Blizzard Lighting the puck pro zoom Manual de usuario
Blizzard Lighting, LLC
www.blizzardlighting.com
Waukesha, WI USA
Copyright (c) 2012
Page 2
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
TABLE OF CONTENTS
Puck Pro Zoom™ 1
1. Getting Started 3
What’s In The Box? 3
Getting It Out Of The Box 3
Powering Up! 3
Getting A Hold Of Us 3
Safety Instructions (Don’t Stick Your Hand In The Toaster!) 4
2. Meet The Puck Pro Zoom™ LED 5
Main Features 5
Optical Specs 5
Luminous Intensity Chart 5
The Puck Pro Zoom™ Pin-up Picture 6
3. Setup 7
Fuse Replacement 7
Connecting A Bunch Of Puck Pro Zoom™ PAR Cans 7
Data/DMX Cables 7
Cable Connectors 8
3-Pin??? 5-Pin??? Huh? 8
Take It To The Next Level: Setting up DMX Control 8
Fixture Linking (Master/Slave Mode) 9
Mounting/Rigging 9
4. Operating Adjustments 10
Navigating The Control Panel 10
Control Panel Menu Structure 11
DMX Mode 12
DMX Personalities 12
ID Address Selection 14
Temperature Control Functions 14
Edit Programs & Scenes 15
Advanced Setup Functions 15
Color Temperature-Based White Balance 16
Menu Key Protection 17
Static Color Display 17
Automatic Programs 17
Run Mode 17
Troubleshooting 18
5. Appendix 19
A Quick DMX Lesson 19
Keeping Your Puck Pro Zoom™ As Good As New 20
Returns (Gasp!) 20
Shipping Issues 20
Tech Specs 21
Page 3
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
1. GETTING STARTED
What’s In The Box?
• 1 x Puck Pro Zoom™ Professional LED PAR Fixture
• A totally rockin’ DMX Cable
• This Lovely User Manual
Getting It Out Of The Box
Congratulations on purchasing one of the coolest professional LED Par
xtures anywhere! Now that you’re the proud owner of a Puck Pro
Zoom™ (or hopefully, MORE!), you should carefully unpack the box
and check the contents to ensure that all parts are present and in good
condition. If anything looks as if it has been damaged in transit, notify
the shipper immediately and keep the packing material for inspection.
Again, please save the carton and all packing materials. If a xture must
be returned to the factory, it is important that the xture be returned in
the original factory box and packing.
Powering Up!
All xtures must be powered directly off a switched circuit and cannot
be run off a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel is used solely for a 0% to 100%
switch.
AC Voltage Switch - Not all xtures have a voltage select switch, so
please verify that the xture you receive is suitable for your local power
supply. See the label on the xture or refer to the xture’s specications
chart for more information. A xture’s listed current rating is its average
current draw under normal conditions. Check the xture or device
carefully to make sure that if a voltage selection switch exists that it is
set to the correct line voltage you will use.
Warning! Verify that the voltage select switch on your unit
matches the line voltage applied. Damage to your xture may
result if the line voltage applied does not match the voltage
indicated on the voltage selector switch. All xtures must be
connected to circuits with a suitable Ground (Earthing).
Getting A Hold Of Us
If something is wrong, just give us a call or send an email. We’ll
be happy to help, honest.
Blizzard Lighting
W220 N1531 Jericho Ct. Ste E
Waukesha, WI 53186 USA
www.blizzardlighting.com
414-395-8365
Email: [email protected]
Page 4
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
SAFETY INSTRUCTIONS
• Please keep this User Guide for future use. If you sell the unit to someone
else, be sure that they also receive this User Guide.
• ALWAYS make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the xture.
• This product is intended for indoor use only.
• To prevent risk of re or shock, do not expose xture to rain or moisture.
• Make sure there are no ammable materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least
20in (50cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
• ALWAYS disconnect from the power source before servicing or replacing fuse
and be sure to replace with same fuse size and type.
• ALWAYS secure xture using a safety chain. NEVER carry the xture by its
cord. Use its carrying handles.
• DO NOT operate at ambient temperatures higher than 104°F (40°C).
• In the event of a serious operating problem, stop using the unit immediately.
NEVER try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorized
technical assistance center. Always use the same type spare parts.
• NEVER connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Caution! There are no user serviceable parts inside the unit. Do not
open the housing or attempt any repairs yourself. In the unlikely event
your unit may require service, please contact Blizzard Lighting at
Page 5
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
2. MEET THE PUCK PRO ZOOM™ FLAT LED PAR
MAIN FEATURES:
• User selectable DMX personality modes
• Fixture ID address assignment and operation
• Built-in automated programs via master/slave
• User dened programs/scenes and upload feature
• Fixture temperature display and protection settings
• Preset or user adjustable white balance settings
• Menu key protection settings
• Easy to use LED digital control panel
• 3-pin male input and 3-pin female output
• Dual mounting yoke allows exibility in positioning
• Rugged extruded aluminum housing
OPTICAL:
• Motorized beam zooming 25°-45°
• Light Source: 14* 10-watt Quad-color LEDs, 100,000 hours
Luminous Intensity:
1m Narrow 1m Wide 2m Narrow 2m Wide
ALL 8600 Lux 3700 Lux 2900 Lux 1040 Lux
Red 2130 Lux 900 Lux 720 Lux 265 Lux
Green 2120 Lux 910 Lux 720 Lux 235 Lux
Blue 2200 Lux 1090 Lux 900 Lux 317 Lux
White 2200 Lux 1010 Lux 790 Lux 282 Lux
CONTROL:
• USITT DMX-512 (5/6/7/8/13 Channels)
• 3-pin Input/Output
• LED 4-button control panel
Page 6
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
Figure 1: Puck Pro Zoom™ Pin-Up Picture
Locking Knobs
Figure 2: The Rear Connections
LED Control
Panel Display
Dual Mounting Brackets
DMX Out
Control Panel
Buttons
Powercon
In
Powercon
Out
DMX In
Carrying
Handle/
Safety Point
Anodized Extruded
Aluminum Enclosure
High Power Quad-
Color LEDs
w/Zoomable Optics
Page 7
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
3. SETUP
Fuse Replacement
CAUTION! The Puck Pro Zoom™ utilizes a high-output switch-
mode power supply with an internal fuse. Under normal operating
conditions, the fuse should not require replacement. The fuse is eld
replaceable, however it is an advanced procedure suited to qualied
individuals. Should your Puck Pro Zoom™ fuse require replacement,
please contact Blizzard Lighting for instructions, or to return your unit
for service.
Connecting A Bunch of Puck Pro Zoom™ Fixtures
You will need a serial data link to run light shows using a DMX-512
controller or to run shows on two or more xtures set to sync in
master/slave operating mode. The combined number of channels
required by all the xtures on a serial data link determines the number
of xtures the data link can support.
Fixtures on a serial data link must be daisy chained in one single line.
Also, connecting more than 32 xtures on one serial data link without
the use of a DMX optically-isolated splitter may result in deterioration
of the digital DMX signal.
The maximum recommended cable-run distance is 500 meters (1640
ft). The maximum recommended number of xtures on a serial data
link is 32 xtures.
Data/DMX Cabling
To link xtures together you’ll need data cables. You should use data-
grade cables that can carry a high quality signal and are less prone to
electromagnetic interference.
For instance, Belden© 9841 meets the specications for EIA RS-
485 applications. Standard microphone cables will “probably” be
OK, but note that they cannot transmit DMX data as reliably over
long distances. In any event, the cable should have the following
characteristics:
2-conductor twisted pair plus a shield
Maximum capacitance between conductors – 30 pF/ft.
Maximum capacitance between conductor & shield – 55 pF/ft.
Maximum resistance of 20 ohms / 1000 ft.
Nominal impedance 100 – 140 ohms
Page 8
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
Cable Connectors
Cables must have a male XLR connector on one end and a female XLR
connector on the other end. (Duh!)
CAUTION: Do not allow contact between the common and the
xture’s chassis ground. Grounding the common can cause a ground
loop, and your xture may perform erratically. Test cables with an
ohm meter to verify correct polarity and to make sure the pins are not
grounded or shorted to the shield or each other.
3-Pin??? 5-Pin??? Huh?!?
If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter.
They are widely available over the internet and from specialty retailers. If you’d like to build your own,
the chart below details a proper cable conversion:
Conductor 3-Pin Female
(Output)
5-Pin Male
(Input)
Ground/Shield Pin 1 Pin 1
DMX Data (-) Pin 2 Pin 2
DMX Data (+) Pin 3 Pin 3
Not Used. No Connection. No Connection.
Not Used. No Connection. No Connection.
Take It To The Next Level: Setting Up DMX Control
Step 1: Connect the male connector of the
DMX cable to the female connector (output)
on the controller.
Step 2: Connect the female connector of
the DMX cable to the rst xture’s male
connector (input). Note: It doesn’t matter
which xture address is the rst one
connected. We recommend connecting the
xtures in terms of their proximity to the
controller, rather than connecting the lowest
xture number rst, and so on.
Step 3: Connect other xtures in the chain
from output to input as above. Place a DMX
terminator on the output of the nal xture
to ensure best communication.
Page 9
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the
DMX cable to the output (female) 3 pin connector of
the rst xture.
2. Connect the end of the cable coming from
the rst xture which will have a (female) 3 pin
connector to the input connector of the next xture
consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above
to the input of the following xture and so on.
A quick note: Often,
the setup for Master-
Slave and Standalone
operation requires that
the rst xture in the
chain be initialized for
this purpose via either
settings in the control
panel or DIP-switches.
Secondarily, the xtures
that follow may also
require a slave setting.
Check the “Operating Adjustments” section in this manual for
complete instructions for this type of setup and conguration.
Mounting & Rigging
This xture may be mounted in any SAFE position provided there is
enough room for ventilation.
It is important never to obstruct the fan or vents pathway. Mount the
xture using a suitable “C” or “O” type clamp. The clamp should be
rated to hold at least 10x the xture’s weight to ensure structural
stability. Do not mount to surfaces with unknown strength, and ensure
properly “rated” rigging is used when mounting xtures overhead.
Adjust the angle of the xture by loosening both knobs and tilting the
xture. After nding the desired position, retighten both knobs.
• When selecting installation location, take into consideration lamp
replacement access (if applicable) and routine maintenance.
• Safety cables MUST ALWAYS be used.
• Never mount in places where the xture will be exposed to rain,
high humidity, extreme temperature changes or restricted ventilation.
Page 10
The Puck Pro Zoom Manual Rev. A Copyright (c) 2012 Blizzard Lighting, LLC
4. OPERATING ADJUSTMENTS
The Control Panel
All the goodies and different modes possible with the Puck Pro Zoom™
are accessed by using the control panel on the rear of the xture.
There are 4 control buttons below the LED display which allow you to
navigate through the various control panel menus.
<MENU>
Is used to navigate to the previous higher-level menu item.
<UP>
Scrolls through menu items and numbers in ascending order.
<DOWN>
Scrolls through menu items and numbers in descending order.
<ENTER>
Is used to select and conrm/store the current selection.
The Control Panel LED Display shows the menu items you select from
the menu map on page #11. When a menu function is selected, the
display will show immediately the rst available option for the selected
menu function. To select a menu item, press <ENTER>.
Press the <MENU> button repeatedly until you reach the desired
menu function. Use the <UP> and <DOWN> buttons to navigate the
menu options. Press the <ENTER> button to select the menu function
currently displayed, or to enable a menu option. To return to the
previous option or menu without changing the value, press the
<MENU> button.
Tabla de contenidos
Otros manuales de Equipo de iluminación de Blizzard Lighting
Blizzard Lighting
Blizzard Lighting Torrent Xray Manual de usuario
Blizzard Lighting
Blizzard Lighting PixelStorm COB Mini Manual de usuario
Blizzard Lighting
Blizzard Lighting HUSH PAR Infiniwhite 500 Manual de usuario
Blizzard Lighting
Blizzard Lighting Tour QT Skywire Manual de usuario
Blizzard Lighting
Blizzard Lighting HotBox RGBW/RGBA Manual de usuario
Blizzard Lighting
Blizzard Lighting Puck CSI Xtreme Manual de usuario
Blizzard Lighting
Blizzard Lighting ToughPar V12 Manual de usuario
Blizzard Lighting
Blizzard Lighting Northstar Spec-Z Manual de usuario
Blizzard Lighting
Blizzard Lighting Flurry TRI Manual de usuario
Blizzard Lighting
Blizzard Lighting Flurry EXA Manual de usuario
Blizzard Lighting
Blizzard Lighting Pocket Rocket Manual de usuario
Blizzard Lighting
Blizzard Lighting snokontrol Manual de usuario
Blizzard Lighting
Blizzard Lighting Torrent F3 Manual de usuario
Blizzard Lighting
Blizzard Lighting REANIMATOR Manual de usuario
Blizzard Lighting
Blizzard Lighting Rocklite RGBAW Manual de usuario
Blizzard Lighting
Blizzard Lighting the puck Manual de usuario
Blizzard Lighting
Blizzard Lighting The Puck RGB Unplugged Manual de usuario
Blizzard Lighting
Blizzard Lighting Mezmerizor 4FX Manual de usuario
Blizzard Lighting
Blizzard Lighting Node:b RGBAL Manual de usuario
Blizzard Lighting
Blizzard Lighting Motif Risplendi 150 Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
