 65

7.7.9 Decoupling the drive used 65

7.7.10 Storage information 65

7.8 Partitioning 66

7.8.1 Creating a partition 66

7.8.2 Partition status 68

7.8.3 Editing a partition 68

7.8.4 Deleting partitions 71

7.9 Recording profile 71

7.10 Recording scheduler 74

7.10.1 Activating recording 75

7.10.2 Recording status 76

7.11 Alarm Settings 76

7.11.1 Alarm in 76

6en | Dinion IP

docnumber | V 2.5 | 2007.6 Operating Instructions Bosch Security Systems

7.11.2 Alarm connections 77

7.12 VCA 79

7.12.1 Analysis 79

7.12.2 Analysis type 80

7.12.3 Motion detector 80

7.12.4 Sensitivity 81

7.12.5 Tamper detection 82

7.13 Alarm e-mail 84

7.13.1 Send alarm e-mail 84

7.13.2 Mail server IP address 84

7.13.3 Layout 85

7.13.4 Destination address 85

7.13.5 Sender name 85

7.13.6 Send e-mail for testing 85

7.14 Relay Settings 85

7.14.1 Alarm out 86

7.15 Service Settings 87

7.15.1 Network 87

7.15.2 Multicasting 90

7.15.3 Encryption 92

7.15.4 Version information 93

7.15.5 Livepage configuration 94

7.15.6 Licenses 96

7.15.7 Maintenance 97

7.16 Function test 99

8 Connections between video servers 100

8.0.1 Installation 100

8.0.2 Establishing the connection 100

8.0.3 Connect on alarm 100

8.0.4 Connecting with a Web browser 101

8.0.5 Closing the connection 101

Dinion IP | en 7

Bosch Security Systems Operating Instructions V 2.5 | 2007.6

9 Operation with decoder software 102

10 Maintenance 103

10.1 Testing the network connection 103

10.2 Repairs 103

10.2.1 Transfer and disposal 103

11 Troubleshooting 104

12 Specifications 106

12.1 Dimensions (mm/inch) 108

12.2 Accessories 109

12.2.1 Recommended lenses 109

12.2.2 Power transformers 109

13 Glossary 110

8en | Dinion IP

docnumber | V 2.5 | 2007.6 Operating Instructions Bosch Security Systems

Important safety instructions

Read, follow, and retain all of the following safety instructions.

Heed all warnings on the unit and in the operating instructions

before operating the unit.

Type numbers: NWC-495-10P, NWC-495-20P

1. Cleaning - Unplug the unit from the outlet before cleaning.

Follow any instructions provided with the unit. Generally,

using a dry cloth for cleaning is sufficient, but a moist fluff-

free cloth or leather shammy may also be used. Do not use

liquid cleaners or aerosol cleaners.

2. Heat Sources - Do not install the unit near any heat sources

such as radiators, heaters, stoves, or other equipment

(including amplifiers) that produce heat.

3. Water - Do not use this unit near water, for example near a

bathtub, washbowl, sink, laundry basket, in a damp or wet

basement, near a swimming pool, in an unprotected out-

door installation, or in any area classified as a wet location.

To reduce the risk of fire or electrical shock, do not expose

this unit to rain or moisture.

4. Object and liquid entry - Never push objects of any kind

into this unit through openings as they may touch danger-

ous voltage points or short-out parts that could result in a

fire or electrical shock. Never spill liquid of any kind on the

unit. Do not place objects filled with liquids, such as vases

or cups, on the unit.

5. Controls adjustment - Adjust only those controls specified

in the operating instructions. Improper adjustment of

other controls may cause damage to the unit. Use of con-

trols or adjustments, or performance of procedures other

than those specified, may result in hazardous radiation

exposure.

6. Overloading - Do not overload outlets and extension cords.

This can cause fire or electrical shock.

7. Power cord and plug protection - Protect the plug and

power cord from foot traffic, being pinched by items

placed upon or against them at electrical outlets, and its

Dinion IP | en 9

Bosch Security Systems Operating Instructions V 2.5 | 2007.6

exit from the unit. For units intended to operate with

230 VAC, 50 Hz, the input and output power cord must

comply with the latest versions of IEC Publication 227 or

IEC Publication 245. For outdoor use the power cord must

comply to NEC400-4 (CEC Rule 4-010) and marked with

OUTDOOR, W, or W-A. .

8. Power sources - Operate the unit only from the type of

power source indicated on the label. Before proceeding,

be sure to disconnect the power from the cable to be

installed into the unit.

– For battery powered units, refer to the operating

instructions.

– For external power supplied units, use only the rec-

ommended or approved power supplies.

– For limited power source units, this power source

must comply with EN60950. Substitutions may dam-

age the unit or cause fire or shock.

– For 24 VAC units, voltage applied to the unit's power

input should not exceed 28 VAC. User-supplied wiring

must comply with local electrical codes (Class 2

power levels). Do not ground the supply at the termi-

nals or at the unit's power supply terminals.

– If unsure of the type of power supply to use, contact

your dealer or local power company.

9. Servicing - Do not attempt to service this unit yourself.

Opening or removing covers may expose you to dangerous

voltage or other hazards. Refer all servicing to qualified

service personnel.

10. Damage requiring service - Unplug the unit from the main

AC power source and refer servicing to qualified service

personnel when any damage to the equipment has

occurred, such as:

– the power supply cord or plug is damaged;

– exposure to moisture, water, and/or inclement

weather (rain, snow, etc.);

– liquid has been spilled in or on the equipment;

– an object has fallen into the unit;

10 en | Dinion IP

docnumber | V 2.5 | 2007.6 Operating Instructions Bosch Security Systems

– unit has been dropped or the unit cabinet is damaged;

– unit exhibits a distinct change in performance;

– unit does not operate normally when the user cor-

rectly follows the operating instructions.

11. Replacement parts - Be sure the service technician uses

replacement parts specified by the manufacturer, or that

have the same characteristics as the original parts. Unau-

thorized substitutions may cause fire, electrical shock, or

other hazards.

12. Safety check - Safety checks should be performed upon

completion of service or repairs to the unit to ensure

proper operating condition.

13. Installation - Install in accordance with the manufacturer's

instructions and in accordance with applicable local codes.

14. Attachments, changes, or modifications - Only use attach-

ments/accessories specified by the manufacturer. Any

change or modification of the equipment, not expressly

approved by Bosch, could void the warrantee or, in the

case of an authorization agreement, authority to operate

the equipment.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara IP de Bosch

Bosch

Bosch DinionHD NBN-921 Manual de usuario

Bosch

Bosch MicroDome NDC-274-PT Instrucciones de uso

Bosch

Bosch NDN-921 Guía de instalación

Bosch

Bosch FLEXIDOME IP NIN-70122 Manual de usuario

Bosch

Bosch NBC-455 Manual de usuario

Bosch

Bosch NDP-5512-Z30 Manual de usuario

Bosch

Bosch NBC-255-P Manual de usuario

Bosch

Bosch NWC-0455-20P Manual de usuario

Bosch

Bosch AVIOTEC IPSTARLIGHT 8000 Manual de usuario

Bosch

Bosch AUTODOME 7100i Manual de usuario

Bosch

Bosch NBC-255-P Instrucciones de uso

Bosch

Bosch Autodome IP 4000 HD Instrucciones de montaje

Bosch

Bosch NBC-455 Manual de usuario

Bosch

Bosch NDC-225-PI Instrucciones de uso

Bosch

Bosch NEC-070V09-21W Manual de usuario

Bosch

Bosch AN traffic 4000 IR Manual de usuario

Bosch

Bosch Infrared Imager EX80 Manual de usuario

Bosch

Bosch LTC 9450 Series Unity Dome Manual de usuario

Bosch

Bosch NDC-455 Manual de usuario

Bosch

Bosch NTC-265-PI Manual de usuario

Bosch

Bosch NDN-265-PIO Manual de usuario

Bosch

Bosch NFN-70122 Manual de usuario

Bosch

Bosch NDC-265-P Manual de usuario

Bosch

Bosch NDN-50022-A3 Manual de usuario

Manuales populares de Cámara IP de otras marcas

FLIR

FLIR Exx series Manual de usuario

Avigilon

Avigilon H4A-BO1-IR Manual de usuario

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manual de usuario

ShareTech

ShareTech AV1 Manual de usuario

Ezviz

Ezviz C6C Manual de usuario

Melchioni

Melchioni UCAM 2015 Manual de usuario

Geutebruck

Geutebruck G-Cam/ESD-4630 Manual de usuario

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manual de usuario

Mitel

Mitel 6800i Series Manual de servicio

Vitek

Vitek VTC-IR403-212NP Manual de usuario

THOMSON

THOMSON DSC - 323W Manual de usuario

AVer

AVer FB2027 Manual de usuario

ENFORCER

ENFORCER EV-T5105-N2SQ Manual de usuario

Wansview

Wansview NC543 Manual de usuario

Eneo

Eneo MCB-64A0003M0A Manual de usuario

deView electronics

deView electronics CBDNI36F Manual de usuario

Swann

Swann SwannEye Manual de usuario

LevelOne

LevelOne IP CamSecure Manual de usuario