Bosch MED17.5.2 Manual de usuario

info@chiptuningshop.co.uk

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 1.

1. Description: This probe can be used for programming VAG MED17.5. Bosch ECU`s. It fits in most BDM

positioning frames and is fitted with LED`s for accurate alignment on the ECU. The “Boot” resistors and the

ignition feed can be switched. With this adapter, there is no need to solder at all.

Adapter Overview

A = Serial port connection B = Power Switch ON/OFF

C = Power Jack D = DIP Switches for BOOT Resistors ON/OFF

E = Ignition selection switch:

ON/OFF/K-Line

Since the AVDI requires a permanent connection via a 510 Ohm resistor between the K-Line and 1 V, This switch

has no function in the AVDI version of this probe.

SET TO “K-Line” POS T ON AT ALL T MES

F = Connect to flash tool. G = Connect to serial port on probe (A)

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 2.

2. Handling and Adjustment: MPORTANT - Make sure that the power switch (B) is in the “OFF” position.

The power switch must remain OFF so that the pins are not live, until the probe is correctly aligned and in

contact with the corresponding pins on the ECU. Failure to follow these instructions could result in damage

to the ECU!

Place the probe into the BDM frame retaining bracket and tighten the screws. Attach the adapter cable (G) to

the serial port (A) on the probe and plug the other end (F) into the OBD cable of your flash tool. Connect the

power supply to the probe jack (C), the LED's will now turn on to aid alignment, however the probe does not

power the ECU until the power switch (B) is turned on.

Adjust the ECU on the frame and move the retainer carefully towards the ECU. Ensure that all the pins are in

their designated position.

A diagram showing the location of the connections can be found on page 3.

t is very important, that the retainer is free from backlash and moves smoothly!

3. Reading password: (This step is only necessary for TP8+). Lift up the Boot DIP switches (D) as shown in

the adapter overview on page 1 and set the Ignition switch (E) to the “ON” position, you can now read the

password.

4. Programming the ECU: Push the DIP switches (D) down and set the “Ignition” switch (E) to the “K-Line”

position, then you can proceed with programming over boot mode.

5. Disconnecting: To safely disconnect the probe from the ECU, you must first remove TURN OFF THE

POWER Switch (B). Once the power supply is disconnected it is safe to lift the frame and probe away from

the ECU.

Manual for using MED17.5.2 Bosch ECU probe with AVD – Page 3.

The pads marked in red have to make contact with the probe.

Technical alterations reserved!

This product should be operated by competent personnel only. Chiptuningshop Ltd do not accept any responsibility

for damages, direct or consequential caused by improper handling.

Tabla de contenidos

Otros manuales de Unidad de control de Bosch

Bosch

Bosch Rexroth ctrlX I/O XI322204 Manual de usuario

Bosch

Bosch Rexroth IMdev Manual de usuario

Bosch

Bosch Rextroth Indramat RECO R-IB IL CNT Instrucciones de uso

Bosch

Bosch TouchOne Manual de usuario

Bosch

Bosch Security Systems Blue Line A1-CC Manual de usuario

Bosch

Bosch Control 8313 Manual de instrucciones

Bosch

Bosch ECU MS 25 Sport Manual de usuario

Bosch

Bosch Rexroth VT-HMC 1X Series Manual de usuario

Bosch

Bosch B426 Manual de usuario

Bosch

Bosch MS 6 Manual de usuario

Bosch

Bosch MS 3 Sport GT3 Cup Manual de usuario

Bosch

Bosch KTS Truck Manual de usuario

Bosch

Bosch CL400 Manual de usuario

Bosch

Bosch B426 Manual de usuario

Bosch

Bosch rexroth 4WS2EM10 5X XH Series Manual de usuario

Bosch

Bosch OMNEO OM-1 Manual de usuario

Bosch

Bosch Rexroth IndraControl XM21 Manual de usuario

Bosch

Bosch Rexroth IndraControl XFE 01.1 Series Manual de usuario

Bosch

Bosch Rexroth SB24/34 Manual de usuario

Bosch

Bosch GCY 30-5 T Instrucciones de montaje

Bosch

Bosch D9133TTL-E Manual de usuario

Bosch

Bosch Rexroth IndraControl S67 Series Guía del usuario

Bosch

Bosch VCU Manual de usuario

Bosch

Bosch FLM-I 420-S Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario