Black Box IC147A-R3 Manual de usuario
BL A C K B O X®
Connect four or seven standard (1.5-Mbps)
or high-speed (480-Mbps) USB devices to your
computer.
USB 2.0 High-Speed Hub
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,
PA 15055-1018 • Web site: www.blackbox.com • E-mail: [email protected]
Customer
Support
Information
IC147A- R3
IC148A
1. Specifications
Distance (Maximum): 15 ft. (4.5 m)
Speed: 1.5/12/480 Mbps
RoHS: Yes
Connectors: IC147A-R3: (4) USB Type A F, (1) USB mini Type B F;
IC148A: (7) USB Type A F, (1) USB mini Type B F
Power: From the USB interface or from external power supply;
From external power supply: Input: 120 VAC, 0.4 amps, 47–63 Hz;
Output: 5 VDC, 2 amps
Size: IC147A-R3: 0.5"H x 1.4"W x 3.3"D (1.3 x 3.6 x 8.4 cm);
IC148A: 0.6"H x 4.5"W x 2.4"D (1.5 x 11.4 x 6.1 cm)
Page 2 724-746-5500 | blackbox.com
USB 2.0 High-Speed Hub
2. Overview
2.1 Introduction
The USB 2.0 High-Speed Hub is USB 2.0 compliant and connects to a Universal
Serial Bus (USB) port on your desktop or notebook computer. This slim hub has 4
or 7 ports for connecting USB (high-speed 480 Mbps or standard 1.5 Mbps)
devices to your computer. With a maximum bandwidth of 480 Mbps, this slim
hub enables you to connect devices that consume a large amount of bandwidth,
such as an external storage device, printer, scanner, DVD or CD-RW drive or digital
camera, to your computer.
2.2 Features
• Complies with Universal Serial Bus Specification Version 2.0 (Data Rate
1.5/12/480 Mbps)
• Four or seven external USB Type A downstream ports
• Connects up to a maximum of 127 USB devices through cascading multiple
hubs
• Derives power from the USB interface or from provided power supply
• Enables one Transaction Translator per hub and supports four or seven
concurrent non-periodic transactions
• Supports plug-and-play and hot-swap functions
• Compatible with Windows® and Mac® OS
• Supports EHCI/UHCI/OHCI specification
• Per-port output voltage is +5 VDC. Output current is 500 mA
2.3 System Requirements
To use the hub, your computer must meet the following hardware requirements
and run on one of the operating systems listed in Section 2.4.
NOTE: The USB 2.0 High-Speed 4- and 7-Port Hubs are backward compatible, so
you can connect them to a computer with either a USB 1.1 or 2.0 interface.
When using the hub with a computer that has a version 1.1 USB interface,
all the devices attached to the hub will run at USB 1.1 speed (up to
12 Mbps).
2.4 Hardware Operating System
• 64 MB RAM or higher, depending on the operating system
• USB interface
Page 3
724-746-5500 | blackbox.com
USB 2.0 High-Speed Hub
• Windows 98 SE/Windows Me/Windows 2000/Windows XP/Windows Vista®/
Windows 7 and higher
• Mac OS 8.6 and higher
3. Installation
3.1 Connecting the Hub and Installing the Driver
To connect the hub to your computer and install the operating system’s default
driver, follow the steps listed below.
The hub comes with one high-speed Type A/mini USB cable so that you can
connect it to a host computer.
1. Power on the computer.
2. Plug the supplied cable’s USB Type A connector end into a USB port on your
computer.
3. Plug the cable’s USB mini USB connector end into the hub.
4. Your computer’s operating system automatically detects the new hardware and
begins installing the appropriate default driver. If the power LED does not come
on, attach the AC power adapter to the AC power jack on the hub and plug
the adapter into an electrical outlet.
5. Follow the on-screen instructions to complete the driver installation. You can
now connect USB devices to the hub or daisychain additional hubs.
3.2 Connecting Devices to the USB Hub
To connect a USB device, plug it into a USB port on the hub and follow any
additional instructions provided with the device. When connecting new devices
to the hub, consider the following guidelines.
• If your computer is running the Windows 98 operating system, a series
of screens appears, beginning with the “Add New Hardware Wizard,” to guide
you through the driver installation process.
• If your computer is running Windows 98 SE, Windows Me, Windows 2000,
Windows XP, Windows Vista, or Windows 7, the device driver may install
automatically.
• When connecting a new device to your hub, you must run the “Setup” or
“Install” program for that device.
• When connecting a device to the hub, to avoid possible damage, never force
the cable connector into the port on the hub if the cable connector does not
attach.
FREE, live, 24/7 Tech Support is just 30 seconds away.
724-746-5500 | blackbox.com
3.3 Device Not Working
• Make sure that the device is connected to the hub.
• Plug the device into a different port on the hub. If it still does not work, test the
device by connecting it directly to your computer.
• Check that you ran the “Setup” or “Install” program for the device.
• Make sure that the device appears in Device Manager. See Section 3.4.
• Disconnect all devices from the hub and reconnect them, one at a time. Check
that each device works before plugging in the next device.
3.4 Verifying Device is Installed in Windows Operating System
To check that the hub is installed properly, use Device Manager to locate the
Generic USB Hub on USB 2.0 Bus device. To access Device Manager for Windows
98/Me operating system, right-click “My Computer, Properties” and then click the
“Device Manager” tab. For Windows 2000/XP/7 and Windows Vista, right-click
“My Computer, Properties, Hardware tab,” then click the “Device Manager” tab.
To test that the hub is working properly, in the Device Manager window:
• Select the “Generic USB Hub” on USB 2.0 Bus device.
• Click the “Properties” button or icon, depending on the operating system.
• Verify that the message “This device is working properly” appears.
• To verify that the Hub is installed properly for Mac, locate the “Generic USB Hub
on USB 2.0 Bus device” by opening “Apple System Profiler” and clicking
“Devices and Volumes.”
IC147A-R3, rev. 1
© Copyright 2010. Black Box Corporation. All rights reserved. Printed in U.S.A.
Black Box® and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Double Diamond™ is a
trademark of BB Technologies, Inc.
Mac is a registered trademark of Apple Computer, Inc.
Windows and Windows Vista are registered trademarks of Microsoft Corporation.
Any other third-party trademarks appearing in this publication are acknowledged to be the property of their respective
owners.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de Black Box
Black Box
Black Box SW980A Manual de usuario
Black Box
Black Box LPB2848A Manual de usuario
Black Box
Black Box SWL065A Manual de usuario
Black Box
Black Box ACU7017A Manual de usuario
Black Box
Black Box ServSwitch SW721A-R5 Manual de usuario
Black Box
Black Box SERVSWITCH Series Manual de usuario
Black Box
Black Box LBG1000A-R2 Manual de usuario
Black Box
Black Box LGB1005A-R2 Manual de usuario
Black Box
Black Box IC562A Manual de usuario
Black Box
Black Box LPB1308A Manual de usuario
Black Box
Black Box KV162A Manual de usuario
Black Box
Black Box ServSwitch Manual de usuario
Black Box
Black Box ServSensor JR EME102A Manual de usuario
Black Box
Black Box LH8112A Manual de usuario
Black Box
Black Box SW722A-R2 Manual de usuario
Black Box
Black Box SW1042A-MM Manual de usuario
Black Box
Black Box LGH1000 Series Manual de usuario
Black Box
Black Box SW614A Manual de usuario
Black Box
Black Box LGB4308A Manual de usuario
Black Box
Black Box ServSwitch Summit KV1500A Manual de usuario
