Bigassfans Es6 Manual de usuario

BIGASSFANS.COM

es6

EXCEPTIONALLY

ENGINEERED

READ AND SAVE THESE INSTRUCTIONS

À LIRE ET À CONSERVER EN LIEU SÛR

LEA Y CONSERVE ESTAS INSTRUCCIONES

REV. B | 10/09/2020

☑ Prepare Fan Site

Outlet Box: Make sure your outlet box is suitable for fan support. If there is not an

outlet box at the fan location, install one on a ceiling joist or beam.

Concrete Ceiling: Install an anchor hook for the safety cable if required by your

local building and safety code. See the following page for installation details.

Wood Ceiling Joist: Attach the mounting bracket directly to the joist using two

wood screws (not supplied). Recommended: Corrosion-resistant 12-11 x 45 mm hex

head timber screws with seal. If required by local code, mount or embed an outlet

box into the joist. The outlet box must be suitable for fan support.

The mounting/ﬁxing means for attachment to the ceiling such as hooks or other

devices shall be ﬁxed with a sucient strength to withstand four times the

weight of the ceiling fan.

Models and Maximum Weight:

MK-ES61-052306: 25 lb (11.3 kg), MK-ES61-062306: 27 lb (12.1 kg)

Do not use the fan with a dimmer switch.

WARNING: Installation must be in accordance with the requirements set forth

by the National Electrical Code (NEC, United States), ANSI/NFPA 70, and all

national and local codes.

The ground wire must be connected to the supply ground and its length must

be longer than the safety cable.

A means for disconnection must be incorporated in the ﬁxed wiring in

accordance with the wiring rules.

BEFORE YOU START

☑ Turn o Power at Breaker

Input Voltage: 100–277 VAC, 1 Φ, 50/60 Hz

Do not connect the fan to a damaged power

source. Do not attempt to resolve electrical failures

on your own. Contact a licensed electrician if you

are uncomfortable performing electrical work. A

licensed electrician must install the fan if required

by local code.

☑ Gather Tools

Provided with fan

☑ Prepare Concrete Ceiling (if applicable)

Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed

40mm. Remove any dust from the holes. Insert three anchor bolts (not supplied)

into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the

bolt sleeves are ﬂush with the ceiling surface. Position the mounting bracket on the

anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock

the anchors.

If required by local building and safety codes, install an anchor hook (not supplied) for

the safety cable. Drill an Ø 8 mm hole for the anchor hook. The hole depth should not

exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and

fully tighten.

Ø 6 mm

45 mm 43 mm

112 mm

50 mm max

40 mm max

REV. B | 10/09/2020

PARTS AND HARDWARE

EMI ﬁlter not shown.

Mounting Bracket

Lower Cover or Light Kit

Mounting Ball

and Wedge

Canopy Screws (4)

Canopy

6 mm Steel Pin

Downrod

Wiring Cover

M6 x 32 mm Bolt M6 Nut

Airfoils (6)

Wire Connectors

Motor Unit

Wiring and Safety Cable

INSTALLATION

1. Install downrod and wiring harness

Align holes on downrod with holes on motor bracket. Secure downrod with the M6 x

32mm bolt and M6 nut (Fig. 1.1).

Fig. 1.1

M6 x 32 mm Bolt

M6 Nut

Connect wiring harness from downrod to receptacle from motor unit (Fig. 1.2).

Fig. 1.2

Wiring Harness

REV. B | 10/09/20202

2. Install lower safety cable and ground wire

Install safety cable and ground wire lugs with unpainted screws and lock washers

(Fig.2.1).

Fig. 2.1

Ground Wire

(Green)

Safety Cable

Lock

Washer

Screw

Make sure all hardware is secure, and then gently tug cables at top of downrod to

reduce slack (Fig. 2.2).

Fig. 2.2

3. Position wiring cover and canopy

Slide wiring cover down downrod, resting it on the fan hub. Make sure no wires are

visible between the cover and fan hub. Slide canopy down downrod, resting it on the

wiring cover (Fig. 3).

Fig. 3

Canopy

Wiring Cover

4. Install mounting ball

Slide mounting ball over downrod (Fig. 4.1).

Insert 6 mm steel pin into hole at top of downrod, and then slide the mounting ball

upward, seating the steel pin in the inner slots (Fig. 4.2).

Insert wedge into mounting ball and secure with screw. Tighten screw enough to

prevent movement between the mounting ball and downrod, but do not over-tighten

(Fig. 4.3).

Fig. 4.1

MountingMounting

BallBall

Downrod

6 mm Steel Pin

Screw

Wedge

Fig. 4.2 Fig. 4.3

REV. B | 10/09/20204

5. Install mounting bracket

Disconnect power to fan location before installing mounting bracket.

WARNING: Mount only to an outlet box marked acceptable for fan support.

Secure mounting bracket to mounting structure with suitable hardware (not supplied)

(Fig. 5). Outlet box shown. Your mounting structure may dier from the illustration.

Power supply omitted from mounting bracket illustration for clarity.

Fig. 5

Suitable Mounting Hardware

6. Hang fan

Raise fan to mounting bracket. Align rib in mounting bracket with slot in mounting ball,

position mounting ball, and let fan hang freely (Fig. 6).

Gently twist downrod to ensure it is properly seated and will not move during fan

operation.

Fig. 6

Mounting Ball

Mounting Bracket

7. Wire fan

Disconnect power to fan location before wiring fan.

Wire fan as shown using the wire connectors (Fig. 7). Attach green ground wire to

mounting bracket with the unpainted screw. Connect wiring harness from power supply

to wiring harness from downrod, making sure that the wiring and safety cable are routed

in the same direction.

Carefully tuck wiring into outlet box or building structure. Ensure wire connectors are

turned upward and that wires are spread apart with grounded conductors on one side

of the outlet box/mounting structure and ungrounded conductors on the other side.

Fig. 7

North America 100–120 V Australia All other regions

AC Hot/L1

Brown Black Brown or Red Brown

AC Neutral/L2

Blue White Black or Light Blue Blue

PE/Earth Ground

Green with Yellow Green or Bare Copper Green with Yellow Green with Yellow

Supply Power Wire Color Chart

AC HOT/L1

BROWN

AC NEUTRAL/

PE/EARTH

GROUND

BLUE

GREEN &

YELLOW

EMI Filter

Power Supply

Wiring Harnesses

Mounting Bracket

Safety

Cable

RED Wire Connector

REV. B | 10/09/20206

8. Install fan stabilizer (optional, outdoor fans only)

The fan stabilizer is included only if purchased as an outdoor fan accessory.

If you purchased the fan stabilizer kit, ﬁt stabilizer into notches on top of mounting ball

(Fig. 8.1).

Fig. 8.1

Mounting Ball

Fan Stabilizer

Secure stabilizer plate to stabilizer with the M6 x 70 mm bolt and M6 nut (Fig. 8.2).

Fig. 8.2

M6 Nut

Stabilizer Plate M6 x 70 mm Bolt

Tabla de contenidos

Idiomas:

Otros manuales de Admirador de Bigassfans

Bigassfans

Bigassfans AirEye Series Manual de usuario

Bigassfans

Bigassfans COOL-SPACE 350 Manual de usuario

Bigassfans

Bigassfans Element Manual de usuario

Bigassfans

Bigassfans Powerfoil 8 Plus Manual de usuario

Bigassfans

Bigassfans COLD FRONT 300 Manual de usuario

Bigassfans

Bigassfans Essence Manual de usuario

Bigassfans

Bigassfans Isis Manual de usuario

Bigassfans

Bigassfans Haiku 52 Manual de usuario

Bigassfans

Bigassfans 2025 Manual de usuario

Bigassfans

Bigassfans powerfoil x2.0 Manual de usuario

Bigassfans

Bigassfans E7 Manual de usuario

Bigassfans

Bigassfans HAIKU H Series Manual de usuario

Bigassfans

Bigassfans AirEye 007180 Manual de usuario

Bigassfans

Bigassfans Basic 6 Manual de usuario

Bigassfans

Bigassfans Black Jack Manual de usuario

Bigassfans

Bigassfans Pivot 180 Manual de usuario

Bigassfans

Bigassfans Powerfoil X3.0 Plus Manual de usuario

Bigassfans

Bigassfans Haiku A0 Series Manual de usuario

Bigassfans

Bigassfans Basic^ Manual de usuario

Bigassfans

Bigassfans Haiku S3127-A2 Manual de usuario

Bigassfans

Bigassfans HAIKU L Manual de usuario

Bigassfans

Bigassfans AirEye 007180 Manual de usuario

Bigassfans

Bigassfans Haiku FR127A-A2 Manual de usuario

Bigassfans

Bigassfans Haiku UV-C Manual de usuario

Manuales populares de Admirador de otras marcas

ELTA FANS

ELTA FANS H03VV-F Manual de usuario

Hunter

Hunter 20714 Manual de instrucciones

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manual de usuario

Hunter

Hunter Caraway Manual de instrucciones

Panasonic

Panasonic FV-15NLFS1 Manual de usuario

Kompernass

Kompernass KH 1150 Manual de usuario

VES

VES FALA100/12V/TR Manual de usuario

Vertiv

Vertiv Liebert DCD Manual de usuario

Westinghouse

Westinghouse GFP Series Manual de usuario

Venmar

Venmar KUBIX HRV PLUS Series Manual de usuario

Maico

Maico ECR 31 Manual de usuario

Sonnenkonig

Sonnenkonig Dinky Manual de usuario

S&P

S&P ECOWATT HXBR Manual de usuario

Wider

Wider IMP03369BH Manual de usuario

Panasonic

Panasonic F-60DHN Manual de usuario

Hinkley

Hinkley HIGHLAND Manual de usuario

Broan

Broan 766BN Manual de usuario

Premium

Premium PFS16022 Instrucciones de montaje

Bigassfans es6 Manual de usuario

Manuales populares de Admirador de otras marcas