Blendtec HP3A Home Manual de usuario

Model HP3A

Instruction Manual

www.coolshinystuff.com

Table of Contents

SECTION PAGE #

SECTION 1: IMPORTANT SAFEGUARDS 1

SECTION 2: UNPACKING 3

SECTION 3: BLENDER OVERVIEW 4

SECTION 4: INSTALLATION 4

SECTION 5: CARE AND CLEANING 6

SECTION 6: OPERATIONAL OVERVIEW 7

SECTION 7: TROUBLESHOOTING 8

SECTION 8: WARRANTY 10

HP-1

SECTION 1

IMPORTANT INFORMATION

Read all instructions carefully before using your Blender™

1.1 SAFETY CERTIFICATION

The blender is certied by ETL (Report No. 3018204-4,

3018204-2 & 3018204-3).

1.2 CERTIFICATION

Blender and its accessories are certied by NSF

International (NSF), under K-TEC in the NSF Ofcial

Listing.

1.3 AVOID CONTACT WITH MOVING PARTS

• Keep ngers, hands, hair and clothing away from all moving parts.

• Keep all utensils away from the drive socket and blender blades during

operation. Metal utensils will damage blades.

• NEVER put hands into blender jar or add substances by hand when the

blender is operating.

• NEVER place jar into drive socket if blender motor is operating.

• DO NOT rock the blender during operation.

These precautions will prevent personal injury and/or damage to the blender.

1.4 NEVER OPERATE THE BLENDER IF IT APPEARS DAMAGED

If the blender malfunctions call your service agent rst. If it is dropped or dam-

aged in any way, return the blender to a Blendtec service agent immediately for

examination, repair, electrical or mechanical adjustment, or possible replace-

ment.

1.5 NEVER OPERATE BLENDER IN LIQUID

Do not operate the blender motor in water or any other liquid. Avoid all contact

between the motor and water. Do not use the blender outdoors where it is sub-

ject to precipitation.

1.6 NEVER PUT NON-FOOD ITEMS INTO JAR

Metal utensils, rocks and glass are dangerous if placed in jar. Damage caused

by such foreign objects will void the warranty. Keep hands and utensils out of

jar while blending to reduce the risk of severe injury to persons or damage to the

blender. Utensils may only be used when the blender is not running.

1.7 NEVER OPERATE THE BLENDER WITHOUT THE LID IN PLACE

HP-2

1.8 NEVER OPERATE THE BLENDER USING ATTACHMENTS NOT SOLD

BY BLENDTEC

The use of any unauthorized attachments may cause re, electric shock, and/or

injury and will void the warranty.

1.9 CONTAINER MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS

OPERATING

1.10 BLADES ARE SHARP! HANDLE CAREFULLY!

1.11 WHEN BLENDING HOT LIQUIDS, REMOVE CENTER PIECE OF LID

1.12 POWER CORD PRECAUTIONS

• NEVER operate with a damaged cord or plug. (If the supply cord is damaged

it must be replaced by the manufacturer, or authorized service agent to avoid

a hazard

• DO NOT permit the cord to hang over the edge of the work surface.

• NEVER use an extension cord with the unit.

• Unplug the blender motor when not in use; before changing blender loca-

tions; or cleaning.

1.13 NEVER ATTEMPT TO REPAIR THE POWER UNIT

Never remove the blender motor cover. The blender motor does not contain self-

adjustable or serviceable parts. A qualied service agent must make all service

adjustments. Removing the cover or attempting to service the blender will void

the warranty.

1.14 TURN THE POWER SWITCH OFF WHEN NOT IN USE

The Power Switch (ON/OFF switch) is located on the back of the blender motor

cover.

1.15 AVOID TOUCHING THE BLENDER DRIVE SOCKET AFTER EXTENSIVE

USE.

The blender drive socket may become hot after numerous cycles.

1.16 CLOSE SUPERVISION IS NECESSARY WHEN APPLIANCE IS USED BY

OR NEAR CHILDREN.

1.17 THE BLENDER IS INTENDED FOR HOME USE ONLY! ANY USE OF THE

BLENDER FOR COMMERCIAL PURPOSES VOIDS ALL WARRANTIES.

SAVE THESE INSTRUCTIONS

HP-3

SECTION 2

SAVE ALL PACKAGING MATERIALS AND INSTRUCTIONS FOR FUTURE

USE.

2.1 UNPACKING YOUR BLENDER

You should have received the following items:

• Motor base

• Blender jar with lid

• Recipe book

1. Remove blender motor, blender jar and lid from packaging.

2. Unwind the power cord.

3. Check for any packing material that may have blocked ventilation holes in

the blender motor.

4. Inspect all items to ensure no damage occurred in shipment.

5. If any damage has occurred contact your Blendtec service agent

immediately.

2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE

Record your blender motor serial number and date of purchase in the space

below. You will need these when contacting Blendtec for service or questions.

Motor Serial #:

____________________________________________________

(Found on bottom of motor base)

Date of Purchase:

____________________________________________________

Purchased From

____________________________________________________

2.3 REGISTRATION OF YOUR BLENDER

under the Support button) or return the registration card to the address provided.

HP-4

SECTION 3

Blender OVERVIEW

(Refer to Figures 1 and 2)

3.1 BLENDER MOTOR

• Motor Cover: Houses the power unit in a durable, easy-to-clean

polycarbonate.

• Touch Pad: Consists of six buttons that contain pre-programmed settings for

selective blender control, a pulse button, and two speed control buttons.

• LCD Information Center: will indicate status of unit as well as overload or

over-temperature conditions.

• Power Unit: This unit is located within the blender motor and contains the

machinery that runs the blender.

• Power Switch: Located on the back lower-right corner of the power unit.

3.2 BLENDER JAR ASSEMBLY

The blender jar assembly consists of the blender jar, blade assembly, and lid.

• Jar: Made from polycarbonate to provide maximum efciency and clear

visibility of blender performance.

• Blade Assembly: Stainless steel designed to provide fast consistent blending

SECTION 4

INSTALLATION

We recommend that surge protection be placed between the receptacle and the

blender motor.

1. Place blender on a at, clean and dry surface.

2. Make sure a plug outlet is available within four feet of the blender motor.

3. Ensure that the unit is turned off before plugging it into a separate 120-volt

receptacle.

4. Ensure that blender vents are unobstructed to allow proper cooling during

use.

HP-5

HP-6

SECTION 5

CARE AND CLEANING

5.1 AFTER USE CLEANING

1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender

jar.

2. Place the lid tightly onto the jar. Place the blender jar on the blender base,

and with your hand placed on top of the lid; press the pulse button for 5

seconds.

3. Rinse with clear water until all soap is rinsed from jar and lid.

4. Clean the blender base by simply wiping the base and touchpad with a

damp rag and water.

5.2 LONG-TERM SANITATION

1. For long-term sanitation, occasionally ll the blender jar half way with hot

water.

2. Add one teaspoon of liquid chlorine bleach.

3. Stir for 10 seconds to mix water and bleach. Let mixture stand in blender jar

for ve minutes.

4. Empty water/bleach mixture and rinse the jar thoroughly to ensure that there

is no bleach mixture left in the jar. Turn jar RIGHT SIDE UP on dish rack

until dry.

5.3 CLEANING TIPS AND CAUTIONS

• Do not use abrasives or stiff brushes to clean the blender base or jar as this

will dull or scratch the surface. Cosmetic damage is not covered by war-

ranty.

• NEVER submerge the blender motor in water. Avoid submerging blender jars

for more than 5 minutes. Water penetration through the lower jar seals will

reduce the life of the jar. After cleaning, we recommend the blender jar be

stored upright.

• BLENDER JAR IS DISHWASHER SAFE - TOP RACK ONLY! Extreme tem-

peratures damage the lower seal to the jar.

HP-7

SECTION 6

OPERATIONAL OVERVIEW

Your Blendtec home blender has 30+ pre-programmed blend cycles for your con-

venience, or optional manual controls. A representation of the controls is found

below:

6.1 BEFORE YOU BEGIN OPERATION

1. Turn on the main power switch located on the back of the blender motor in

the lower right corner. The display on the front will read “Blendtec home”

2. Place the blender jar on the base, making sure the jar is secure. Attach the

blender lid.

6.2 MANUAL CONTROLS

START/STOP: The START/STOP button can be pressed at any time to stop the

current blender function.

PULSE: To use the high speed pulse, simply hold hold the pulse button for the

desired amount of time. The blender will stop when you release the button. The

Pulse function can also be activation during a blend cycle. When the pulse but-

ton is pressed the current cycle pauses and the pulse begins. When the pulse

button is released the selected cycle resumes.

SPEED UP/SPEED DOWN: Pressing the UP button will start a speed cycle for

50 seconds. During this time press or hold down the UP/DOWN arrows to con-

trol up to 9 speeds at which the blender can operate

START

STOP

PULSE

EXITEXITPRESETS SPEED/OPTIONS

SELECT

CYCLE

MODE

3 4

Otros manuales para HP3A Home

Tabla de contenidos

Otros manuales de Licuadora de Blendtec

Blendtec

Blendtec ez Blender Manual de usuario

Blendtec

Blendtec CLASSIC SERIES Wildside+ Guía

Blendtec

Blendtec CLASSIC SERIES Guía

Blendtec

Blendtec A3-31E-BHMV Manual de usuario

Blendtec

Blendtec CLASSIC SERIES Guía

Blendtec

Blendtec DESIGNER SERIES Guía

Blendtec

Blendtec Go 41-503 Manual de usuario

Blendtec

Blendtec Total Blender Guía

Blendtec

Blendtec Designer Series WildSide Manual de usuario

Blendtec

Blendtec Xpress Manual de usuario

Blendtec

Blendtec Wildside Plus Designer Series Guía

Blendtec

Blendtec CLASSIC SERIES Guía

Blendtec

Blendtec Xpress Blender Manual de usuario

Blendtec

Blendtec Professional Series Manual de usuario

Blendtec

Blendtec Home Blender Guía

Blendtec

Blendtec Mix n Blend II Guía rápida

Blendtec

Blendtec CHEF Manual de usuario

Blendtec

Blendtec Total Blender Classic Combo Manual de usuario

Blendtec

Blendtec DESIGNER SERIES Guía

Blendtec

Blendtec Classic Manual de usuario

Blendtec

Blendtec DESIGNER SERIES Guía

Blendtec

Blendtec 625D Manual de usuario

Blendtec

Blendtec DESIGNER 625 Manual de usuario

Blendtec

Blendtec Brawn Manual de usuario

Manuales populares de Licuadora de otras marcas

ROTOR

ROTOR 1125.201 Manual de usuario

Braun

Braun Multiquick 5 Vario series Manual de usuario

ARENDO

ARENDO MIRA 305424 Manual de usuario

CHEF-BUILT

CHEF-BUILT CCB-3500 Manual de usuario

Viconte

Viconte VC-4406 Manual de usuario

Oster

Oster BLSTAB-CB0 Manual de usuario

HOFFEN

HOFFEN MC-3005 Manual de usuario

Black & Decker

Black & Decker BLC18750DM Manual de usuario

Sunbeam

Sunbeam 4182 Manual de usuario

Bialetti

Bialetti FMX35 Manual de usuario

Black & Decker

Black & Decker BL8000 Manual de usuario

Duronic

Duronic BL530 Manual de usuario

Exquisit

Exquisit MS 3002 wes Manual de usuario

Lumme

Lumme LU-KP1891A Manual de usuario

Binatone

Binatone HB-735 Manual de usuario

Moulinex

Moulinex LM936E10 Manual de usuario

Oster

Oster VERSA Manual de instalación y operación

Ninja

Ninja NN210Q Manual de usuario