Bosch D7039 Manual de usuario

D7039

Installation Guide

Multiplex Expansion

Module

Bosch | 09/05 | 38685F2

D7039 | Installation Guide |

Notices

Use these instructions to install the D7039 Multiplex

Expansion Module in a fire system supervised by a

D7024 Fire Alarm Control Panel (FACP).

Install, test, and maintain the D7039 according to these

instructions, NFPA 72, local codes, and the Authority

Having Jurisdiction (AHJ).

Follow the procedures in this document to

avoid personal injury and damage to the

equipment. Failure to follow these

procedures can cause the D7039 to not

operate properly. Bosch is not responsible

for improperly installed, tested, or maintained

devices.

For the D7039 with ROM version 1.04 to

operate properly, the D7024 FACP must be

running version 2.05 or later firmware.

1.0 Description

The D7039 (Figure 1) connects directly to the FACP for

either two Class B multiplex buses or one Class A

multiplex bus that allows up to 247 remote points.

When configured for Class A operation,

the D7039 can only support Addresses 9

through 128.

Notices

21 3

4 5 6

7 8 9

Cmnd

Prog

Clear

Disable

Drill

Test

Histo ry

Reset

Silence

Trouble

Silenced

Power

Alarm

1 - D7024 Control Board

2 - Enclosure

3 - I/O module for the D7039

4 - D7039 Module

Figure 1: D7039 Module Location

3Bosch | 09/05 | 38685F

D7039 | Installation Guide | 2.0 Installation

2.0 Installation

Failure to follow the mounting instructions in this document can damage the FACP.

The D7039 and D7024 have static sensitive components and must be handled with care. Follow the

anti-static procedures when handling these modules.

Before installing the D7039 Module, remove all AC and battery power to the FACP.

1. If the D7024 is already installed in an enclosure, remove it.

2. Place the FACP on a flat surface with the component side facing up (Item 2 in Figure 2).

3. Insert the four plastic standoffs in the mounting holes (Item 3 in Figure 2) without bending or flexing the FACP.

4. Align the standoff tabs so they do not touch the module components.

5. Firmly press the standoffs into the board, allowing the ears to expand out.

6. Mount the D7039 on the standoffs, ensuring the FACP connector pins (Item 4 in Figure 2) are properly aligned.

7. Install the FACP in the enclosure.

8. Use the mounting screw (Item 5 in Figure 2) to secure the D7039’s ground wire (Item 6 in Figure 2) to the FACP.

21 3

4 5 6

7 8 9

Cmnd

Prog

Clear

Disable

Drill

Test

History

Reset

Silence

Trouble

Silenced

Power

Alarm

1 - D7039 Module 4 - FACP connector pins to align with the D7039

2 - D7024 FACP 5 - Mounting screw

3 - Standoff mounting holes (4) 6 - Ground wire

Figure 2: Mounting the D7039 on the D7024

Bosch | 09/05 | 38685F4

D7039 | Installation Guide |

9. Mount the D7039 I/O Module (Item 1 in Figure 3) in the FACP enclosure (Item 2 in Figure 3) using the mounting

holes in the enclosure (Item 3 in Figure 3).

10. Connect the yellow and green earth ground wire from the I/O module to the earth ground terminal on the

FACP control board (Item 4 in Figure 3).

3.0 Wiring

1. Connect the D7039 multiplex loop using up to 3800 ft (1170 m) of 18 AWG (1.0 mm2) or 5950 ft (1810 m) of

16 AWG (1.5 mm2) wire (Figure 4). Do not use shielded wire.

Do not use shielded wire. Twisted pair is acceptable, but is not recommended.

2.0 Installation

Figure 4: Connecting the Mux Class “A” and Class “B”

1 - I/O module for the D7039, wired Class “A” 4 - Mux B Addresses 129 through 255

2 - Class “A” Addresses 9 through 128 5 - Mux A Addresses 9 through 128

3 - I/O module for the D7039, wired Class “B”

Note: All terminals are supervised.

21 3

4 5 6

7 8 9

Cmnd

Prog

Clear

Disable

Drill

Test

History

Reset

Silence

Trouble

Silenced

Power

Alarm

1 - I/O module 3 - Holes (3) and standoffs (3) to mount the I/O module

2 - Enclosure 4 - I/O module earth ground wire to the D7024 terminal connection

Figure 3: Installing the Input-Output Module

5Bosch | 09/05 | 38685F

D7039 | Installation Guide | 4.0 Specifications

Figure 5: Measuring Class “B” Loop Resistance

1 - 50

Ω

maximum 2 - Mux bus wires 3 - Clip lead

Figure 6: Measuring Class “A” Loop Resistance

1 - 50

Ω

maximum 2 - Mux bus wires 3 - Clip lead

You can configure the D7039 with a single fault tolerant Class “A” loop or as a pair of supervised Class “B”

loops. When configured as a Class “A” loop and installed on a D7024 Control Panel before Lot #100, the

D7039 implements a Style 4.5 signaling line circuit (SLC). When installed on a D7024 Control Panel Lot #100

or later, the D7039 implements Style 6 SLC. Refer to the D7024 Operation and Installation Guide (P/N: 31499)

for programming.

When configured as a Class “B” loop and installed on a D7024 Control Panel before Lot #100, the D7039

implements a Style 3.5 SLC. When installed on a D7024 Control Panel Lot #100 or later, the D7039

implements a Style 4 SLC. Refer to the D7024 Operation and Installation Guide (P/N: 31499) for programming.

2. Measure loop resistance by shorting the end of the farthest device in Class “B” (Figure 5) or shorting the return

wire in Class “A” (Figure 6) and reading the total resistance of all wires associated with the loop.

3. Ensure the loop is disconnected from the D7039 Module.

Bosch | 09/05 | 38685F6

D7039 | Installation Guide |Notes

4.0 Specifications

Table 1: Specifications

Input Voltage 24 VDC nominal from FACP

Current Draw, Standby

and Alarm

150 mA maximum

Current Draw Load 100 mA maximum for each bus

Maximum Bus Voltage 8.5 V to 13 V

Maximum Wiring

Resistance

50 Ω, Class A (Style 6) or Class B (Style 4) SLC

Environment Indoor/dry

Note: All Mux Bus terminals are power-limited and supervised.

7Bosch | 09/05 | 38685F

D7039 | Installation Guide | Notes

Notes

Bosch

130 Perinton Parkway

Fairport, NY 14450-9199 USA

Customer Service: (800) 289-0096

Technical Support: (888) 886-6189

38685F

Tabla de contenidos

Otros manuales de Unidad de control de Bosch

Bosch

Bosch ETT 223 Manual de usuario

Bosch

Bosch B520 Instrucciones de funcionamiento y mantenimiento

Bosch

Bosch SE352 Manual de usuario

Bosch

Bosch Rexroth LFA DB Series Manual de usuario

Bosch

Bosch Rexroth BVD 52 Series Manual de usuario

Bosch

Bosch Rexroth BTV 16 Manual técnico

Bosch

Bosch AMC2 4W-EXT Manual de usuario

Bosch

Bosch DS7432 Manual de usuario

Bosch

Bosch D192G Manual de usuario

Bosch

Bosch Professional GCY 42 Manual de usuario

Bosch

Bosch CM430S Cómo utilizar

Bosch

Bosch Rexroth IndraControl VCP 20.2 Manual técnico

Bosch

Bosch KTS 5 Series Manual de usuario

Bosch

Bosch REXROTH DBD Manual de usuario

Bosch

Bosch WPH Manual de usuario

Bosch

Bosch B426 Manual de usuario

Bosch

Bosch Heatronic 4000 Instrucciones de uso

Bosch

Bosch PowerBox PBX 190 Manual de usuario

Bosch

Bosch Control 8313 Manual de instrucciones

Bosch

Bosch Junkers MB LAN Manual de usuario

Bosch

Bosch API-AMC2-4WE Manual de usuario

Bosch

Bosch rexroth M1-16 Series Manual de usuario

Bosch

Bosch CL400 Manual de usuario

Bosch

Bosch rexroth 4WS2EM10 5X XH Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario