Bigassfans K3150-A2 Manual de usuario
INSTALLATION GUIDE
INSTALLATION GUIDE
GUÍA DE INSTALACIÓN
GUIDE D’INSTALLATION
READ AND SAVE THESE INSTRUCTIONS
Topic Page
Technical Specifications 3
Tools Needed 3
Parts and Hardware
Low Profile Mount 4
Standard Mount 5
Universal Mount 6
Prepare the Fan Site 7
Install Your Fan
Airfoils 8
Lower Cover and Trim 10
Mounting Bracket 12
Mounting: Low Profile 22
Mounting: Standard 30
Mounting: Universal 42
Test Your Fan 54
Models: K3150-A2, K3150-S0, K3150-X2
Installation Guide
For operation, maintenance, and
troubleshooting information, visit
bigassfans.com/support
3
HAIKU®BY BIG ASS FANS
Disconnect power to the fan location! Do not use the fan with a dimmer switch!
A licensed electrician must install the fan if required by your local electrical code.
The ground wire must be connected to the supply ground and its length must be longer than the
safety cable!
Technical Specifications
Diameter Weight Operating voltage Operating frequency
132 cm ≤6.4 kg 100–240 VAC, 1 Φ50–60 Hz
152 cm ≤7.3 kg 100–240 VAC, 1 Φ50–60 Hz
213 cm ≤11.3 kg 100–240 VAC, 1 Φ50–60 Hz
Tools Needed
• Ladder
• Wire Strippers
• Phillips Screwdriver
• Wrenches
Box Contents
As you remove the fan from its packaging, make sure you are not missing any components required for
assembly and operation. If you ordered multiple fans, be sure to keep the components of each fan together!
!
!
!
4REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
PARTS & HARDWARE: LOW PROFILE MOUNT
Use the two screw caps that match the color of your fan.
Safety cable not shown.
†
††
Mounting plate
(2) Rubber bumper
(2) Mounting bracket
Lower cover
Lower cover trim
(3) Airfoil
Motor hub
(2) Extension tube screw cap†
Remote control
Mounting hardware
• (4) 6 mm Nylock nut
• Safety cable shackle††
Airfoil hardware
• (6) M5 airfoil screw
• (6) 5 mm lock washer
Wiring hardware
• Wire connectors
• Wire nut
• (2) Wiring cover screw
a
b
g
d
j
e
f
k
c
h
a
b
c
d
e
f
g
h
i
j
k
l
i
l
5
HAIKU®BY BIG ASS FANS
PARTS & HARDWARE: STANDARD MOUNT
Rubber bushing
Mounting bracket†
(2) Mounting brace bracket
Wiring cover
Wiring cover trim
Lower cover
Lower cover trim
(3) Airfoil
Motor hub
Remote control
Mounting hardware
• (2) M6 x 1 x 25 mm socket cap screw††
• (2) M6 x 1 nylock nut††
• M8 Bolt
• 8 mm flat washer
• 8 mm lock washer
• M8 nut
• 2 mm x 2 mm split pin
• Safety cable shackle†††
Airfoil hardware
• (6) M5 airfoil screw
• (6) 5 mm lock washer
Wiring hardware
• Wire connectors
• Wire nut
• (2) Wiring cover screw
a
b
c
d
e
f
g
h
i
j
k
l
m
a
b
g
d
e
f
c
h
l
i
k k
j
m
Do not use the mounting bracket if mounting the fan to a concrete ceiling.
If installing the fan to a junction box, U-shaped ceiling hook, or wood ceiling joist, only
one (1) bolt and one (1) nut are needed. If installing the fan to a J-shaped ceiling hook,
two (2) bolts and two (2) nuts are needed.
Safety cable not shown.
†
††
†††
6REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
PARTS & HARDWARE: UNIVERSAL MOUNT
Mounting bracket
Mounting ball & wedge
Canopy
Extension tube
Wiring cover
(3) Airfoil
Motor hub
Lower cover
Lower cover trim
Remote control
Mounting hardware
• 4 mm self-tapping screw
• 6 mm steel pin
• (6) M4 x 10 mm screw
• (2) M4 lock washer
• Safety cable shackle†
• M6 x 32 mm bolt
• M6 nut
Airfoil hardware
• (6) M5 airfoil screw
• (6) 5 mm lock washer
Wiring hardware
• Wire connectors
• Wire nut
• Cable tie
a
b
c
d
e
f
g
h
i
j
k
l
m
Safety cable not shown.†
a
b
g
d
e
f
k
i
c
h
l
j
m
7
HAIKU®BY BIG ASS FANS
1PREPARE THE FAN SITE
Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable
performing electrical work!
2
1Disconnect Power!
If you are installing the fan directly to the building structure
or to a ceiling-mounted outlet box, the structure or outlet
box must be suitable for fan support.
Disconnect power to the fan location before wiring
the fan!
Mounting Structure
A readily accessible disconnect device shall be
incorporated external to the equipment.
c
b
a
8REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE AIRFOILS
2
Make sure the stickers on the airfoils match the stickers on the fan hub!
1 2
INSTALL AIRFOILS REMOVE PROTECTIVE COVER
9
HAIKU®BY BIG ASS FANS
Moving clockwise around the fan, align each airfoil on the fan hub and secure it with the screws and
washers. Make sure the stickers on the airfoils match the stickers on the fan hub.
Hardware:
a. M5 airfoil screw
b. 5 mm lock washer
Remove and recycle the plastic protective cover (c).
2
1
STEPS COMPLETED
10 REV. F © 2015 BIG ASS FANS. ALL RIGHTS RESERVED.
INSTALL THE LOWER COVER AND TRIM
3
If you purchased the Haiku Light Kit, proceed to the instructions included with the kit. Return to these
instructions once the kit is installed.
1 2
INSTALL LOWER COVER INSTALL LOWER COVER TRIM
Otros manuales para K3150-A2
1
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Admirador de Bigassfans
Bigassfans
Bigassfans K3150-A2 Manual de usuario
Bigassfans
Bigassfans Essence Manual de usuario
Bigassfans
Bigassfans AirEye Manual de usuario
Bigassfans
Bigassfans Haiku 60 Manual de usuario
Bigassfans
Bigassfans powerfoil x2.0 Manual de usuario
Bigassfans
Bigassfans Haiku 52 Manual de usuario
Bigassfans
Bigassfans Powerfoil 8 Plus Manual de usuario
Bigassfans
Bigassfans HAIKU MK-HK4-042406 Manual de usuario
Bigassfans
Bigassfans K3150-A2-XX-XX-03-C Manual de usuario
Bigassfans
Bigassfans 2025 Manual de usuario
Bigassfans
Bigassfans Haiku A0 Series Manual de usuario
Bigassfans
Bigassfans Isis Manual de usuario
Bigassfans
Bigassfans Powerfoil LED Manual de usuario
Bigassfans
Bigassfans Haiku FR127A-A2 Manual de usuario
Bigassfans
Bigassfans es6 Manual de usuario
Bigassfans
Bigassfans AirEye 007180 Manual de usuario
Bigassfans
Bigassfans 8'-24' Powerfoil X Manual de usuario
Bigassfans
Bigassfans Powerfoil 8 Plus Manual de usuario
Bigassfans
Bigassfans Element Manual de usuario
Bigassfans
Bigassfans Pivot Manual de usuario
