Blizzard Lighting Motif Risplendi 150 Manual de usuario

Blizzard Lighting, LLC

http://www.blizzardpro.com

Waukesha, WI USA

Page 2

TABLE OF CONTENTS

1. Getting Started 3

What’s In The Box? 3

Getting It Out Of the Box 3

Powering Up! 3

Getting A Hold Of Us 3

Safety Instructions 4

2. Meet the Motif™ Risplendi 150 5

Main Features 5

Motif™ Risplendi 150 Pin-Up Picture 6

The Rear Connections 6

3. Setup 7

Fuse Replacement 7

Power Input 7

Connecting the Fixtures 7

Cable Connectors 8

3-Pin??? 5-Pin??? Huh?!? 8

Take It To The Next Level: Setting Up DMX Control 8

Changing the Lenses 9

Installing or Removing Brackets 9

Mounting & Rigging 9

4. Operating Adjustments 10

The Control Panel 10

Control Panel Menu Structure 11

DMX Mode 12

Dimming Mode Settings 12

Custom Programs 13

Auto, Modes, and Auto Speed 13

Color Calibration Settings 14

Custom Static Colors & Preset Colors 14

Fixture Reset Functions 15

Data Sync Feature 15

Fixture Information 15

DMX Values In-Depth 16

Troubleshooting 17

5. Appendix 18

Keeping Your Motif™ Risplendi As Good As New 18

Returns (Gasp!) 18

Shipping Issues 18

Tech Specs! 19

Dimensional Drawings 20

Page 3

1. GETTING STARTED

What’s In The Box?

• Motif™ Risplendi 150

• Power cable

• 4x interchangeable lenses

• This user manual

Optional Accessories (sold separately)

The Motif™ Risplendi 150 allows for an optional full snoot accessory which can

enhance the light's output control by concentrating its beam spread. Contact

your authorized Blizzard Lighting dealer for pricing.

• Black Housing: SNOOT-Motif Risplendi (B)

• White Housing: SNOOT-Motif Risplendi (W)

• Space Gray Housing: SNOOT-Motif Risplendi (SG)

Getting It Out Of the Box

Congratulations on purchasing the Motif™ Risplendi 150. Now that you’ve got

your xture, you should carefully unpack the box and check the contents to

ensure that all parts are present and in good condition. If anything looks as if

it has been damaged in transit, notify the shipper immediately and keep the

packing material for inspection. Again, please save the carton and all packing

materials. If a xture must be returned to the factory, it is important that the

xture be returned in the original factory box and packing.

Powering Up!

All xtures must be powered directly o a switched circuit and cannot be run

o a rheostat (variable resistor) or dimmer circuit, even if the rheostat

or dimmer channel is used solely for a 0% to 100% switch.

Warning! All xtures must be connected to circuits with a suitable

Ground (Earthing).

Getting A Hold Of Us

If something happens to go wrong, visit blizzardpro.com/support and

open a support ticket. We’ll be happy to help, honest.

Disclaimer: The information contained in this document are subject to change without

notice. Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions

that may appear in this user manual. We reserve the right to update the existing, or create

a new document to correct any errors or omissions at any time. You can download the

latest version of this document from www.blizzardpro.com.

Author: Date: Last Edited: Date:

J. Thomas 6/13/2023 J. Thomas 6/27/2023

Page 4

Please read these instructions carefully. They include

important information about the installation, usage and

maintenance of this product.

Safety Instructions

• Please keep this User Guide for future use. If you sell the unit to someone

else, be sure that they also receive this User Guide.

• ALWAYS make sure that you are connecting to the proper voltage, and that

the line voltage you are connecting to is not higher than that stated on the de-

cal or rear panel of the xture.

• This product is intended for indoor use only.

• To prevent risk of re or shock, do not expose xture to rain or moisture.

• Make sure there are no ammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least

20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are

blocked.

