BGS technic 8482 Manual de usuario

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Art. 8482

Ball Joint Tool for BMW 3 Series

A professional quality tool designed for easy removal and insertion of press fit control arm ball joints

Suitable for use on BMW 3 series (E36) models

1. Press Frame Assembly

2. Removal Shell

3. Installation Shell

4. Drive Screw with Thrust Bearing

5. Spindle Support

6. Support

7. Removal Bush

8. Installation Bush

WARNING

Before starting work under a car always ensure that it is adequately supported by axle stands or

ramps.

Chock wheels and ensure that the hand brake is firmly applied.

Always work in a well ventilated area.

Always use approved eye protection especially when working under vehicles.

Ensure that tools are correctly mounted.

Always use workshop manual for detailed instructions.

Do not over tighten or use undue force as this can cause damage to both tool and component.

Always lubricate screw thread.

Do not use an impact wrench with this tool

SW-Stahl und Werkzeugvertriebs GmbH Tel. +49 (0) 2191 / 46438-0

F56essartSresukreveL ax +49 (0) 2191 / 46438-40

ed.lhatsws@ofni:liaM-EdiehcsmeR79824-D

Instruction Manual

BGS technic KG

Bandwirkerstr. 3

42929 Wermelskirchen

Tel.: 02196 720480

Fax.: 02196 7204820

[email protected]

www.bgstechnic.com

Extraction Insertion

A = Bush

1. Securely support the vehicle and follow workshop manual instructions to access the ball joint.

Mark the position of the ball joint to ensure the new ball joint is correctly installed.

2. Ensure that the screw threads (4) are clean, in good condition and freely lubricated each time

before use.

3. To remove the old ball joint assemble the tool as shown, using the bright plated shells (2) &

(7). Note ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to

slowly turn the drive screw (4) to extract the ball joint from the control arm.

4. Clean the lower face & bore of the control arm using a wire brush to remove any rust. Do not

apply any grease to the bore or the ball joint taper.

5. To install the new ball joint assemble the tool as shown, using the shells (8) & (3). Note:

ensure the tool is correctly aligned. Use a 16 mm ring spanner / socket & ratchet to slowly turn

the drive screw (4) to insert the ball joint into the control arm. Always lubricate the screw

threads before using the tool.

Tabla de contenidos

Otros manuales de Herramientas de BGS technic

BGS technic

BGS technic 6929 Manual de usuario

BGS technic

BGS technic 1689 Manual de usuario

BGS technic

BGS technic 3201 Manual de usuario

BGS technic

BGS technic 9739 Manual de usuario

BGS technic

BGS technic 74357 Manual de usuario

BGS technic

BGS technic BGS 8156 Manual de usuario

BGS technic

BGS technic 62676 Manual de usuario

BGS technic

BGS technic 7744 Manual de usuario

BGS technic

BGS technic 8492 Manual de usuario

BGS technic

BGS technic 3058 Manual de usuario

BGS technic

BGS technic 70009 Manual de usuario

BGS technic

BGS technic BGS 8857 Manual de usuario

BGS technic

BGS technic 8954 Manual de usuario

BGS technic

BGS technic 70917 Manual de usuario

BGS technic

BGS technic 8882 Manual de usuario

BGS technic

BGS technic BGS 2999 Manual de usuario

BGS technic

BGS technic 9655 Manual de usuario

BGS technic

BGS technic 8648 Manual de usuario

BGS technic

BGS technic 9637 Manual de usuario

BGS technic

BGS technic BGS 67302 Manual de usuario

BGS technic

BGS technic 8216 Manual de usuario

BGS technic

BGS technic 1480 Manual de usuario

BGS technic

BGS technic 8651 Manual de usuario

BGS technic

BGS technic 8261 Manual de usuario

Manuales populares de Herramientas de otras marcas

Martor

Martor SECUNORM 175 Manual de usuario

ERKCO

ERKCO 1000 Manual de usuario

jbc

jbc N4473 Manual de usuario

FEINMETALL

FEINMETALL FZWZ-SET-001 Manual de usuario

Worx Professional

Worx Professional Sonicrafter WU676 Manual de usuario

Gage Bilt

Gage Bilt GB713SH Manual de usuario

Hilti

Hilti DX 9-ENP Manual de usuario

norbar

norbar NORTRONIC 34399 Manual de usuario

Makita

Makita DHR241 Manual de usuario

Motor Guard

Motor Guard JMB-1250 Manual de usuario

Power Adhesives

Power Adhesives 805-12 Manual de usuario

Clemco

Clemco 24189 Manual de usuario

VVG

VVG VNG 903 Series Manual de usuario

Hilti

Hilti FX 3-A Manual de usuario

Grizzly

Grizzly H6472 Manual de usuario

axing

axing BWZ 5-02 Manual de usuario

Dh-Robotics

Dh-Robotics RGI-100 Cómo utilizar

Goobay

Goobay 97790 Manual de usuario