Blizzard Lighting ICE 30 Manual de usuario
Blizzard Lighting, LLC
www.blizzardlighting.com
Wisconsin, USA
Copyright (c) 2012
Page 2
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
TABLE OF CONTENTS
ICE 30™ 30W LED Moving Head Spot 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The ICE 30™ Spot 5
Features 5
DMX Quick Reference 5
The ICE 30 Pin-up Picture 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of ICE 30’s™ 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9
UsingthisxturewiththewiCICLE®WirelessDMXSystem 10
4. Operating Adjustments 12
The Control Panel 12
Control Panel Menu Structure & Adjustments 12
Setting the pan/tilt/Menu to inverting or non-inverting 12
SettingtheDMXchannelconguration 12
Setting the maximum pan angle 12
Setting the maximum tilt angle 12
Additional User Adjustments 12
Service Functions 13
Resettingthexture 13
Restoring Factory Defaults 13
Stand-Alone (“Auto”) Mode 13
Master/Slave (“Auto” or “Sound Active”) 13
DMX Mode 13
Gobo Replacement 13
DMX Channel Values In-Depth 14
Troubleshooting 16
5. Appendix 17
A Quick DMX Lesson 17
Keeping Your ICE 30 Spot As Good As New 18
Returns (Gasp!) 18
Shipping Issues 18
Tech Specs 19
Page 3
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
•1xICE30™Spot
•AnEver-So-HandyPowerCord
•ASweetSafetyCable&setofMountingBrackets
•ThisLovelyUserManual
Getting It Out Of The Box
You’reascooollldasice...butnotwillingtosacriceyourlove...fora
greatLEDmovingheadxture!Nowthatyou’vegotyourICE30,you
should carefully unpack the box and check the contents to ensure that
all parts are present and in good condition. If anything looks as if it
has been damaged in transit, notify the shipper immediately and keep
the packing material for inspection. Again, please save the carton and
allpackingmaterials.Ifaxturemustbereturnedtothefactory,itis
importantthatthexturebereturnedintheoriginalfactoryboxand
packing.
Powering Up!
Allxturesmustbepowereddirectlyoffaswitchedcircuitandcannot
be run off a rheostat (variable resistor) or dimmer circuit, even
if the rheostat or dimmer channel is used solely for a 0% to
100% switch.
AC Voltage Switch -Notallxtureshaveavoltageselectswitch,so
pleaseverifythatthextureyoureceiveissuitableforyourlocalpow-
ersupply.Seethelabelonthextureorrefertothexture’sspeci-
cationschartformoreinformation.Axture’slistedcurrentratingis
itsaveragecurrentdrawundernormalconditions.Checkthextureor
device carefully to make sure that if a voltage selection switch exists
that it is set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit
matches the line voltage applied. Damage to your xture may
result if the line voltage applied does not match the voltage
indicated on the voltage selector switch. All xtures must be
connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email.
We’ll be happy to help, honest.
Blizzard Lighting
W220 N1531 Jericho Ct. Suite E, Waukesha, WI 53186 USA
www.blizzardlighting.com
Page 4
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
•PleasekeepthisUserGuideforfutureuse.Ifyouselltheunittosomeone
else, be sure that they also receive this User Guide.
•ALWAYSmakesurethatyouareconnectingtothepropervoltage,andthat
the line voltage you are connecting to is not higher than that stated on the de-
calorrearpanelofthexture.
•Thisproductisintendedforindooruseonly.
•Topreventriskofreorshock,donotexposexturetorainormoisture.
•Makesuretherearenoammablematerialsclosetotheunitwhileoperating.
•Theunitmustbeinstalledinalocationwithadequateventilation,atleast
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
•ALWAYSdisconnectfromthepowersourcebeforeservicingorreplacingfuse
and be sure to replace with same fuse size and type.
•ALWAYSsecurextureusingasafetychain.NEVERcarrythexturebyits
head. Use its carrying handles.
•DONOToperateatambienttemperatureshigherthan104°F(40°C).
•Intheeventofaseriousoperatingproblem,stopusingtheunitimmediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized tech-
nical assistance center. Always use the same type spare parts.
•NEVERconnectthedevicetoadimmerpack.
•Makesurethepowercordisnevercrimpedordamaged.
•Neverdisconnectthepowercordbypullingortuggingonthecord.
•Avoiddirecteyeexposuretothelightsourcewhileitison.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
yourunitmayrequireservice,pleasecontactBlizzardLightingatsup-
Page 5
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
2. MEET THE ICE 30™SPOT
CONTROL FEATURES
• 10 or 15-channel DMX LED moving yoke
• Pan: 540º/360º/180º Tilt: 270º/180º/90º
• Color wheel: 7 colors + white
• Rainbow color spin at variable speeds
• Rotating gobo wheel with gobo shake
• 6 interchangeable, rotating slot-n-lock gobos + open (1 glass installed)
• 8xedgobos
• Gobo wheel spin at variable speeds
• 3-facet rotating prism
• Variable electronic strobe
• Variable electronic dimmer (0 – 100%)
• RemotefocusviaDMX(2m~innity)
• Remotexturereset
• Multiple built-in automated & sound activated programs
ADDITIONAL FEATURES
• Lux: 5,300 @ 1m
• Gobo size: 27.9mm outside, 23mm image, 1.2mm max thickness
• Beam Angle: 14º
• Light source: 30W White LED, 50,000 hrs
DMX Quick Reference
Channel What It Does... (15 Chan-
nel)
(10 Channel Mode)
1Pan Pan
2 Tilt Tilt
3 Pan Fine (16-Bit) Color
4 Tilt Fine (16-Bit) Fixed Gobos
5 Motor Speed Rotating Gobos
6 Color Gobo Rotation
7 Fixed Gobos Strobe
8 Rotating Gobos Dimmer
9 Gobo Rotation Prism
10 Shutter/Strobe Focus
11 Dimmer
12 Functions
13 Movement Macros
14 Prism
15 Focus
Page 6
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
Figure 1: The ICE 30 Pin-Up Picture
Lens
Control Panel
LCD
Readout
Head
Figure 2: The Rear Connections
AC Power
Fuse Cover
DMX In DMX Out
Microphone
DMX Indicator
Fan Guard
Page 7
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
Withaatheadscrewdriver,wedgethe
fuse holder out of its housing. Remove the
damaged fuse from its holder and replace
with exact same type fuse. Insert the fuse
holder back in its place and reconnect
power.
Connecting A Bunch of ICE 30™eseses
You will need a serial data link to run light shows using a DMX-512
controllerortorunshowsontwoormorexturessettosyncinmas-
ter/slaveoperatingmode.Thecombinednumberofchannelsrequired
byallthexturesonaserialdatalinkdeterminesthenumberofx-
tures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also,connectingmorethan32xturesononeserialdatalinkwithout
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft).Themaximumrecommendednumberofxturesonaserialdata
linkis32xtures.
Data/DMX Cabling
Tolinkxturestogetheryou’llneeddatacables.Youshouldusedata-
gradecablesthatcancarryahighqualitysignalandarelessproneto
electromagnetic interference.
Forinstance,Belden©9841meetsthespecicationsforEIARS-485
applications. Standard microphone cables will “probably” be OK, but
note that they cannot transmit DMX data as reliably over long distanc-
es. In any event, the cable should have the following characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Page 8
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION:Donotallowcontactbetweenthecommonandthex-
ture’s chassis ground. Grounding the common can cause a ground
loop,andyourxturemayperformerratically.Testcableswithan
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers If you’d like to build your own, the
chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of the
DMXcabletotherstxture’smaleconnec-
tor (input). Note: It doesn’t matter which
xtureaddressistherstoneconnected.
Werecommendconnectingthexturesin
terms of their proximity to the controller,
ratherthanconnectingthelowestxture
numberrst,andsoon.
Step 3:Connectotherxturesinthechain
from output to input as above. Place a DMX
terminatorontheoutputofthenalxture
to ensure best communication.
Page 9
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
therstxture.
2. Connect the end of the cable coming from the
rstxturewhichwillhavea(female)3pinconnec-
tortotheinputconnectorofthenextxturecon-
sisting of a (male) 3 pin connector. Then, proceed
to connect from the output as stated above to the
inputofthefollowingxtureandsoon.
A quick note: Often,
the setup for Master-
Slave and Standalone
operationrequiresthat
therstxtureinthe
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily,thextures
that follow may also re-
quireaslavesetting.
Check the “Operating Adjustments” section in this manual for com-
pleteinstructionsforthistypeofsetupandconguration.
Mounting & Rigging
ThisxturemaybemountedinanySAFEpositionprovidedthereis
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xtureusingasuitable“C”or“O”typeclamp.Theclampshouldbe
ratedtoholdatleast10xthexture’sweighttoensurestructuralsta-
bility. Do not mount to surfaces with unknown strength, and ensure
properly“rated”riggingisusedwhenmountingxutresoverhead.
Adjusttheangleofthexturebylooseningbothknobsandtiltingthe
xture.Afterndingthedesiredposition,retightenbothknobs.
•Whenselectinginstallationlocation,takeintoconsiderationlamp
replacement access (if applicable) and routine maintenance.
•SafetycablesMUSTALWAYSbeused.
•Nevermountinplaceswherethexturewillbeexposedtorain,
high humidity, extreme temperature changes or restricted ventilation.
Page 10
ICE 30 Manual Rev. C Copyright (c) 2012 Blizzard Lighting, LLC
USING THIS FIXTURE WITH THE wiCICLE® WIRELESS
DMX SYSTEM
In addition to the unbridled thrill you al-
readyreceivedthersttimeyouplugged
inyourxture,you’llbedelightedtoknow
thatThisxturealsoworksseamlesslywith
our wiCICLE®Wireless DMX system, without additional power.
•ONLYxturesbearingthislogoarecertiedforusewiththewiCI-
CLE®without external power.
• Unauthorized modication and/or using the wiCICLE®with
unapproved xtures may cause damage to the wiCICLE®or
xture. UNDER NO CIRCUMSTANCES IS BLIZZARD LIGHTING
RESPONSIBLE FOR ANY DAMAGE FROM SUCH OPERATION.
•FixturesbearingtheabovelogoMUST only use cable and connec-
tors which separate chassis/case ground from cable shielding. Cabling
with the shield connected to the connector’s case/chassis may cause
malfunction and damage to the wiCICLE®orxture.
•wiCICLE®transmittershaveadditionalpowerrequirements
andthereforecannotbepowereddirectlyfromthexture.You
will need to utilize the supplied AC/DC adaptor to drive wiCI-
CLE®transmitters in your system.
WE HAD THIS SPACE, SO WE FIGURED WE’D DRAW
YOU A PICTURE:
Antenna Housing & 1/2-wave
Antenna
Antenna ferrule & articulation
joint
Stainless Steel Housing
Recessed Selector Button
Status LED
3-Pin XLR Connector
(Male on transmitter, Female
on receiver model)
Tabla de contenidos
Otros manuales de Equipo de iluminación de Blizzard Lighting
Blizzard Lighting
Blizzard Lighting Tournado SKY W-DMX Manual de usuario
Blizzard Lighting
Blizzard Lighting the puck pro zoom Manual de usuario
Blizzard Lighting
Blizzard Lighting KAYO.MORPH Manual de usuario
Blizzard Lighting
Blizzard Lighting ROCKER PANEL RGBAW Manual de usuario
Blizzard Lighting
Blizzard Lighting Lo-Pro CSI Manual de usuario
Blizzard Lighting
Blizzard Lighting Pocket Nebula Manual de usuario
Blizzard Lighting
Blizzard Lighting the puck Manual de usuario
Blizzard Lighting
Blizzard Lighting Northstar Spec-Z Manual de usuario
Blizzard Lighting
Blizzard Lighting Flurry TRI Manual de usuario
Blizzard Lighting
Blizzard Lighting Torrent Xray Manual de usuario
Blizzard Lighting
Blizzard Lighting The Puck 3NX Manual de usuario
Blizzard Lighting
Blizzard Lighting Kontrol 5 Manual de usuario
Blizzard Lighting
Blizzard Lighting Puck Pro Zoom EXA Manual de usuario
Blizzard Lighting
Blizzard Lighting COLORISE Infiniwhite Manual de usuario
Blizzard Lighting
Blizzard Lighting Torrent Streak Manual de usuario
Blizzard Lighting
Blizzard Lighting COLORISE Exa Manual de usuario
Blizzard Lighting
Blizzard Lighting Motif Sketch Manual de usuario
Blizzard Lighting
Blizzard Lighting the puck Manual de usuario
Blizzard Lighting
Blizzard Lighting REANIMATOR Manual de usuario
Blizzard Lighting
Blizzard Lighting RokBox Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