• ALWAYS disconnect from the power source before servicing or replacing fuse

and be sure to replace with same fuse size and type.

• ALWAYS secure xture using a safety chain. NEVER carry the xture by its

head. Use its carrying handles.

• DO NOT operate at ambient temperatures higher than 104°F (40°C).

• In the event of a serious operating problem, stop using the unit immediately.

NEVER try to repair the unit by yourself. Repairs carried out by unskilled people

can lead to damage or malfunction. Please contact the nearest authorized tech-

nical assistance center. Always use the same type spare parts.

• NEVER connect the device to a dimmer pack.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Caution! There are no user serviceable parts inside the unit. Do not open the

housing or attempt any repairs yourself. In the unlikely event your unit may

require service, please open a support ticket at www.blizzardpro.com/support.

Page 5

2. MEET THE MOTIF™ RISPLENDI 150

Main Features

• Light source: 150W RGBAL COB LED, 100,000 hrs.

• Built-in color & chase macros via DMX

• Built-in automated programs via master/slave

• Color mixing ability in standalone mode

• 4x light collimating lenses (30°, 45°, 60°, 80°)

• Convection cooled aluminum housing

• Dual mounting brackets for positioning exibility

• Adjustable LED refresh rates (1200Hz-20KHz)

• PowerCON® TRUE1™ compatible + hardwire AC connector

• Emergency power backup connector (42-48V DC, 20W)

• 5-pin male/female XLR input & output connections

Control

• Protocol: USITT DMX-512, RDM

• DMX channels: 5/7/11-channels

• OLED control menu with 4x touch sensitive buttons

• Operating modes: DMX512, master/slave, auto

DMX Quick Reference (5-Channel Mode)

Channel What is does...

1 Red Intensity (0 <--> 100%)

2 Green Intensity (0 <--> 100%)

3 Blue Intensity (0 <--> 100%)

4 Amber Intensity (0 <--> 100%)

5 Lime Intensity (0 <--> 100%)

DMX Quick Reference (7-Channel Mode)

Channel What is does...

1 Master Dimmer (0 <--> 100%)

2 Red Intensity (0 <--> 100%)

3 Green Intensity (0 <--> 100%)

4 Blue Intensity (0 <--> 100%)

5 Amber Intensity (0 <--> 100%)

6 Lime Intensity (0 <--> 100%)

7 Strobe (Slow <--> Fast)

DMX Quick Reference (11-Channel Mode)

Channel What is does...

1 Master Dimmer (0 <--> 100%)

2 Red Intensity (0 <--> 100%)

3 Green Intensity (0 <--> 100%)

4 Blue Intensity (0 <--> 100%)

5 Amber Intensity (0 <--> 100%)

6 Lime Intensity (0 <--> 100%)

7 Strobe (Slow <--> Fast)

8 Built-In Programs

9 Auto Speed (Slow <--> Fast)

10 Virtual Color Wheel

11 32-Bit Dimming

Page 6

Motif™ Risplendi 150 Pin-Up Picture

The Rear Connections

EMERGENCY

POWER DC: 40-48V

V-

V+

DMX IN

EXT.POWER IN

EXT INT

POWER SWITCH

EXT/INT.POWER IN

AC:100-240V 50Hz-60Hz

SAFETY

FUSE

INT.POWER

DMX OUT

Ext./Int.

Power Switch

4-Button

Control Menu

DMX In/OutExt. Power In

Emergency

Power

Int. Power In

150W RGBAL LED

Light Source

Locking

Knob

Anodized Aluminum

Housing

Vertical

Bracket

Adjustable

Bracket

Safety Loop

Page 7

Fuse Replacement

Remove the fuse holder from of its housing. Take out the damaged fuse from its

holder and replace with exact same type of fuse.

Power Inputs

This xture comes with a powerCON® TRUE1™ compatible power input and a

3-wire power terminal block connector located under the "Int. Power In" cover

plate on the rear of the xture that can be used for hardwiring power.

