Beok Controls BOT-205 Manual de usuario

BOT-205-X Wireless Heating Thermostat User Manual

Programmable Mode Setting

Power on state, long press “ ” enter into first time period (hour setting), press “ ” and “ ” to

adjust value, short press “ ” enter into minute setting, press “ ” and “ ” to adjust value, then short

press “ ” enter into temperature setting, press “ ” and “ ” to adjust value, successively short press

“ ” to set second time period, thirdly time period ......

Wake up

Out door

Back home

Out door

Back home

Sleep

6：00 20℃8：00 15℃11：30 15℃13：30 15℃17：00 20℃22：00 15℃

Product Specifications

☆Power Supply: Receiver:230Vac 50/60HZ

☆Range of temperature display: 0~40°C

Advanced options

Power off state, long press

From A1 to Ao, short press

Transmitter: 2AA* 1.5V alkaline batteries

for 3-5 seconds to access advanced setting.

to choose the option, and adjust data by

☆Display accuracy: 0.5°C

☆Insulating condition: Normal environment

☆Running program: Set per 1 week as a cycle

. After finish setting ,remain

☆Probe sensor: NTC(10k)1%

about 5 seconds ,it will save setting and exit advanced setting automatically .

☆Contact capacity: 5A/250V(BW;WW);16A/250V(WE)☆Output: Switch relay

Setting Options

Data Setting Function

Factory Default

Display

☆Working environment temperature: 0~70°C

☆Range of temperature adjustment: 5~35°C

Operation Key

☆Installation: Wall mounted or on battery seat

☆Size(mm)：86*86*27

Measure Temperature

Calibration

-9-+9℃

measuring

temperature

1℃

press

, to adjust.

symbols represent

Temperature

control

return 0.5-2.5℃

Turn ON/OFF: Short press to turn on/ turn off

difference setting

A3 Children lock setting

A4 Power off Memory

0:half lock

1:full lock

1 Short press

to switch automatic mode and manual mode

for 3-5 seconds to enter into programmable

2 Turn on thermostat, long press

0: Last State

setting

1: Electricity turn off

3. Turn off thermostat, long press

for 3-5 seconds to enter into advanced setting

2: Electricity turn on

1 Confirm key: use it with

key

P1: 5+2

P2: 6+1

P3: 7

2 Only short press it to set time

A5 Weekly programming selection

A6 Setting temperature lowest limit

3 Turn on thermostat, long press it for 3-5seconds to holiday mode setting

1-10℃

5℃

1 Decrease key

2 Long press to lock /unlock

1 Increase key :

A7 Setting temperature highest Limit 20-70℃

1: 1-10℃

35℃

2 Under auto mode state, press

to enter into temporary manual mode

A8 Anti-freezing function

2: more than 10℃,display -- ,then

mean closed this function

1: 5-35℃

5℃

3 Long press to check external sensor temperature(only used for the receiver with

external sensor)

Highest temperature protection 2: less than 35℃,display --,then mean

function closed this function

Icon Instruction

Return different temperature of 1-9℃

external sensor

Display A o, long press

the whole screen

until show

Ao Restore factory defaults

Power off state, long press

From B1 to B5, short press

for 3-5 seconds to access advanced setting.

to choose the option, and adjust data by

. After finish setting ,remain

about 5 seconds ,it will save setting and exit advanced setting automatically .

NO Setting Options Data Setting Function

Wiring Diagram

Factory

Default

B1 IP code low setting

B2 IP code high setting

00-FF

01-FF

Power on RF Receiver ,continue press

until Display”55” means IP match

successfully.

B3 Write transceiver IP address

B4 Choose “C” or “F” display

0: C ( Celsius)

1: F (Fahrenheit)

B5 Version No.

10：V1.0

Setting IP code

Cautions on Installation and Use

Turn on the receiver, and keep the transmitter on power off state, long press button

enter into setting interface.

for 3-5 seconds to

To prevent the thermostat display from a high fluctuation, special treatment has been made to the program. Therefore,

it is normal that the thermostat cannot immediately display the sudden change of temperature.

The thermostat installed on 1.5m above the ground.

B1:press or to set any number or letter(if you have more than one transceiver, make sure to set

different number or letter for each transceiver )

For the thermostat installed, please take care not to install it to the wall corner, door / window side or behind the door

or in such unheated area as exterior wall. Avoid hot / cold air duct, radiator, flue or thermal pipe.

If you have any problem for the installed ,please contact our company hysen, we will make a demonstration for you

Only the professional technicians are permitted to open the transmitter and receiver box of the thermostat for

installation. When install the power supply, make sure that the power cable is well insulated.

The thermostat is unrepairable product. The user shall not open the internal circuit board.

Then press

transceiver, make sure to set different number or letter for each transceiver )

Then press to switch to B3 , continuously click until the transmitter display “55”means that

to switch to B2:press or to set any number or letter(if you have more than one

matched successfully

Transceiver tips

Receiver LED display instruction:

Power light (green light):it’s bright when power on

Before installing the thermostat, make sure that the system is disconnected. The maximum voltage of the system shall

meet therequirements specified intheInstruction Manual(Max. AC Voltage: 240V).

Signal light(orange light):it’s bright within 10s after power on (match IP),signal light off when it receive

match, signal light is blinking within 10s after power off.

Load light/fault light (red light):

A、When no fault: light bright when load output, light off when no load output

B、When fault: 1. Light blink 2 times indicate IP is fault

Warranty：

We offer the warranty of 24 months, from the sales day. The products of our company can have lifetime

warranty ,if it is not the quality problems, or beyond the warranty period, we will charge for the after-sale

service.

2. Light blink 3 times indicate it does not receive wireless signal for 1 hour

3. Light blink 4 times indicate built-out sensor is fault(only for receiver with external

sensor )

Sensor fault display: please choose correct working way of built-in and external sensor, if choose

wrongly or sensor fault (breakdown), “E1”or “E2”will be displayed on the screen. Thermostat will stop

heating until the fault is eliminated.

Otros manuales de Termostato de Beok Controls

Beok Controls

Beok Controls BOT-313 Manual de usuario

Beok Controls

Beok Controls TOL63R Manual de usuario

Beok Controls

Beok Controls TDS21WIFI-AC2 Manual de usuario

Beok Controls

Beok Controls TDR89 Manual de usuario

Beok Controls

Beok Controls TDS23M Manual de usuario

Beok Controls

Beok Controls TGR-85 Manual de usuario

Beok Controls

Beok Controls TGR-86 Manual de usuario

Beok Controls

Beok Controls BOT-R315 Manual de usuario

Beok Controls

Beok Controls TOL43-AC Series Manual de usuario

Beok Controls

Beok Controls TDS21-AC Manual de usuario

Beok Controls

Beok Controls TGR87 Series Manual de usuario

Beok Controls

Beok Controls TGR87WIFI-WP Manual de usuario

Beok Controls

Beok Controls TOL47 Series Manual de usuario

Beok Controls

Beok Controls TGR87 Series Manual de usuario

Beok Controls

Beok Controls TDS23WIFI-AC2 Manual de usuario

Beok Controls

Beok Controls TDS21 Manual de usuario

Beok Controls

Beok Controls TGR-86 Manual de usuario

Beok Controls

Beok Controls TGP51GWIFI-EP Manual de usuario

Beok Controls

Beok Controls TDS23-AC2 Manual de usuario

Beok Controls

Beok Controls TGT70 Manual técnico

Beok Controls

Beok Controls TOL63R Manual de usuario

Beok Controls

Beok Controls TGP51 Manual de usuario

Beok Controls

Beok Controls TDS23 Manual de usuario

Beok Controls

Beok Controls TGR-86 Manual de usuario

Manuales populares de Termostato de otras marcas

EWELLY

EWELLY EW-181 Manual de usuario

Prolon

Prolon T1100 Instrucciones de instalación

Computherm

Computherm Q20 Manual de usuario

Heatmiser

Heatmiser neoStat Manual de usuario

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manual de usuario

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manual de usuario

Saswell

Saswell SAS920XWHB-7-S-RF Guía

Aircalo

Aircalo TFP1-ET85P2 Manual de usuario

Honeywell

Honeywell CM721 Manual de usuario

Carrier

Carrier DEBONAIR 33CS Manual de usuario

Lennox

Lennox iHarmony Zone Thermostat Instrucciones de montaje

Gemtech

Gemtech GT7000 Manual de instrucciones

Rollei

Rollei Smartes 45000 Manual de usuario

Sinope

Sinope TH1300RF Manual de usuario

Honeywell

Honeywell RLV4305 Manual de usuario

Honeywell

Honeywell Prestige 2.0 THX9421 Manual de usuario

NuTone

NuTone NTBZ48 Instrucciones de funcionamiento originales

Stelpro

Stelpro MAESTRO ASMT402AD Manual de usuario