Blue Ox BX2239 Manual de usuario

Page 1 of 8 292-2726 Rev. C 7/20/10

Please read BOTH these Installation Instructions and the General

Instructions before attempting to install or operate this equipment.

1. Blue Ox®towing products and accessories

are intended to be installed by Blue Ox®

Dealers who are familiar with our products and

have the equipment necessary and knowledge

to do “ﬁt work”. When necessary Blue Ox®

Dealers can be found at www.blueox.com or

by contacting our Customer Care

Department at (402) 385-3051.

2. Many Blue Ox®Baseplates are designed to

use existing holes and hardware to mount

the baseplate to the towed vehicle. Even

though bolts are there, do not assume they

are adequate for baseplate mounting. Always

use hardware supplied in the hardware kit

and existing hardware speciﬁed in the

Baseplate Installation Instructions.

Conﬁrm the towability and pre-towing

procedures for your vehicle with

the owner’s manual or contact the

vehicle’s manufacturer for speciﬁc

towing procedures.

Attachment Tab Height: 26 1/4”

Attachment Tab Width: 25”

2006-10 Honda

Ridgeline

Installation Instructions

BX2239

Bolt Size Grade 5 Grade 8

1/4” 10 14

5/16” 19 29

3/8” 33 47

7/16” 54 78

1/2” 78 119

5/8” 154 230

Bolt Torque Speciﬁcations

Torque in Foot-Pounds for Inch Bolts

Bolt Torque Speciﬁcations

Torque in Foot-Pounds for Metric Bolts

Bolt Size Grade 8.8 Grade 10.9

6MM 6 8

8MM 16 22

10MM 31 40

12MM 54 70

14MM 89 117

Serial Number

Failure to read and follow these instructions

could result in separation of the towed vehicle

from the tow bar, causing property damage,

loss of towed vehicle, personal injury or death.

WARNING

If the front of your vehicle looks different

than this, call us at (402) 385-3051.

Page 2 of 8 292-2726 Rev. C 7/20/10

Parts List

Ref. No. Qty. Part # Description

1 1 61-6127 Weldment, Baseplate, BX2239

2 4 61-5589 Nut Plate, 3/8-16 Nut, w/ 14” Wire

3 4 61-5208 Wld, Nut Plt 1/4X1X1, 3/8”/14”Wire

4 2 102-6682 Backing, Plate, BX1015

5 4 201-0418 8MM-1.25 X 35MM Hex Bolt Grd.8.8 ZP

6 4 203-0102 8MM Lock Washer, ZP

7 4 203-0002 5/16 Flat Washer, ZP

8 12 201-0440 3/8-16 X 1 1/2 Hex Bolt, Grd.5, ZP

9 12 203-0010 3/8 Lock Washer, ZP

10 4 203-0003 3/8 Flat Washer, ZP

11 4 202-0003 3/8-16 Hex Nut, ZP

12 2 201-0553 1/4-20 X 1/2 HX.Wshd.Type F Tcs, ZP

13 2 201-0192 10-32 X 1/2 Slot, RD. HD. Screw

14 2 203-0054 #10 Lock Washer

15 2 202-0047 #10-32 Hex Nut

16 2 101-5822 Adapter, 4 Way Connector

17 2 62-3468 Att TabAssy, Rem, SF/SB, 1 Hole

2 226-0046 Baseplate Safety Cable, 36” CL III (Not Shown)

4 229-0359 Quicklink, 3/8, ZP (Not Shown)

2 290-0437 Cap Plug, Black (Not Shown)

Important:

Use only genuine factory replacement parts on your baseplate. Do NOT substitute homemade or non-typical parts. If a bolt

is lost or in need of replacement, for your safety and the preservation of your baseplate, be sure to use a replacement bolt of

the same grade (In most cases it will be Grade 5, please reference the parts list above). Replacement parts may be ordered

through your nearest Blue Ox® Dealer or Distributor, or call our Customer Care Team at (402) 385-3051. Failing to follow

and/or altering these installation instructions in either installation or required equipment will void the manufacturer’s warranty.

Tools Required

8MM Socket

10MM Socket

12MM Socket

9/16” Socket

13/32” Drill Bit

Utility Knife

Phillips Screwdriver

Reciprocating Saw

Vise Grip

LOCTITE Red

2006-10 Honda Ridgeline

Installation Instructions

BX2239

Page 3 of 8 292-2726 Rev. C 7/20/10

Attachment Tabs:

Due to the design of the removable tabs, the

RangeFinder II and Ambassador tow bars can not

be used. Adapters, except the BX8833 and the

BX88151, can not be used with this baseplate.

Instructions:

The front fascia, headlights, horn bracket,

and bumper are removed for the baseplate

installation. Drilling is required. Trimming of

the air dam is required.

The dimensional variations between otherwise

identical vehicles can be considerable.

While the baseplate was designed for easy

installation, it may be necessary to tailor the

baseplate slightly to compensate for auto

manufacturer’s tolerances. These minor

adjustments may include ﬁling a hole slightly,

bending electrical rods or bending end plates.

The BX8869 Bulb and Socket Wiring Kit is

recommended for this vehicle.

1. Remove 12 pushpins from the plastic above the

radiator. Remove the plastic from the top of the

radiator. Set pushpins aside to reinstall later.

2. Just forward of the front tire, on the edge of the

fascia, use an 8MM socket or Phillips screwdriver

to remove one metric bolt. Set bolt aside to reinstall

later. Do this to both sides of the vehicle.



2006-10 Honda Ridgeline

Installation Instructions

BX2239



Installation Instructions:



Possible Location for the BX8869

Bulb and Socket Wiring Kit.

Handling of some cosmetic parts

when installing this product may

require the use of protective covers,

rags, specialty tools, etc. to prevent

damage.

Page 4 of 8 292-2726 Rev. C 7/20/10

3. Just forward of the front tire, on the outermost

bottom edge of fascia, remove two metric bolts

using a 10MM socket. Do this to both sides of the

vehicle. Set bolts aside to reinstall later.

6. Remove another push pin from underneath, gray

arrow. Remove the two bolts on the side. Using

a 12MM socket, remove the bolt from the horn

bracket, bottom arrow. Do this to both sides of the

vehicle. Set push pins and bolts aside to reinstall

later.



4. Using a 10MM socket, remove three metric bolts

that run horizontally along the bottom of fascia,

where the belly pan and fascia meet. Set bolts

aside to be reinstalled later.



5. Remove the metric bolt, using an 10MM socket.

Also remove the push pin above the headlight, gray

arrow. Do this to both sides of the vehicle. Set

bolts and push pins aside to reinstall later. Start

fascia removal by pulling down on the fascia where

it meets the fender, just forward of the front tire.

While still on the side of the vehicle, pull fascia

slightly forward. Do the steps above to both sides

of the vehicle. From the front of the vehicle, pull

fascia forward to remove. Set fascia aside carefully

to reinstall later.

2006-10 Honda Ridgeline

Installation Instructions

BX2239



7. Remove this bolt on the side. Do this to both sides

of the vehicle. Set bolts aside to reinstall later.

Page 5 of 8 292-2726 Rev. C 7/20/10

2006-10 Honda Ridgeline

Installation Instructions

BX2239



8. Using a Phillips screwdriver, remove the screw. Do

this to both sides of the vehicle.



10. Lay the bracket of the metal bumper on a solid

surface. Use a hammer to pound and ﬂatten the rib

on top of the bracket. Do this to both sides of the

vehicle.

9. Using a 12MM socket, remove two metric bolts on

the top and one metric bolt underneath the metal

bumper. Do this to both sides of the vehicle. Set

bolts aside to reinstall later.



When using power drills be aware of the

dangers of torque and drill bit length.

Page 6 of 8 292-2726 Rev. C 7/20/10

12. Using a vice grip; clamp the rear of the baseplate

to the webbing. Using the baseplate as a template,

drill into the frame rail through the three baseplate

holes using a 13/32” drill bit. Remove the two bolts

and pull the bolt out of the bottom. Remove the

bumper. Line up the baseplate with the back hole.

Guide a 3/8-16 nut plate through the frame opening

and align with bolt hole. Insert the 3/8-16 hex bolt

into those bolt holes with the 3/8 lock washer and

hand tighten. Do this on both sides of the vehicle.

Be sure to use LOCTITE Red on ALL bolts.



2006-10 Honda Ridgeline

Installation Instructions

BX2239



13. Temporarily slide the metal bumper in between the

frame and the baseplate. Insert additional bolts

and tighten using Loctite. Torque to specs. Do this

on both sides. Drill the side hole being sure not to

drill into the radiator, use a socket over the drill bit.

BE SURE TO USE LOCTITE®RED ON ALL BOLTS

BEFORE TIGHTENING. TIGHTEN ALL BOLTS

ACCORDING TO THE TORQUE CHART ON THE FRONT

PAGE OF THESE INSTRUCTIONS OR ON PAGE 3 OF

THE BASEPLATE TOWING GENERAL INSTRUCTIONS.



11.Slide metal bumper back on to the frame rail,

guiding the baseplate on top of frame rail. Align

with the existing holes of the bumper bracket.

Insert two 8MM-1.25 x 30MM hex bolts through

the baseplate into the two existing bumper bracket

holes using 5/16” lock washer and 5/16” ﬂat

washers Snug the bolts down. Do this on both

sides.



14. Remove metal bumper. Insert the 3/8-16 hex bolts

with the 3/8” lock washer through the baseplate

holes on the side of the frame rail. Hand tighten

bolts to the 3/8-16 nut plates placed on hex bolts

through opening in frame end. Do this to both

sides of the vehicle. Using diagonal cutters, cut

all nut plate wires ﬂush with the end of the frame.

Reinstall bumper and tighten bolt for steps 12, 13

and 14. Be sure to apply LOCTITE Red to ALL

bolts.



Page 7 of 8 292-2726 Rev. C 7/20/10

2006-10 Honda Ridgeline

Installation Instructions

BX2239

18. Just outside the driver’s side radiator, trim the air

dam up 1 1/2”, follow the top of the ridge all the

way across.



17. Reinstall the horns using the 12MM socket. Put

the headlight assemblies back on and plug in. Do

this to both sides of the vehicle.



15. Insert the 3/8-16 hex bolts with the 3/8” lock

washer through the baseplate holes on the side

of the radiator support. Then tighten bolts to the

3/8-16 nut plates on back side of radiator support.

Do this to both sides of the vehicle. Using diagonal

cutters, cut all nut plate wires ﬂush with the end of

the frame. Be sure to apply LOCTITE Red to ALL

bolts.



19. Trim 4 1/2” across, leave the tab by cutting below

the tab.



16. Place the backing plate on the bottom side of the

frame webbing to align with drilled holes, insert

the 3/8-16 x 1 1/2” hex bolts and 3/8” ﬂat washers

into this hole, tighten the 3/8-16 hex nuts and 3/8”

lock washers. Reinstall the air bafﬂe to its original

position.

Install the tow bar and safety cables according

to their instructions. When demonstrating this to

the customer, be sure to include all of the Blue Ox

packaging and contents.

Reinstall fascia. Be sure to install all pushpins and

bolts.

Baseplate Installation is now Complete.

CUSTOMER SERVICE COMMITMENT

Blue Ox is committed to providing you with

exceptional customer care throughout your lifetime

with our products. Our team is here to assist you

with any questions you may have regarding the

performance of your product. Simply call (402)

385-3051 and you can speak with our customer

care team.

Additionally, please visit our website to see

which rallies our Destination America team will

be attending. For a nominal fee, our service

technician will service your towing system to

ensure it’s in proper working condition. Also as

a commitment to our customers, should you visit

our factory you can stay at our full service Blue

Ox campground at no charge along with enjoying

a factory tour.

Again thank you for being our customer and for

the conﬁdence you have shown in the performance

of our products. It is because of customers like

you we enjoy the success we have today.

One Mill Road, Industrial Park

Pender, Nebraska 68047

Phone: (402) 385-3051

Toll Free: (888) 425-5382

Fax: (402) 385-3360

www.blueox.com

Page 8 of 8 292-2726 Rev. C 7/20/10

With removable tabs installed.

2006-10 Honda Ridgeline

Installation Instructions

BX2239

Be sure that ALL electrical connections

are plugged in properly and functioning

BEFORE Installing the fascia.

DEALER OR INSTALLER:

Be certain the user receives the

instruction sheets for their products.

If the baseplate is in an accident, it must

be replaced. DO NOT use it again! An

accident can cause unseen damage and

using it again could result in more dam-

age or serious injury. DO NOT use the

baseplate if it is damaged or missing parts.

Tabla de contenidos

Otros manuales de Accesorios para automóviles de Blue Ox

Blue Ox

Blue Ox BX1504 Manual de usuario

Blue Ox

Blue Ox BX1958 Manual de usuario

Blue Ox

Blue Ox DH2303 Manual de usuario

Blue Ox

Blue Ox BX1502 Manual de usuario

Blue Ox

Blue Ox BX3781 Manual de usuario

Blue Ox

Blue Ox AVENTA II Manual de usuario

Blue Ox

Blue Ox BX1136 Manual de servicio

Blue Ox

Blue Ox BX88420 Manual de usuario

Blue Ox

Blue Ox BX3216 Manual de usuario

Blue Ox

Blue Ox BX1126 Manual de usuario

Blue Ox

Blue Ox BX8847 Manual de usuario

Blue Ox

Blue Ox SwayPro BXW0553 Manual de usuario

Blue Ox

Blue Ox BX4102 Manual de usuario

Blue Ox

Blue Ox SportCarrier II Hoja de especificaciones

Blue Ox

Blue Ox BedSaver BXR4502 Manual de usuario

Blue Ox

Blue Ox BX2711 Manual de usuario

Blue Ox

Blue Ox ADVENTURER BX7322 Manual de usuario

Blue Ox

Blue Ox BX1133 Manual de usuario

Blue Ox

Blue Ox BX1681 Manual de usuario

Blue Ox

Blue Ox BX2177 Manual de usuario

Blue Ox

Blue Ox BX3775 Manual de usuario

Blue Ox

Blue Ox TRION BX7520P Manual de usuario

Blue Ox

Blue Ox BX7365 Manual de usuario

Blue Ox

Blue Ox BX1120 Manual de usuario

Manuales populares de Accesorios para automóviles de otras marcas

James Baroud

James Baroud Odyssey Manual de usuario

Motorola

Motorola i50sx Manual de usuario

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manual de usuario

Feniex

Feniex T3 Manual de usuario

Renault

Renault 77 11 423 180 Manual de usuario

Kia

Kia E8300-4D000 Manual de usuario

Brink

Brink 756843 Manual de usuario

Whispbar

Whispbar K085W Manual de usuario

v.link

v.link CI-VL2-PC-HSD Manual de usuario

Viking

Viking Stack-Rack Guía de configuración rápida

Aries

Aries 203015 Manual de usuario

Choetech

Choetech AT0005 Manual de usuario

ZZ2

ZZ2 ZZAIR-PRO Manual de usuario

Holman

Holman 4A80L Manual de usuario

Thule

Thule 2075 Manual de usuario

Motorola

Motorola T325 Manual de usuario

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guía de instalación

DV8

DV8 FBJL-02 Manual de usuario