Depending on which method you use, adjust the external/internal power switch

on the back of the unit to select the proper input source.

Before replacing the fuse, disconnect the power cord.

ALWAYS replace it with the same type and rating.

3. SETUP

Connecting the Fixtures

Fixtures on a serial data link must be daisy chained in one single line. Also,

connecting more than 32 xtures on one serial data link without the use of a

DMX optically-isolated splitter may result in deterioration of the signal.

Data/DMX Cabling

To link xtures together you’ll need data cables. You should use data-grade

cables that can carry a high quality signal.

The data cable should have the following characteristics:

• 2-conductor twisted pair plus a shield

• Maximum capacitance between conductors – 30 pF/ft.

• Maximum capacitance between conductor & shield – 55 pF/ft.

• Maximum resistance of 20 ohms / 1000 ft.

• Nominal impedance 100 – 140 ohms

Connection Wire (U.S.) Wire (Europe) Screw Color

AC Live Black Brown Yellow or Brass

AC Neutral White Blue Silver

AC Ground Green/Yellow Green/Yellow Green

Use the table below for reference when using the bare wire:

Page 8

Cable Connectors

Cables must have a male XLR connector on one end and a female XLR connec-

tor on the other end. (Duh!)

To build your own DMX Terminator:

Obtain a 120-ohm, 1/4-watt resistor, and wire it between pins 2 & 3 of the last xture. They are also

readily available from specialty retailers.

Take It To The Next Level: Setting Up DMX Control

Step 1: Connect the male connector of the DMX cable to the female connector

(output) on the controller.

Step 2: Connect the female connector of the

DMX cable to the rst xture’s male connector

(input).

Note: It doesn’t matter which xture address is the rst one

connected. We recommend connecting the xtures in terms

of their proximity to the controller, rather than connecting the

lowest xture number rst, and so on.

Step 3: Connect other xtures in the chain

from output to input as above. Place a DMX

terminator on the output of the nal xture to

ensure best communication.

CAUTION: Do not allow contact between the common and the xture’s chassis

ground. Grounding the common can cause a ground loop, and your xture may

perform erratically. Test cables with an ohm meter to verify correct polarity and

to make sure the pins are not grounded or shorted to the shield or each other.

3-Pin??? 5-Pin??? Huh?!?

If you use a controller with a 3-pin DMX output connector, you will need to use a 3-pin to 5-pin adapter. If

you’d like to build your own, the chart below details a proper cable conversion:

Conductor 3-Pin Female (Output) 5-Pin Male (Input)

Ground/Shield Pin 1 Pin 1

Data 1- (Primary Data) Pin 2 Pin 2

Data 1+ (Primary Data) Pin 3 Pin 3

Data 2- (Optional) -- Pin 4 - Do Not Use

Data 2+ (Optional) -- Pin 5 - Do Not Use

INPUT OUTPUT

DMX OUTDMX IN

First

Fixture

in Chain

Fixture

in Chain

DMX OUTDMX IN

A Word on Termination:

DMX is a resilient communication protocol, however

errors still occasionally occur. Termination reduces signal

errors, and therefore best practices include use of a

terminator in all circumstances. If you are experiencing

problems with erratic xture behavior, especially over

long signal cable runs, a terminator may help improve

performance.

Page 9

Thumbscrew

Lens Holder Brackets

Snoot

(sold separately)

Installing or Removing Brackets

1.) Install or remove the brackets as shown above us-

ing the included bolts, washers, and knobs.

2.) Use the small bracket for vertically mounted xed

installations. You can remove the large bracket in these

types of applications, and use the included plastic

plugs to cover the bracket screw holes.

Changing the Lenses

This xture comes with a pre-installed 80° diuser lens plus 3x replaceable

Fresnel lenses (30°, 45°, and 60°) for a variety of beam angles.

To change the lens, remove the thumbscrew from the lens holder and swivel

the holder outwards. Replace the existing lens with the lens of your choice.

Note: The replaceable lenses need to be installed with the circular pattern side

of the lens facing outwards.

*When using lenses with narrower beam angles, some chromatic aberration

(color separation) may occur. We recommend using the snoot accessory (sold

separately) to cut o the beam edge. This may help in certain circumstances.

Mounting & Rigging

This xture may be mounted in any SAFE position pro-

vided there is enough room for ventilation.

Mount the xture using a suitable "C" or "O" type

clamp. The clamp should be rated to hold at least 10x the xture’s weight to

ensure structural stability. Do not mount to surfaces of unknown strength,

ensure properly rated rigging is used, and always secure your xtures with a

safety cable.

Page 10

4. OPERATING ADJUSTMENTS

The Control Panel

All of the features and dierent modes possible with this xture are accessed

by using the control panel on the front of the xture. There are 4 control but-

tons next to the menu display which allow you to navigate through the various

control panel menus.

<MENU>

Is used to navigate to the previous higher-level menu item.

<ENTER>

Is used to select and conrm/store the current selection.

<UP>

Scrolls through menu items and numbers in ascending order.

<DOWN>

Scrolls through menu items and numbers in descending order.

The control panel display shows the menu items you select from the menu map

on page #11. When a menu function is selected, the display will show immedi-

ately the rst available option for the selected menu function. To select a menu

item, press <ENTER>.

Use the <UP> and <DOWN> buttons to navigate the menu options. Press the

<ENTER> button to select the menu function currently displayed, or to enable

a menu option. To return to the previous option or menu without changing the

value, press the <MENU> button.

Tabla de contenidos

Otros manuales de Equipo de iluminación de Blizzard Lighting

Blizzard Lighting

Blizzard Lighting mikrokassette Manual de usuario

Blizzard Lighting

Blizzard Lighting ToughStick 5 Manual de usuario

Blizzard Lighting

Blizzard Lighting G-Max 150 Manual de usuario

Blizzard Lighting

Blizzard Lighting Switch Blade X3 Manual de usuario

Blizzard Lighting

Blizzard Lighting the puck Manual de usuario

Blizzard Lighting

Blizzard Lighting Node:b RGBAL Manual de usuario

Blizzard Lighting

Blizzard Lighting The Puck 3NX Manual de usuario

Blizzard Lighting

Blizzard Lighting Torrent F3 Manual de usuario

Blizzard Lighting

Blizzard Lighting COLORISE Exa Manual de usuario

Blizzard Lighting

Blizzard Lighting PixelStorm COB Mini Manual de usuario

Blizzard Lighting

Blizzard Lighting Lo-Pro Flux Manual de usuario

Blizzard Lighting

Blizzard Lighting HotBox RGBW/RGBA Manual de usuario

Blizzard Lighting

Blizzard Lighting THE PUCK RGBA LED PAR Can Manual de usuario

Blizzard Lighting

Blizzard Lighting ROCKER PANEL RGBAW Manual de usuario

Blizzard Lighting

Blizzard Lighting Motif Metro Manual de usuario

Blizzard Lighting

Blizzard Lighting PixlStik Manual de usuario

Blizzard Lighting

Blizzard Lighting BladeRunner RGBW Manual de usuario

Blizzard Lighting

Blizzard Lighting Flurry Spot Manual de usuario

Blizzard Lighting

Blizzard Lighting ICE 30 Manual de usuario

Blizzard Lighting

Blizzard Lighting Colorise Quadra Manual de usuario

Blizzard Lighting

Blizzard Lighting Flurry TRI Manual de usuario

Blizzard Lighting

Blizzard Lighting MAX L Manual de usuario

Blizzard Lighting

Blizzard Lighting Tour QT Skywire Manual de usuario

Blizzard Lighting

Blizzard Lighting ProPar V12 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario