Bemodern Arteon Pryzm 10003SL Guía

Evento Timber Suites To Suit:

Arteon 10003SL & 12503SL Fires

Instructions for Installation

R1 DEC 2020 200805_1

Contents

Technical Specs 3

Contents of Fixings Box 4

Installation –Timber 5 –8

Maintenance 9

200805_1

Technical Specification

Fire Surround Logs Dimensions (mm)

A B C D E

ARTEON PRYZM

5D 1000 3SL

54” EVENTO

TIMBER FLOOR

STANDING

61270 271 842 320 1370

ARTEON PRYZM

5D 1250 3SL

64” EVENTO

TIMBER FLOOR

STANDING 81520 296 842 345 1620

Note: The Arteon Fire and Evento Surround are boxed separately- Light Assembly of the Evento Surround is

required- Please follow the steps detailed below.

Fire Visible Glass Area (mm)

F G H

ARTEON PRYZM

5D 1000 3SL 995 380 152

ARTEON PRYZM

5D 1250 3SL 1245 380 177

200805_1

What is in the box (s)

Box- 050237 (to suit the 1000 3SL) or Box 050253 (to suit the 12503SL)

200805_1

Please ensure all fixings are present before commencing installation. If anything is missing please call Customer

Services on 01914300901 or email us at [email protected].uk

8X 3.5 X 16.5 mm

Pozi Flange Head

Metal Sides

Quantity Description Quantity Description

1ARTEON PRYZM 1000-3SL- Electric Fire Engine 1 Rear Bracket ( Not Required For This Installation)

6 Logs (Small Box Inside Fire) 1 Fire Remote Control & 2 x AAA Batteries (Large Box Inside Fire)

2 Bags of Crystals (Large Box Inside Fire) 4 Short Side Brackets (Large Box Inside Fire)

3 Bags of Pebbles (Large Box Inside Fire) 2 Long Side Brackets (Large Box Inside Fire)

2 Bags of Bark (Large Box Inside Fire) 1 Power Cable, Plug & IEC (1.8M) (Large Box Inside Fire)

2 Bags of Grey Slate (Large Box Inside Fire)

Box- 050164 –(1000-3SL)

Quantity Description Quantity Description

1ARTEON PRYZM 1250-3SL- Electric Fire Engine 1 Rear Bracket ( Not Required For This Installation)

8 Logs (Small Box Inside Fire) 1 Fire Remote Control & 2 x AAA Batteries (Large Box Inside Fire)

3 Bags of Crystals,(Large Box Inside Fire) 4 Short Side Brackets (Large Box Inside Fire)

3 Bags of Pebbles (Large Box Inside Fire) 2 Long Side Brackets (Large Box Inside Fire)

3 Bags of Bark (Large Box Inside Fire) 1 Power Cable, Plug & IEC (1.8M) (Large Box Inside Fire)

3 Bags of Grey Slate (Large Box Inside Fire)

Box- 050172–(1250-3SL)

Depending on the product size purchased:

Quantity Description

2 Metal Sides LH/RH- 601407

8 3.5 x 16.5mm POZI FLANGE HEAD screws bagged.

1 Downlight Instructions.

1 2M Downlight Mains Cable (Supplied to be used with a fused spur. i.e. A 3

Amp Switched Fused spur or 3 Amp 3 Pin Plug if using a double socket.

1 830mm Fly Lead- Required to connect the LED Lights to the Fire.

Quantity Description

1EVENTO- Assembled Top- with pre-installed Downlight Set & Sensor.

1EVENTO- Assembled Base- with pre-installed LED Light Set.

Also in Boxes 050237 & 050253, there is a smaller box ( Labelled A) containing

the following: 1X Downlight

Mains Cable

1X 830mm

Fly Lead

Installation –Timber

Before the surround can be installed, consideration will need to be given routing the power supply to the fire. This

will affect the stages of the installation process. We advise a qualified electrician conduct any electrical parts of the

installation.

Note: A double socket is required or a single socket and a 3 Amp switched fused spur for the operation of the

Fire and the preinstalled Downlights.

Unpack your new suite- DO NOT dispose of the packaging until you have checked and made sure all the parts and

fixings listed on Page 4 are present. Tip: To help avoid damage of the assembled parts place them on the surplus

packaging, whilst they are waiting to be installed.

Note: This installation guide is detailed for both 54” and 64” sized surrounds so please familiarise yourself with

the model you have purchased before beginning installation.

Note: The surround and fire are a two adult person lift. A second person will be required to lift and support

the surround and fire during installation.

200805_1

Once the Fire has been prepared, lift the unpacked

Assembled Base into position.

Remove any obstructions, i.e. mark and cut to shape

or remove any skirting to allow the Assembled Base to

butt up flush to the wall.

See Diagram 2.

Note: The Assembled Base is a two adult person lift.

Diagram 1

Position the Assembled Base away from the wall,

leaving enough space to the rear to allow the Fire and

Metal Sides to be installed in the following steps.

See Diagram 3.

Diagram 2

Preparing the fire- See the separate Fire Instructions.

Locate the box containing the Fire-050164 or 050172

depending on the version purchased and locate the

Fire Instructions.

Please refer to the Pages 8-9, in the Fire Instructions

and follow the steps to remove the Glass and Rear

Bracket and the internal cardboard boxes.

Please refer to Page 10- Diagram 11 in the Fire

Instructions to prepare the Fire for a 3 Sided

installation.

Diagram 3

Installation –Timber continued

200805_1

Ensure the Fire is positioned centrally in the cut out of

the Assembled Base and that the Fire is pushed up tight

against the front of the opening.

See Diagram 5.

Diagram 5

Locate the 2 x Metal Sides , these are packaged in the

small cardboard box, (Box A- found inside the surround

box), along with the 8 x 3.5 X 16mm Pozi Flange Head

Screws, required for fixing.

Note: Remove any protective film before installing.

Position the 2 x Metal Sides with the tab at the top.

Line up the holes in the Metal Sides with the pre-drilled

holes on the Assembled Base .

See Diagram 6.

Diagram 6

Once aligned, fix the Metal Sides to the Assembled Base

using 4 x 3.5 X 16mm Pozi Flange Head Screws

provided.

See Diagram 7.

Tip: If the holes do not align go back to step 4 and

ensure the Fire has been positioned centrally in the

opening of the Assembled Base.

Note: Ensure the glass and cardboard boxes inside

the fire have been removed before proceeding

further, this will reduce the handling weight.

Lift the Fire into the cut out in the Assembled Base,

ensuring the Fire is sitting on the two central supports.

See Diagram 4.

Note: The fire is a two adult person lift.

Diagram 4

Diagram 7

Installation –Timber continued

10.

Diagram 10

11.

Diagram 11

Lift the partially assembled surround against the wall.

Ensuring the Metal Sides are plumb - mark the location

of the fixing points on the wall behind.

See Diagram 9.

Remove the partially assembled surround from the wall

and drill and plug the fixing points.

Note: Plugs and fixings are not supplied- See Important

Note on Page 9.

Note: This is a two adult person lift.

Diagram 9

200805_1

Note: Once the partially assembled surround has been

secured to the wall, connect the pre-installed Downlights

to the mains cable, checking that the lights and sensor are

working correctly.

If there are any problems please call Customer Services on

01914300901 or email us at

customerservices@bemodern.co.uk

Finally return the partially assembled surround against the

wall.

Note: Great care must be taken to avoid crushing or

damaging the cables on installation.

Note: Ensure the Downlight mains cable (white cable) is

routed in a way that it can be connected to the pre-

installed Downlights in the Assembled Top when it is

positioned in a later procedure. See Diagram 11.

Once routed correctly, proceed with fixing the surround to

the wall. See Diagram 10.

Diagram 8

(Please refer to Page 11 in the Fire Instructions, before

proceeding further and ensure the Power Cable and LED

Light Set are connected to the relevant connection

ports.

See Diagram 8.

Note: At this stage also wire in or plug in the mains

cable for the Downlights. (The cable found in the

smaller cardboard box that comes with the surround.)

Installation –Timber continued

14.

Diagram 14

13.

Diagram 13

200805_1

Line up the holes in the Metal Sides with the pre-drilled

holes on the Assembled Top.

Once the holes are aligned, fix to the Assembled Top

using 4 No. 3.5 X16mm Pozi Flange Head Screws

provided.

See Diagram 14.

Note: DO NOT seal around the edges of the top

between the wall- access to the downlights and

sensor may be required in the event of failure.

Once the installation is complete, please refer to Page 15

in the Fire Instructions (with the Fire), for advice on how

to dress the Fuel Bed and position the Logs.

Once the Logs and Fuel Bed have been dressed

remember to replace the Glass- securing with the

previously removed Screws. Please refer to Page 16 in

the Fire Instructions.

For the Fire User Instructions, please refer to Pages 17-

23, in the Fire Instructions.

12.

Diagram 12

Ensure the Assembled Top is centralized on the Metal

Sides, before fixing in position.

There should be approx. 21mm overhang each side.

See Diagram 13

15.

Diagram 15

Lift the Assembled Top into position.

Note: The Assembled Top is a two adult person lift.

Note: Great care must be taken to avoid crushing or

damaging the Downlight cables during installation.

See Diagram 12.

Maintenance

WARNING: Before any maintenance or whilst cleaning the exterior of the fireplace, the unit should

be disconnected from the power supply until it has cooled down.

Cleaning the Furniture

To maintain the appearance of your new suite we recommend that it dusted using a lint free cloth.

NEVER use any form of abrasive or DAMP cloth.

Cleaning the Fire and the Metal Sides

Cleaning or polishing products is not recommended. Fingerprints or other marks on the front glass

panel and metal sides can be removed by using a piece of soft, damp, lint-free cloth with a good quality

household glass cleaner. The front glass panel should always be completely dried with a clean, lint-free

cloth or paper towel.

CAUTION: Abrasive cleaners should not be used on the glass panel. Liquids should not be sprayed

directly onto any surface of the unit.

Troubleshooting

Should you have any queries regarding this product please contact Customer Services on

01914300901 or email us at customerservices@bemodern.co.uk

Recycling

All cardboard packaging is recyclable.

200805_1

IMPORTANT NOTE:

Wall fixings (i.e. screws/wall plugs etc.) are not supplied as these are crucially dependent upon the type of wall and

surface the surround is going to be fixed too.

The installer is therefore responsible for ensuring that suitable fittings are used as well as individual fitting situations

and environments. All mechanical fixings, for holding the surround in position, must be secured to a solid wall or

structure.

Otros manuales para Arteon Pryzm 10003SL

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Chimenea de interior de bemodern

bemodern

bemodern ELSIE 960 Manual de usuario

bemodern

bemodern 2893 Manual de usuario

bemodern

bemodern 580 Deluxe Inset Manual de usuario

bemodern

bemodern Arteon Pryzm 10003SL Manual de programación

bemodern

bemodern 2603 HE900E Instrucciones de instalación

bemodern

bemodern Pryzm 750 Manual de usuario

bemodern

bemodern 2668 Manual de usuario

bemodern

bemodern Arteon 4119 Manual de usuario

bemodern

bemodern BM-05XXX1 Manual de usuario

bemodern

bemodern Arteon Pryzm 10003SL Guía

bemodern

bemodern EARDF16NG Guía del usuario

bemodern

bemodern 2599M Manual de usuario

bemodern

bemodern Juliette Instrucciones de montaje

bemodern

bemodern 800CF Manual de usuario

bemodern

bemodern BM-091 2 Series Manual de usuario

bemodern

bemodern Pryzm 1000 Manual de usuario

bemodern

bemodern 2599R Manual de usuario

bemodern

bemodern Arteon Pryzm 10003SL Manual de usuario

bemodern

bemodern Beadnell Manual del propietario

bemodern

bemodern HANSFORD GRANDE Manual de programación

bemodern

bemodern 2983 Manual de usuario

bemodern

bemodern BM-081 2 Series Manual de usuario

bemodern

bemodern BROSELEY EVOLUTION Canterbury Remote Manual

bemodern

bemodern Pryzm 750 Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación