Black Box JPM440A Manual de usuario

1000 Park Drive • Lawrence, PA 15055-1018 • 724-746-5500 • Fax 724-746-0746

Installation

Use the splice tray with single-mode or multimode fiber cable. Follow the instructions below.

SINGLE-MODE SPLICING

1. Remove the top metal splice tray cover and install the bottom metal splice cover in the wallmount or

rackmount fiber cabinet.

2. Remove the single-mode plastic covers on each of the four single-mode plastic bases already installed in

the bottom metal splice cover.

3. Remove the yellow sticker from one of the single-mode plastic bases.

4. Install a metal sleeve and slide the single-mode fiber through it that you plan to splice. (For single-mode

fiber, you’ll use fusion splicing.)

5. Prepare and splice the fiber.

6. After splicing is complete, snap the spliced fiber in one of the 6 compartment areas in the plastic base.

7. Repeat until all 6 compartments are filled.

8. Re-install the single-mode plastic cover.

9. Repeat steps 2 through 8 for the remaining three single-mode plastic bases as required by your

application.

10. When all single-mode plastic bases are loaded with fiber, use the cable ties to secure the cable. Then

re-install the top metal splice tray cover and tighten the wing nuts (included with the cabinet).

MULTIMODE SPLICING

1. Remove the top metal splice tray cover and install the bottom metal splice cover in the wallmount or

rackmount fiber cabinet.

2. Remove the single-mode plastic covers on each of the four single-mode plastic bases already installed.

3. Remove the larger single-mode plastic bases and install the smaller multimode plastic bases in the bottom

metal splice cover. (The multimode plastic base supports the Corning Cable Systems Non-Adhesive

Mechanical Splice, Corning part number 95-000-04 or Black Box part number FO030.)

4. Splice the multimode fiber. (For multimode fiber, you’ll use mechanical splicing.)

5. After the mechanical splice is done, install the mechanical splice in one of the 6 compartments in the

multimode plastic base.

6. Repeat until all 6 compartments are filled.

7. Re-install the multimode plastic cover.

8. When all multimode plastic bases are loaded with fiber, use the cable ties to secure the cable. Then

re-install the top metal splice cover and tighten the wing nuts (included with the cabinet) to secure the

cable.

TRADEMARKS USED IN THIS MANUAL

Any trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746

Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018

Web site: www.blackbox.com • E-mail: [email protected]

CUSTOMER

SUPPORT

INFORMATION

JUNE 2004

JPM440A

Splice Tray

Specifications

Size: 0.5"H x 9.4"W x 5.5"D (1.3 x 23.8 x 14 cm)

Weight: 0.8 lb. (0.4 kg)

Overview

The Splice Tray can splice up to 24 strands of single-mode or multimode fiber. It’s used with the Wallmount

Fiber Cabinets [JPM401A-R2–402A-R2] and the Rackmount Fiber Cabinets [JPM406A-R2–407A-R2 and

JPM418A-R2].

What’s Included

Your package should include the following items. If anything is missing or damaged, please contact Black Box

at 724-746-5500.

• (1) top metal splice cover

• (1) bottom metal splice cover

• (25) metal sleeves for single-mode splicing

• (4) single-mode plastic covers and bases (already installed in the bottom splice cover)

• (4) multimode plastic covers and bases

• (30) 3" (7.6-cm) cable ties

• (4) yellow stickers attached to the single-mode plastic bases

Bottom metal

splice cover

Yellow sticker

Single-mode plastic

base

Tabla de contenidos

Otros manuales de Hardware de red de Black Box

Black Box

Black Box JPM083A Manual de usuario

Black Box

Black Box SW543A Manual de usuario

Black Box

Black Box MT330A Manual de usuario

Black Box

Black Box Veri-NAC LVN5600A Manual de usuario

Black Box

Black Box LB0010A-A24-R2 Manual de usuario

Black Box

Black Box 5000 series Manual de usuario

Black Box

Black Box DT450A Manual de usuario

Black Box

Black Box MX550A Manual de usuario

Black Box

Black Box FOM Line Driver-ST Manual de usuario

Black Box

Black Box Multi Quick Check RJ-11 Manual de usuario

Black Box

Black Box Secure Site Manager 8 Manual de usuario

Black Box

Black Box EXPANDABLE CABLE MANAGEMENT RACK RM1400A Manual de usuario

Black Box

Black Box AC1060A Manual de usuario

Black Box

Black Box RADIAN 1000 Series Manual de usuario

Black Box

Black Box LB9218A Manual de usuario

Black Box

Black Box MC144A Manual de usuario

Black Box

Black Box AC431A Manual de usuario

Black Box

Black Box Lineshare Pro AC FX150A Manual de usuario

Black Box

Black Box JPM403A-R2 Manual de usuario

Black Box

Black Box AC1003A Manual de usuario

Black Box

Black Box USB Director RS-232 Manual de usuario

Black Box

Black Box Veri-NAC Manual

Black Box

Black Box TL601A-R2 Manual de usuario

Black Box

Black Box ACR2004A Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario