Bkav AI View P400 Manual de usuario
4k dome
AI-BASED CAMERA
Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.
Model: P400
Product number: 0803F/0802N/0803FW/0802NW
INSTALLATION GUIDE
PRODUCT KIT
Drilling position decalInstallation guide
Camera
3
WALL DECAL FOR
DRILLING POSITION
Ø10 mm, 3 holes
Thank you letter
Wi-Fi antenna
(0803FW/0802NW)
Hex tool
size 3, 4, 5
Set 3 of screws
and anchors
GPS antenna
(Option)
Waterproof
couplings
4k dome
AI-BASED CAMERA
Qualcomm products contained herein are products of Qualcomm Technologies, Inc. and/or its subsidiaries.
Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries.
The Made with Qualcomm Technologies logo is a trademark of Qualcomm Incorporated.
TECHNICAL SPECIFICATION
Protection standards IP66, IK10
4
Resolution, frame rate UHD 3840 x 2160, 60fps
Optical zoom
Dimentions (L x W x H)
Weight
P400-0803F / P400-0803FW: 3x
P400-0802N / P400-0802NW: 2x
Focal length
P400-0803F / P400-0803FW: 10.9 - 29mm ± 5%
P400-0802N / P400-0802NW: 4.36 - 9.33mm ± 5%
L296.5 x W165 x H266.5mm
3.5kg
Field of view (horizontal - vertical)
P400-0803F / P400-0803FW: Near: 42° - 22.8° / Far: 15° - 8.4°
P400-0802N / P400-0802NW: Near: 111.96° - 58.11° / Far: 47.23° - 26.53°
Environment conditions
-40°C - 50°C (-40°F - 122°F)
Humidity 10 - 100%
Power supply
POE IEEE802.3af/802.3at
Maximum 13W, 12VDC
PRODUCT OVERVIEW
12VDC power supply
RJ45 terminal block
Camera body
Camera lens
Dust and waterproof lens protector
Infrared LED
5
INSTALLTION GUIDE
Step 1: Apply to the position decal and then drill 4 anchors to the wall (Figure 1).
Step 2: Fix the camera mount with 3 anchors onto the wall (Figure 2).
Step 3: Tighten 3 screws to fix the camera onto the wall.
1 2
6
Drilling position decal
1 2
7
Connecting GPS antenna:
Step 1: Insert the GPS antenna connector into the waiting cable terminal (Figure 1).
Step 2: Put the GPS antenna on the position, as in the figure and fix it using silicone glue.
Connecting Wi-Fi antenna (with Wi-Fi assistant model)
Insert 2 Wi-Fi antennas into 2 available terminal positions (Figure 2).
WI-FI, GPS ANTENNA INSTALLATION
GPS antenna
Wi-Fi antenna
CONNECTING DEVICES INSTALLATION
8
LAN
12VDC/1A
Two options to connect devices:
Option 1: Use the network cable connected from the switch PoE to the waiting RJ45 terminal, no need
to use 12VDC power supply (Figure 1).
Option 2: Use 12VDC power supply and the network cable connected from the switch (Figure 2).
2
RJ45
Switch PoE
1
RJ45
Connect the PoE cable. Insert the cable into the
waterproof coupling before connecting the wires
into the terminal.
360°
ADJUSTING THE CAMERA VIEWING ANGLE
65°
9
10
THE MEMORY CARD AND RESET INSTALLATION
Power off the camera, press and hold the factory reset button. Continue to hold the factory reset button
for another 10 seconds while powering the camera, the camera will be restored to factory settings.
Note:
Reset installation: Open the protective cover that protects the camera against dust and water to reset the device.
Memory card: Open the protective cover, you can find the location of Micro SD card.
Mirco SD card
Reset factory
Este manual sirve para los siguientes modelos
4
Tabla de contenidos
Otros manuales de Cámara de seguridad de Bkav
Bkav
Bkav AI VIEW P450 Manual de usuario
Bkav
Bkav AI VIEW C300-0200 Manual de usuario
Bkav
Bkav AI View S500-0233 Manual de usuario
Bkav
Bkav AI View P450-0802GN Manual de usuario
Bkav
Bkav AIView S201 Manual de usuario
Bkav
Bkav AI VIEW C300-0200 Manual de usuario
Bkav
Bkav AI VIEW S500 Manual de usuario
Bkav
Bkav AI VIEW C100-0200 Manual de usuario
Bkav
Bkav AI VIEW ULTRA ZOOM BULLET S200 Manual de usuario
Bkav
Bkav AI View S200-0233 Manual de usuario
