Bigassfans Haiku UV-C Manual de usuario
INSTALLATION GUIDE
HAIKU® BY BIG ASS FANS | REV. C | 08/26/2020
READ AND SAVE THESE INSTRUCTIONS
BEFORE YOU START
☑ Turn O Power
Contact a licensed electrician
if you are uncomfortable
performing electrical work. A
licensed electrician must install
the fan if required by local code.
Do not use the fan with a
dimmer switch.
Turn o power at breaker!
☑ Gather Tools
☑ Prepare Fan Site
Mounting: Sloped or flat ceilings from 11 to 18feet (3.4 to
5.5 meters)
Input Voltage: 100–240 VAC, 50–60 Hz
Outlet Box: Make sure your outlet box is suitable for fan
support. If there is not an outlet box at the fan location,
install one on a ceiling joist or beam.
Concrete Ceiling: Install an anchor hook for the safety
cable if required by your local building and safety code. See
the following page for installation details.
Wood Ceiling Joist: Attach the mounting bracket directly
to the joist using two wood screws (not supplied). Big Ass
Fans recommends using corrosion-resistant 12-11 x 45 mm
hex head timber screws with seal.
☑ Select Extension Tube
Select the appropriate extension tube for your ceiling
height and slope. See page 2 for a guide to select the most
appropriate extension tube.
Ø 6 mm
112 mm
45 mm 43 mm
50 mm max
40 mm max
1
©2020 BIG ASS FANS |ALL RIGHTS RESERVED
Concrete Ceiling
Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed 40 mm. Remove any dust from the holes. Insert three
anchor bolts into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the bolt sleeves are flush with the ceiling
surface. Position the mounting bracket on the anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock the
anchors.
If required by local building and safety codes, install an anchor hook for the safety cable. Drill an Ø 8 mm hole for the anchor hook. The
hole depth should not exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and fully tighten.
2HAIKU® BY BIG ASS FANS | REV. C | 08/26/2020
Choosing an Extension Tube
Consult the tables below to select the appropriate extension tube for your fan.
Ceiling Slope
Haiku fans with a universal mount can be installed on sloped
ceilings with an angle no greater than 33°.
Fan Diameter Maximum
Ceiling Slope Extension Tube
Length
52 in.
(1.3 m) 26° 20 in.
(508 mm)
52 in.
(1.3 m) 33° 32 in.
(813 mm)
60 in.
(1.5 m) 22° 20 in.
(508 mm)
60 in.
(1.5 m) 33° 32 in.
(813 mm)
84 in.
(2.1 m) 16° 20 in.
(508 mm)
84 in.
(2.1 m) 29° 32 in.
(813 mm)
Ceiling Height
For optimum performance, Big Ass Fans recommends the
following extension tube lengths based on ceiling height.
Ceiling Height Extension Tube Length
9.5–11 ft
(2.9–3.4 m) 20 in.
(508 mm)
11–13 ft
(3.4–4 m) 32 in.
(813 mm)
13–14 ft *
(4–4.3 m) * 48 in. *
(1219 mm) *
>14 ft *
(>4.3 m) * 60 in. *
(1524 mm) *
* Big Ass Fans recommends using an extended length
extension tube for ceiling heights over 13 ft (4 m). The fan
comes standard with 20 in. (508 mm) and 32 in. (813 mm)
extension tubes. Other lengths are available by contacting
Customer Service.
3
©2020 BIG ASS FANS |ALL RIGHTS RESERVED
Haiku Remote
Do not expose the remote control to rain or water.
Turns fan on or o. Sets fan timer length of up to eight hours. Each
press extends timer by one hour.
Turns light on or o. Clears active fan timer.
Increases fan speed/light brightness. Varies fan speed to simulate a natural breeze.
Decreases fan speed/light brightness. Automatically adjusts your fan speed overnight to
keep you comfortable while you sleep.
4HAIKU® BY BIG ASS FANS | REV. C | 08/26/2020
INSTALLATION
Safety cable not shown
If the EMI filter is included, install it with your fan.
Mounting Bracket
Canopy
Extension Tube
Lower Cover
M5 Screws (6)
Canopy Screws (4)
Wiring Cover
Airfoils (3)
M6 Nut
M6 x 32 mm Bolt
Grommets (6)
Mounting Ball
and Wedge
Motor Hub
Wire Connectors
6 mm Steel Pin
Light
5
©2020 BIG ASS FANS |ALL RIGHTS RESERVED
Install Airfoils
Remove and recycle the plastic protective cover.
Moving clockwise, align each airfoil on the fan hub and secure
it with the airfoil hardware (Fig. 1). Make sure the sticker color
on each airfoil matches the corresponding sticker color on
the fan hub!
M5 Screw
Grommet
1
Fig. 1
Airfoil
Fig. 2
2Install Lower Cover
Attach the lower cover. Make sure the wiring harness on the
bottom of the fan is tucked into the groove on the fan and the
groove on the lower cover (Fig. 2).
Lower Cover
6HAIKU® BY BIG ASS FANS | REV. C | 08/26/2020
Fig. 3.1 Fig. 3.2
Wiring
Harness
M6 x 32 mm Bolt
M6 Nut
3Attach Extension Tube and Wiring Harness
Align the holes on the extension tube with the holes on the motor bracket, and then secure the tube with the M6 x 32 mm bolt and M6
nut (Fig. 3.1). Make sure the extension tube is not tilted and is perpendicular to the motor hub.
Connect the wiring harness from the extension tube to the receptacle from the motor hub (Fig. 3.2).
7
©2020 BIG ASS FANS |ALL RIGHTS RESERVED
Fig. 4.1
Safety Cable
Ground Wire
(Green)
Lock
Lock
Washer
Washer Screw
Install Lower Safety Cable and Ground Wire
Install the safety cable and ground wire lugs with the unpainted screws and lock washers. Make sure the safety cable lug is oriented
upward as shown (Fig. 4.1).
Make sure all hardware is secure, and then gently tug the cables at the top of the extension tube to reduce slack. Orient the remaining
loose wiring receptacle from the motor hub upward as shown (Fig.4.2).
4
Fig. 4.2
8HAIKU® BY BIG ASS FANS | REV. C | 08/26/2020
Install Light
WARNING: Skin or eye damage may result from directly viewing ultraviolet light produced by the lamp in this apparatus. Always
disconnect power before relamping or servicing. Replace ultraviolet LEDs with Model No. 1050-39-30, manufactured by Big Ass Fans.
Slide the light down the extension tube, resting it on the fan hub. Orient the light so that the tab at the top of the light rests in the groove
at the top of the motor bracket (Fig. 5.1). Be careful not to scratch the extension tube while positioning the light. Connect the wiring
harness on the light to the receptacle from the motor hub. Tighten the set screw at the top of the light (Fig. 5.2).
5
Fig. 5.1
Light
Fig. 5.2
Set Screw
Wiring
Harness
Tab
Motor Bracket
Tabla de contenidos
Otros manuales de Admirador de Bigassfans
Bigassfans
Bigassfans Powerfoil 8 Plus Manual de usuario
Bigassfans
Bigassfans COOL-SPACE 300 Manual de usuario
Bigassfans
Bigassfans AirEye Manual de usuario
Bigassfans
Bigassfans Basic 6 Manual de usuario
Bigassfans
Bigassfans E7 Manual de usuario
Bigassfans
Bigassfans Haiku 52 Manual de usuario
Bigassfans
Bigassfans Isis Manual de usuario
Bigassfans
Bigassfans POWERCOOL Manual de usuario
Bigassfans
Bigassfans X2 Manual de usuario
Bigassfans
Bigassfans Haiku A0 Series Manual de usuario
Bigassfans
Bigassfans Isis Manual de usuario
Bigassfans
Bigassfans 2025 Manual de usuario
Bigassfans
Bigassfans AirEye Manual de usuario
Bigassfans
Bigassfans i6 Manual de usuario
Bigassfans
Bigassfans K3150-A2-XX-XX-03-C Manual de usuario
Bigassfans
Bigassfans Yellow Jacket Manual de usuario
Bigassfans
Bigassfans Powerfoil LED Manual de usuario
Bigassfans
Bigassfans Isis Manual de usuario
Bigassfans
Bigassfans 2025 Manual de usuario
Bigassfans
Bigassfans AirEye Manual de usuario
