Behringer X32 DIGITAL MIXER Manual de usuario
X-32-Control user manual
Versions
No version info yet, since this is the first version.
Installation
Installation should be easy. Just make sure your computer is connected to the internet because the
setup program most likly needs to do some additional downloading.
Unpack the zip file to a folder and run the setup program.
Just follow the screens from here.
After installation is complete, you no longer need to be connected to the internet.
Hardware setup
o make everything work, the three devices, X- ouch, X32 (or M32) mixer and the computer
should all be connected together via ethernet cables. he simplest way to do this is via a network
switch. Just connect all three devices with an ethernet cable to the switch.
If you plan to do remote controlling via phone or tablet, you should connect a wireless router. he
setup of a wireless router is beyond this manual. Please consult its manual or the internet for this.
But basically you do the same thing, connect all three devices to the router via an ethernet cable
(make sure to use only the lan ports and not the – usually different colored – wan port)
configuration
You will need to setup the ip addresses of the three devices. Use a static ip address and keep note of
the ip address you chose for each each device.
It is also important that you set the slave ip address in the X- ouch to the ip address of the computer
that will be running this program and X32-Edit.
Before starting the program, first start X32-Edit and make connection to the mixer. est it to see if
everything is ok.
It is also very important that you do not press the scan button on the X- ouch (the last encoder).
It will say no link, followed by the ip address of the computer (this is the slave address).
Leave it like this for now.
When you first start X32Cntrl, the program will ask the ip address of the mixer and the ip address of
the X- ouch. his will only be asked once, after that the program remembers it.
If you ever want to use different ip addresses for the X- ouch or the mixer, you can go to the
command prompt in windows and type: X32Cntrl -c
he -c option tells the program that you want to configure again and it will ask the ip addresses
again.
Once the program is started, the X- ouch should come to life.
Using X-32-Control
New button layout
X-32-Control changes the functions of the buttons on the X- ouch controller. Below is a picture of
the new button layout:
A magnetic overlay will become available soon.
Channel strip
The channel strip buttons are a bit different than what Behringer uses.
They basically open the respective tab on the X32-Edit application.
All parameters of that tab page can be changed by the use of the encoder nobs and the channel
buttons.
The channel strip contains the following buttons:
Config
The config button activates the config tab on the X-32-Edit application. It brings up the channel
configuration for the selected channel.
The configuration parameters are adjustable with the encoder nobs and the rec (clip) buttons on the
X-Touch.
You can see the selected channel on the first scribble strip as well as on the upper left of the X-32-
Control app.
To change the selected channel, turn the first encoder nob or press one of the 8 select buttons on
the X-Touch.
Turning the first encoder nob lets you switch between all the channels that are present on the
current layer. More on layers later
Important: do not clic the channel on the X-32-Edit tool, if you do so, only the screen will change,
but the encoder nobs still control the previous selected channel.
You can pres the channel select buttons, they will also change to the channel that is currently
assigned by the corresponding fader.
The second encoder lets you change the gain or trim level (depending on the channel source)
You can also change the input source for this channel. To do that, press and hold the button down
while you turn.
Phantom power can be turned on or off by pressing the rec (clip) button under the third encoder.
Polarity can be turned on or off by pressing the rec (clip) button under the fourth encoder.
Stereo lin can be turned on or off by pressing the rec (clip) button under the fifth encoder.
The low Cut filter can be adjusted by the sixth encoder. It can be turned on or off by pressing the rec
(clip) button under this encoder.
Delay can be changed byt the seventh encoder. It can be turned on or off by pressing the rec (clip)
button under this encoder.
The insert effect can be selected by turning the last encoder. Insert position of this effect can be
switched by pressing down on this encoder button. The effect can be turned on or off by pressing
the rec (clip) button under this encoder.
Gate
In gate mode, the channel selection is the same as explained above in config mode.
The treshold is adjusted by turning the second encoder button.
The gate is activated or deactivated by pressing the rec (clip) under this encoder
With the second encoder you can change the range. The rec (clip) button under it lets you change
the mode.
The next three encoders let you change the attac , hold and release.
The seventh encoder selects the sidechain filter type. Press and hold this button while turning to
select the source channel for this filter. The button under this encoder activates or deactivates the
sidechain filter.
The last encoder selects the frequency of the filter. The rec (clip) button under this encoder is the
solo button for the filter.
Q
In eq mode, the channel selection is the same as explained above in config mode.
If an input channel is selected, the last 4 encoder nobs are used to set the gain of the respective eq
band (or parameter actually). Press and turn the encoder nob to change the frequency.
The second encoder nob selects the mode of the last 4 encoder nobs. In mode 1/2 they act as
described above. In mode 2/2 turn the last 4 encoders to change the bandwith (quality factor) of the
band. Press and turn the encoder nob to change the type of equalizer band.
Press the rec (clip) button under the second encoder to turn the eq on or off
The third encoder selects teh frequency of teh high pass filter. The rec (clip) button under it turns
the high-pass filter on or off
If a bus is selected, the last 6 encoder nobs are used for the 6 bands of the equaliser. There is no
high-pass filter on the busses.
Dyn
{to be completed }
Main
{to be completed }
BUS Sends
he bus sends page is split into two pages. Since there are 16 busses, but there are only 8 encoder
knobs. When you press the bus sends button once, the encoder knobs correspond to the first 8
busses as shown on the scribble trips. he bus sends button flashes to indicate this as well. When
you press teh bus sends button a second time, the encoder knobs now control the remaining 8
busses. his is also indicated on the scribble strips. he bus send button is now solid lit to indicate
this.
Fader bank layout
To the left of the faders in the X32-Edit app, there are 9 buttons. With these buttone you can select
different fader ban layouts. Those buttons can be operated from the X-Touch by pressing the up
and down buttons just left of the big scrollweel. If you use these buttons, the channels on the X-
Touch will also show the new faderban layout. It is important to note here, that if you clic on
those buttons on the screen, the X-Touch doesn't now this and thus will not show the new
faderban layout. Therefore ma e a habit of allways using the up and down buttons.
The faderban layouts are all customisable (except for the last ban , which is the Dca spill). The X-
Touch can also follow this custom lauout, but there is one catch. In order for the X-Touch to follow
your new layout, you must close X32-Edit application and start it again. And also stop the
X32cntrl and restart it again. After that, the X-Touch will exactly match the channels on the
screen. This way you can mix input channels, busses, effects returns etc. together on one fader ban .
Best practice here is start the X32-Edit program first, do your planning of the channel use, edit all
the faderban s to your whish and then close the X32-Edit program. Then restart it and start
X32cntrl.
The last layout button is for the Dca spill. It is basically a fader ban per dca, that lets you control
the channels currently assigned to that specific dca. If you select this button, by using the down
button on the X-Touch, the X-Touch will also display this fader ban . This wor s dynamically, so
you don't have to shtudown and restart X32-Edit if you change the dca settings. On this ban you
can select the 8 different dca’s by pressing the left and right button next to the big encoder wheel.
Otros manuales para X32 DIGITAL MIXER
22
Tabla de contenidos
Otros manuales de Mezclador de música de Behringer
Behringer
Behringer XENYX X1222 USB Manual de usuario
Behringer
Behringer Europower PMH880S Manual de usuario
Behringer
Behringer DIGITAL MIXER X32 PRODUCER Manual de usuario
Behringer
Behringer 121 DUAL VCF Manual de usuario
Behringer
Behringer EUROPOWER PMX2000 Manual de usuario
Behringer
Behringer XENYX QX1832USB Manual de usuario
Behringer
Behringer Europower PMP1000 Manual de usuario
Behringer
Behringer XENYX 1002B Instrucciones de montaje
Behringer
Behringer PRO MIXER DX1000 Manual de usuario
Behringer
Behringer PRO MIXER VMX1000USB Manual de usuario
Behringer
Behringer XENYX 1002B Manual de usuario
Behringer
Behringer EURODESK SX3282 Manual de usuario
Behringer
Behringer XENYX QX1002USB Manual de usuario
Behringer
Behringer POWERPLAY P16-M Manual de usuario
Behringer
Behringer DANALOG DDX3216 Manual de usuario
Behringer
Behringer SUPER PHASE SHIFTER SP400 Manual de usuario
Behringer
Behringer B-Control Deejay BCD3000 Manual de usuario
Behringer
Behringer X32 DIGITAL MIXER Manual de usuario
Behringer
Behringer B-CONTROL DEEJAY BCD2000 Manual de usuario
Behringer
Behringer XENYX 2222FX Manual de usuario
