Belkin F5U234 Manual de usuario

Hi-Speed USB 2.0

4-Port Hub

Connect up to 4 Hi-Speed

USB 2.0 or 1.1 devices

F5U234User Manual

Hi-Speed USB 2.0

4-Port Hub

Connect up to 4 Hi-Speed

USB 2.0 or 1.1 devices

F5U234User Manual

Table of Contents

Introduction ...............................................................................................1

Overview .....................................................................................................2

Features ...............................................................................................2

Package Contents ................................................................................2

Technical Specifications ......................................................................3

Installation .................................................................................................4

Information .................................................................................................7

Introduction

Welcome to Belkin USB 2.0!

Congratulations and thank you for purchasing the Belkin Hi-Speed USB 2.0

4-Port Hub (the Hub). The Hub provides four downstream USB ports that

offer backward-compatible, Plug-and-Play connectivity with all USB devices,

including USB 1.1 (or low- and full-speed) devices, as well as with USB

2.0 (or high-speed) devices. This includes such peripherals as scanners,

printers, mass-storage devices, and high-resolution cameras. The Hub is

self-powered, which allows the cascading of devices with additional hubs, so

that up to 127 USB devices may be connected to a single port.

The Hub is uniquely designed to allow the user to position the four

downstream ports toward the back of the desktop for efficient cable

management, or to the front of the desktop for easier port access. The Hub

also provides a status LED for each individual port and a master power LED.

Overview

Features

• Compliant with Universal Serial Bus specification 2.0

(data rate 1.5/12/480Mbps)

• Backward-compatible with Universal Serial Bus specification 1.1

(data rate 1.5/12Mbps)

• Compatible with Windows® 98 SE, Me, 2000, and XP

• Approved by USB Implementers Forum (USB-IF)

• Supports Plug-and-Play specifications

• Supports “hot swapping” of USB devices

• Over-current detection and protection

• Individual port-status indicator LEDs

• Four 480Mbps downstream ports

• Fully compatible with USB 1.1 and USB 2.0 devices

• Compact, slim-line design

• Multiple hubs may be stacked on top of one another

Package Contents

• Hi-Speed USB 2.0 4-Port Hub

• AC Power Adapter

• User Manual

• USB device cable

Technical Specifications

Upstream Ports (1)

Downstream Ports (4)

Power Mode Self-powered/bus-powered

Per-Port Voltage DC +5V

Per Port Current Self-Powered Mode: 500mA (max)

Bus-Powered Mode: 100mA (max) (Ports one and two only)

Operating Temperature 5º C ~ 40º C

Storage Temperature -20º C ~ 60º C

Enclosure ABS

Power Supply

Output: DC 5V, 2.1A

Plug Size: 3.5mm (outer)

1.0mm (center)

Plug Polarity: Center Positive

Main Power LED Color Definitions:

Off Not operational

Red Operational

Port Status LED Color Definitions:

Off Not operational, or no device connected

Green Fully operational

Amber Over-current condition

Important Note: Please do not connect any USB devices to the Hub until

instructed to do so in step 4 of this installation procedure.

Overview

Important Note: Please do not connect any USB devices to the Hub until

instructed to do so in step 4 of this installation procedure.

1. Plug the AC adapter into a wall outlet, or surge suppressor. Plug the DC

connector into the DC Power Jack found on the side of the Hub.

Important Note: The Hub may be used without the power supply when

connecting devices that draw 100mA of current or less, however, only port 1

and port 2 will be functional.

2. Plug the flat end of the provided USB device cable into the downstream

port of your computer or downstream port of another hub, then plug the

mini 6-pin connector of the device cable into the upstream port on the

rear of the Hub.

Important Note:The Hub must be connected to a USB 2.0-compliant host

in order to function in high-speed mode (480Mbps data rate). If the Hub is

connected to a USB 1.1-compliant host, it will operate only in low-speed or

full-speed mode (1.5Mbps/12Mbps).

3. Windows will now detect your Hub and install the required driver support.

(The Windows “Install New Hardware Wizard” may prompt you to provide

your Windows Installation CD to complete the driver installation process).

Important Note: High-speed hub drivers are included with most USB 2.0 PCI

upgrade cards, and are pre-installed along with the PCI card drivers. If you

purchased an upgrade card prior to the release of high-speed hub support,

please check with your PCI card vendor for an updated USB 2.0 driver. The

Belkin USB 2.0 driver supports all competitive cards based on the NEC host

controller with the exception of Adaptec. The most recent Belkin driver is

available at www.belkin.com.

Installation

4. Plug the USB-A connector of the USB device, or an additional hub, into any

of the downstream ports of the Hub.

Important Note: When moving a device from one port on the Hub to another,

it may be necessary to reinstall the USB drivers for that device.

Installation

Tabla de contenidos

Idiomas:

Otros manuales de Cambiar de Belkin

Belkin

Belkin F1DN204MOD-PP-4 Manual de usuario

Belkin

Belkin F1DP108A - OmniView SMB CAT5 KVM Switch Guía de inicio rápido

Belkin

Belkin F1DN102MOD-HH-4 Manual de usuario

Belkin

Belkin F1U123-KIT Manual de usuario

Belkin

Belkin Wireless Gplus Notebook Card Manual de usuario

Belkin

Belkin 16-Port Gigabit Switch Manual de usuario

Belkin

Belkin OmniView PRO3 PS/2 Manual de usuario

Belkin

Belkin F5U304EAWHT Manual de usuario

Belkin

Belkin F5U303 Manual de usuario

Belkin

Belkin THUMB HUB F5U218-MOB Manual de usuario

Belkin

Belkin OmniView F1DH102U Guía de inicio rápido

Belkin

Belkin F1DN104a Manual de usuario

Belkin

Belkin F1DE101H Manual de usuario

Belkin

Belkin FIREWIRE 1394 Manual de usuario

Belkin

Belkin OmniView F1DP108Gea Manual de usuario

Belkin

Belkin F1DJ104P-B Manual de usuario

Belkin

Belkin F5D5141-5 Manual de usuario

Belkin

Belkin F1DN104F-3 Manual de usuario

Belkin

Belkin Switch Manual de usuario

Belkin

Belkin OmniViewIP 5216K Manual de usuario

Belkin

Belkin P73371-F5U524-G Manual de usuario

Belkin

Belkin F1DN102KVM-UN-3 Manual de usuario

Belkin

Belkin F1DN104B-3 Manual de usuario

Belkin

Belkin OmniView F1DZ102T Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario