WiFi indicator light instruction:
•o No WiFi signal, the heater is not
ready to connect
••ash by 0.1s on and 0.1s o EZ mode
••ash by 1s on and 3s o AP mode
••keep on The heater is conneced to WiFi
••keep on The heater has a problem
connecting to or nding the
WiFi signal. Please do the
following:
• Turn the heater OFF and
ON again
• Restart the WiFi router
• Make sure it is under 2.4
Ghz WiFi router
Connect WiFi:
• There are two ways to connect WiFi: EZ mode and AP mode.
Usually we recommend to connect WiFi by EZ mode, but if EZ
mode doesn’t connect sucessfully, you can try AP mode again.
• Factory default WiFi setting is WiFi indicator light “ o”.
• Press WiFi button one time, change to EZ mode.
• Press and hold WiFi button for 3 seconds, change to AP mode.
• Press and hold WiFi button for 3 seconds again, change to EZ
mode again. It means you can change EZ to AP or AP to EZ by
press and hold WiFi button for 3 seconds.
Delete WiFi:
If the heater is connected to WiFi, press and hold WiFi button for
3 seconds to delete WiFi, and it will return to factory default WiFi
setting“ o ”.
Operations
Turn on:
Plug in and switch on the heater, the heater will enter into standby
mode, and show“OF”on display. Press button to turn on the
heater, and show factory default setting temperature 22°C on
display
Temperature setting:
• Temperature setting range is 5°C–35°C.
• Default temperature setting is 22°C.
• Press or button to set temperature, the temperature
will increase or decrease by 1°C after each pressing. It will show
setting temperature on display after setting.
Timer:
• Press button,“00”ash on display, then press or
button to set timer. Each pressing is 1 hour. Press button to
save setting, or wait 15 seconds to save automatically. Timer
indicator light will keep on red after setting.
• Timer set range is 0 to 24 hours.
• Press button again to modify or cancel timer setting.
• After timer close, the heater will enter into standby mode, and
press button to turn on the heater.
Open window function
• The heater has an open window function.
• Default setting of open window function is closed.
• Press and hold button for 5 seconds, display show “F0”, then
press button to open open window function, display show
“ON”, and press button to close open window function,
display show“OF”, then press button to save setting, or wait
15 seconds to save automatically.
• Open window function description:
1.If you open a window widely in the space where the heater is
located and the temperature drop 2°C or more than 2°C in two
minutes, a sensor will detect the sharp drop in temperature. The
heater will switch out automatically and show“F0” in display.
2.The heater will be reignited automatically after 10 minutes.
However you can manually relight the heater before the 10 minutes
end by pressing . The icon“F0”disappears and show previous
operation mode.
Resetting the heater
• Turn o the heater’s main switch.
• Press and hold while you turn on the heater’s main switch.
Memory function
The heater remembers all the temperature settings and will
automatically return to the desired temperature after a power
failure. If your heater is connected to WiFi it will automatically
reconnect with WiFi (where all temperatures are saved) after a
power cut.
Maintenance
For cleaning, always unplug the heater and leave it to cool.
Wipe the heater regularly with a damp cloth and dry the surface
before turning on the heater again.
The heater must be cleaned at least once a month during the
heating season.
CAUTION! The heater should never be immersed in water.
Avoid using detergents to clean the heater.
Never let any water get inside the heater; this can be hazardous.
Dust etc. should be removed with a soft cloth.
The heater can be stored in a dry and clean place.
Warranty
The warranty is valid for 2 years. The heater will be repaired or
replaced during this time should any malfunction occur. The
warranty applies if the heater is used according to these instructions
and the customer can present a purchase receipt. If the heater
malfunctions in any way, please contact the store where it was
purchased or the importer.
Waste disposal
The symbol indicates that this product is not to be disposed
of together with household waste. This product must be
delivered to a recycling service or container for electrical
appliances and electronic equipment. This is done to
avoid health risks and prevent harm to the environment. Local
businesses (or the environmental station in your neighborhood) are
required by law to accept and recycle such products, as a means of
environmentally sound disposal.
