Bosch AMAX panel 2000 ICP-AMAX-P Manual de usuario

AMAX panel 2000 / AMAX panel 2000 EN

ICP-AMAX-P / ICP-AMAX-P-EN

en Installation Manual

ICP-AMAX-P / ICP-AMAX-P-EN 3

Bosch Sicherheitssysteme GmbH F.01U.241.127 | V4 | 2011.12

1 Graphics

GPRS

PSTN

TELEPHONE

NETWORK

CENTRAL

MONITORING

STATION

DX4020

ITS-DX4020-G

IUI-AMAX-

LCD8

IUI-AMAX-

LED8

BOSCH AMAX panel 2000 OVERVIEW

DX3010

BOSCH OPTION BUS

ICP-AMAX-P-EN

ICP-AMAX-P

B420/

4ICP-AMAX-P / ICP-AMAX-P-EN

F.01U.241.127 | V4 | 2011.12 Bosch Sicherheitssysteme GmbH

AMAX panel 2000 / AMAX panel 2000 EN Table of Contents | en 5

Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12

Table of Contents

1 Short Information 10

2SystemOverview 11

2.1 AMAX panel 2000 / AMAX panel 2000 EN Features 11

3 Installation 12

3.1 Quick start 12

3.1.1 Setting date and time 13

3.1.2 AMAX panel 2000 / AMAX panel 2000 EN Zone Defaults 14

3.2 System Special Status Definition 14

3.3 Programming 14

3.3.1 Programming with the AMAX Keypad 2000 14

3.3.2 Programming with the ICP-EZPK Programming key 16

3.3.3 Installer’s Programming Command 16

3.3.4 Default the control panel with the hardware 16

3.4 Prerequisites for an EN-conform Setup of the System 17

4UserGuide 19

4.1 Arming the System 22

4.1.1 Arming in AWAY mode 22

4.1.2 Arming in STAY mode 23

4.1.3 Forced arming 24

4.2 Disarming the System 24

4.2.1 Disarming with CODE 24

4.2.2 Disarming with wireless control Key 24

4.2.3 Disarming with Key switch 24

4.3 Faults or Tamper conditions 24

4.3.1 System fault or tamper analysis Mode 24

4.4 Walk test mode 25

4.5 Event Memory Recall mode 25

4.6 Reset the Control Panel 26

4.7 Bypassing 26

4.7.1 Bypassing Zones 26

4.7.2 Bypassing Faults and Tamper conditions (Except Zone Tampers) 27

4.8 Enable / Disable the installers code 27

4.9 Change individual code 27

4.10 Keypad alarm operation commands 27

4.10.1 Duress alarm 27

4.10.2 Keypad panic alarm 27

4.10.3 Keypad fire alarm 27

4.10.4 Keypad medical alarm 28

4.11 Domestic Dialing 28

4.11.1 Domestic Dialing Alarm 28

4.11.2 Confirming the Domestic call 28

6en | Table of Contents AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12 Installation Manual Bosch Sicherheitssysteme GmbH

5 Fault and Tamper Description 29

5.1 Accessory Modules Fail 30

5.1.1 Keypad 1 fail 30

5.1.2 Keypad 2 fail 31

5.1.3 DX3010 Fail 31

5.1.4 B420/DX4020/ITS-DX4020G Fail 31

5.2 Power Faults 32

5.2.1 AC Failure 32

5.2.2 Battery Failure 32

5.2.3 AUX Power Supply Fail 32

5.2.4 Bosch Option Bus Power Supply Fail 33

5.2.5 RF Power Supply Fail 33

5.3 Warning Device Failure 33

5.3.1 Warning Device 1 Disconnected 33

5.3.2 Warning Device 1 Short 34

5.3.3 Warning Device 2 Disconnected 34

5.3.4 Warning Device 2 Short 34

5.4 Telephone Line Fault 34

5.5 Date and Time Fail 35

5.6 Communication Failure 35

5.6.1 Communication Failure 1 35

5.6.2 Communication Failure 2 35

5.6.3 Communication Failure 3 35

5.6.4 Communication Failure 4 36

5.7 Tamper Condition 36

5.7.1 On Board Tamper 36

5.7.2 Keypad 1 Tamper 36

5.7.3 Keypad 2 Tamper 36

5.7.4 Keypad lock out 37

5.7.5 Sensor Tamper 37

5.7.6 Zone Tamper 37

5.8 External Fault 38

6 System Functions 39

6.1 Duress alarm 39

6.2 Siren Test 40

6.3 Fault and Tamper Analysis Mode 40

6.4 View date and time 40

6.5 Walk Test Mode 40

6.6 Event Memory Recall Mode 41

6.7 Reset panel/clear siren 41

6.8 Initiate a Modem Call 42

6.9 Send Test Report 42

6.10 Bypass Zones 42

6.11 Show Zone Type 42

6.12 Bypass all Faults and Tamper conditions (Except zone Tamper) 43

6.13 Enable Disable installer code user’s access 43

6.14 Change individual code 43

6.15 Setting date and time 43

AMAX panel 2000 / AMAX panel 2000 EN Table of Contents | en 7

Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12

6.16 Add/delete User Codes 44

6.17 Add/delete Radio User Codes 44

6.18 Change Domestic Phone Number 45

6.19 Enter Programming Mode 45

6.20 Command 959 – Exit from installer’s programming mode without saving the programming data 45

6.21 Command 960 – Exit from installer’s programming mode with saving the programming data 46

6.22 Command 961 – Reset the control panel to factory default settings 46

6.23 Command 962 – Copy the control panel memory to the programming key 46

6.24 Command 963 – Copy the programming key to the control panel 47

6.25 Command 999 – Display the software version number 47

6.26 Default the control panel with the hardware 47

7 System Informations 1 48

7.1 Zone Processing when arming 48

7.2 Zone Processing when disarming 48

7.3 Alarm processing 48

7.4 Software 49

7.4.1 Remote Connect 49

7.4.2 Remote Connect with Customer Control 49

7.4.3 Remote Connect with Callback Verification 49

7.4.4 Remotely Arm/Disarm System by Programming Softwares 50

7.5 Domestic Dialing 50

7.5.1 Domestic Dialing Function 50

7.6 Reporting Formats 50

7.6.1 Transmission Formats 50

7.6.2 Contact ID Format 50

7.6.3 CFSK Format 51

7.7 Dialer Information 51

7.7.1 Telephone number for Receiver 1 - 4/IP Address and Port 52

7.7.2 Other Network Programming Option 52

7.7.3 Report Transmission Sequence 53

7.7.4 Receiver 1 - 4 Transmission Format 53

7.7.5 Receiver 1 - 4 Subscriber ID Number 54

7.7.6 Call back Telephone Number 54

7.7.7 Ring Count 54

7.8 Access Codes 54

7.8.1 Installer Code 54

7.8.2 AMAX panel 2000 / AMAX panel 2000 EN User Codes 54

7.8.3 User Codes 55

8 System Informations 2 56

8.1 General overview on zones 56

8.1.1 Zone Inputs 56

8.1.2 Zone programming 57

8.1.3 Zone Types 57

8.1.4 Zone Bypass 62

8.1.5 Forced Arming 62

8.1.6 Silent Alarm 62

8.1.7 Zone Lockout 62

8en | Table of Contents AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12 Installation Manual Bosch Sicherheitssysteme GmbH

8.1.8 Zone Tamper 63

8.1.9 Zone Fault 63

8.1.10 Zone Report 63

8.1.11 Zone Chime Mode 63

8.2 System Reporting Information 63

8.2.1 System Option Programming Definition 64

8.2.2 System Report and Memory Definition 65

8.2.3 Auto Test Report 68

8.3 System Event Memory Recall 69

8.3.1 Keypad Play Back System Events 69

8.4 Output Process 69

8.4.1 Output Events Option 69

8.4.2 Output Type 72

8.4.3 Output Duration 72

8.4.4 Keypad Buzzer Alarm Output 72

8.4.5 Optional Relay Output 72

8.4.6 On-board LED Indicator 72

8.4.7 DX3010 Support 72

8.5 System Event Time 72

8.5.1 Entry Time 72

8.5.2 Exit Time 73

8.5.3 Keypad Lockout Time 73

8.5.4 System Power Up Wait Time 73

8.5.5 AC MAINS Fail Wait Time 73

8.6 Optional Equipment 73

8.6.1 RE012 E 2-Channel Hand-Held Keyfob 433 MHz 73

8.6.2 WE800E 433 MHz RF Receiver 73

8.6.3 ICP-EZPK Programming Key 73

8.6.4 A-Link Plus Software 73

8.6.5 DX3010 8 Relay Module 73

8.6.6 B420/DX4020/ITS-DX4020G GSM GPRS Communication Module 74

8.6.7 IUI-AMAX-LED8 8 Zone LED Keypad 74

8.6.8 IUI-AMAX-LCD8 8 Zone LCD Keypad 74

9 Technical Data 75

9.1 Specification 75

9.2 Interface Description 77

9.2.1 Terminals Internal Description 77

9.2.2 Connector Interface Description 77

10 Programming sheets 78

10.1 Receiver Programming 78

10.1.1 Receiver Parameters 78

10.1.2 Domestic Programming 79

10.2 System Report Options Programming 79

10.2.1 Report Options 79

10.2.2 Test Report Time Interval Setting 80

10.3 System Functions Programming 80

10.3.1 Ring Count 80

AMAX panel 2000 / AMAX panel 2000 EN Table of Contents | en 9

Bosch Sicherheitssysteme GmbH Installation Manual F.01U.241.127 | V4 | 2011.12

10.3.2 Remote Programming/Control 80

10.3.3 Call back Telephone Number 80

10.3.4 Exit Time 80

10.3.5 Entry Time 80

10.3.6 Keypad Lockout 81

10.3.7 Single Button STAY/AWAY ARM 81

10.3.8 Remote Arm by Software/Telephone 81

10.3.9 Arm by Keyfob 81

10.3.10 Force Arm as system is in trouble 81

10.3.11 Quick Emergency Alarm 81

10.3.12 Event Recall 81

10.3.13 OC1/Warning Device 1 Monitor 81

10.3.14 OC2/Warning Device 2 Monitor 81

10.3.15 Phone line Monitor 81

10.3.16 AC Fault Detect time 82

10.3.17 Battery Detect time 82

10.3.18 Event Record Count Per Set/Unset Period 82

10.3.19 Beep for Warning Devices 82

10.4 Zone Programming 82

10.5 Output Programming 85

10.5.1 Keypad Buzzer 85

10.5.2 Warning Device 1 / OC1 Output 85

10.5.3 Warning Device 2 / OC2 Output 85

10.5.4 Optional Relay Output / OC3 85

10.5.5 DX3010 Output 85

10.6 Installer/User Code Programming 87

10.6.1 Installer code 87

10.6.2 User Codes 87

11 Troubleshooting 89

10 en | Short Information AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12 Installation Manual Bosch Sicherheitssysteme GmbH

1 Short Information

Congratulations on selecting the AMAX panel 2000/AMAX panel 2000 EN for your installation.

Spend some time reading through this guide and familiarize yourself with the outstanding

operation and installation features of this system so that you can get the most from your unit.

In all aspects of planning, engineering, styling, operation, convenience and adaptability, we try

to anticipate your every possible requirement. Programming simplicity and speed are our

major considerations; we believe that our objectives have been attained.

This installation guide explains all aspects of programming the AMAX panel 2000/AMAX panel

2000 EN from factory default to final commissioning. All system parameters and options are

dealt with in detail, but adaptability differs with individuals. Each control panel can be

tailored to meet your requirements quickly and easily. The programming simplicity makes your

installation quick, accurate and rewarding.

As AMAX panel 2000/AMAX panel 2000 EN continue to improve over the years, they become

more powerful. We have addressed the needs of first-time users by maintaining simplicity in

the product and its installation guide, which enabled them in turn to evolve as "power users".

Otros manuales para AMAX panel 2000 ICP-AMAX-P

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel de control de Bosch

Bosch

Bosch D7412G Manual de usuario

Bosch

Bosch FPC-500 Manual de usuario

Bosch

Bosch FPA-5000 Manual de usuario

Bosch

Bosch Rexroth IndraControl VCP 25 Manual técnico

Bosch

Bosch D7212GV3 Guía de solución de problemas

Bosch

Bosch Rexroth IndraControl VDP 92.3 Manual técnico

Bosch

Bosch D9412GV4 Manual de usuario

Bosch

Bosch CPS21T Manual de usuario

Bosch

Bosch D7212GV3 Guía de inicio rápido

Bosch

Bosch D9412GV2 Manual de usuario

Bosch

Bosch D9412G Cómo utilizar

Bosch

Bosch D9412GV4 Instrucciones de funcionamiento

Bosch

Bosch ICP-CC404 Manual de usuario

Bosch

Bosch ICP-AMAX4-P1 Manual de usuario

Bosch

Bosch D7212GV2 Guía de inicio rápido

Bosch

Bosch B9512G Manual de usuario

Bosch

Bosch K2200 Series Manual de usuario

Bosch

Bosch ICP-SOL2-P Manual de usuario

Bosch

Bosch FPA-1000-UL Manual de usuario

Bosch

Bosch SOLUTION 3000 Manual de usuario

Bosch

Bosch Rexroth IndraControl VCP 20 Manual técnico

Bosch

Bosch FPA-5000 Guía del usuario

Bosch

Bosch Rexroth IndraControl VAM 11.1 Manual técnico

Bosch

Bosch ICP-CC488 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas

Truma

Truma CP plus Manual de usuario