Becos TS8-MS Overdrive Midi Switching Hoja de especificaciones

http://midi-overdrive-switcher.becosfx.com/

TS8-MS Quick Setup

For full product information go to http://midi-overdrive-switcher.becosfx.com/

1. Power off pedal (battery or DC power adapter) and set the Multi Function rotary HEX

switch inside to a position corresponding to the desired setup setting.

2. Push and hold the Footswitch while power on pedal and continue to hold the Footswitch

for at least 3 seconds, until visual indication of LED's confirm saving the setting.

3. Power off pedal. The setting is saved. Power on pedal and start using it.

Set the type of Bypass

Bypass Type Multi Function

Switch Position*

Visual

Indication**

Notes

Buffered Bypass

(factory default) HEX = A

Silent "soft switching" using FET transistors

placed between input and output buffers. No

sound loss even with long connection cables.

Recommended and used as factory default.

Relay True Bypass HEX = B

Mechanical switching using relays controlled

by a microcontroller. In bypass or without

power, signal goes directly from input to

output. Avoid long connection cables.

Set the switching mode of External Switching Relays

Switching Type Multi Function

Switch Position*

Visual

Indication**

Notes

Latching Switching

(factory default) HEX = 0

External Relay switching with latching. When

relays are ON, Tip-to-Ground or/and Ring-to-

Ground are shorted and mentained until OFF

command is initiated.

Momentary

Switching HEX = 1

External Relay switching is momentary ON.

Tip-to-Ground or/and Ring-to-Ground in the

External Switching 1/4TRS Connector are

shorted momentarely (100ms ON, then OFF)

for either "ON" or "OFF" relay commands.

Reset to Factory Defaults

Reset Multi Function

Switch Position*

Visual

Indication**

Notes

Factory Defaults HEX = F

Pedal settings are restored to factory defaults.

* After setting procedure is finished (power off), you may need to set the Multi Function switch to a different in operation position than

the one used for setup.

** During setup, LED blinking is continuous until power off. Steady lit LED's remain as such until power off.

Download Full Manual

http://midi-overdrive-switcher.becosfx.com/

Footswitch Action

You can use pedal footswitch to perform the following actions:

1. Change pedal state: Bypass / Overdrive / Extended (long-

push; pedal state is preserved; only External Switching

Relays are affected).

2. Switch amp channel with each pedal state - see Multi

Function switch and External Switching Relay switching

pattern Table 1.

3. Transmit MIDI Program Change with each pedal state - see

Multi Function switch.

Multi Function Switch

The Multi Function switch inside pedal has 16 positions and it is used to:

1. Set MIDI Channel for Transmit or Receive function (see: How to set pedal to transmit or receive

MIDI).

2. Assign External Switching Relays switching pattern, when pedal footswitch is used.

BYPASS EFFECT EXTENDED

MULTI FUNCTION SWITCH

MIDI Transmit = PC# 1 MIDI Transmit = PC# 2 MIDI Transmit = PC# 3

MIDI Ch.

Transmit

MIDI Ch.

Receive

External

Switching

Relay 1

External

Switching

Relay 2

External

Switching

Relay 1

External

Switching

Relay 2

External

Switching

Relay 1

External

Switching

Relay 2

0 16 OMNI Off Off Off Off On On

1 1 1 Off Off On Off Off On

2 2 2 Off Off Off On On On

3 3 3 Off Off On On On Off

4 4 4 On Off Off Off On On

5 5 5 On Off On Off On On

6 6 6 On Off Off On Off Off

7 7 7 On Off On On Off On

8 8 8 Off On Off Off On Off

9 9 9 Off On On Off On On

A 10 10 Off On Off On On Off

B 11 11 Off On On On Off Off

C 12 12 On On Off Off Off On

D 13 13 On On On Off Off Off

E 14 14 On On Off On On Off

F 15 15 On On On On Off On

Table 1 - Footswitch Action - External Switching Relays switching pattern and MIDI Channel select

based on Multi Function switch position set (and MIDI Socket used on circuit board: TX or RX)

Note: External Switching Relay 1 = Tip-To-Ground, External Switching Relay 2 = Ring-To-Ground

http://midi-overdrive-switcher.becosfx.com/

Set TS8-MS pedal to transmit or receive MIDI

Inside the pedal there are two small 4-pin sockets: one socket is for MIDI Receive function (factory default) and another

for MIDI Transmit function. The external 5-pin MIDI connector is connected to the circuit board on one socket or the

other, through a 4-wire jumper cable. Only one function can be used at a time.

MIDI Control - Program Change

TS8-MS pedal is pre-programmed to respond to the following Program Change numbers:

Program Change

Number

Bypass / Effect

Relay

Switching

Relay 1

Tip-To-Gnd

Switching

Relay 2

Ring-To-Gnd

#50 Bypass Off Off

#51 Bypass On On

#52 Bypass Off On

#53 Bypass On Off

#54 Effect Off Off

#55 Effect On On

#56 Effect Off On

#57 Effect On Off

Table 2 - MIDI Program Change switching options in TS8-MS

MIDI Control - Control Change

TS8-MS pedal is pre-programmed to respond to the following MIDI Control Change numbers:

Relay/LED

OFF

Relay/LED

Control

Change

Number

Relays Controlled

CC Value CC Value

80 Bypass

81 R1

82 R2

83 Bypass, R1, R2

84 Bypass, R1

85 R1, R2

86 Bypass, R2

0-63 64-127

Table 3 - MIDI Control Change switching options in TS8-MS

Note: Bypass = Effect/Bypass Relay. R1 = External Switching Relay 1 (Tip-to-Ground). R2 = External Switching Relay 2

(Ring-to-Ground).

http://midi-overdrive-switcher.becosfx.com/

How to use TS8-MS

TS8-MS is an analog overdrive pedal which can be enabled with midi, is a MIDI switcher and a MIDI transmitter in a

box. All of the above function simultaneously in either setup mode. Here are several examples of how you can use it:

Footswitch Action - use TS8-MS as analog overdrive and amp channel switcher

Footswitch Action - use TS8-MS as analog overdrive, switch amplifier channels

and transmit MIDI Program Change messages, all at once

External MIDI Control - switch TS8-MS analog overdrive and amp channels with an external MIDI Controller

Otros manuales para TS8-MS Overdrive Midi Switching

Tabla de contenidos

Otros manuales de Pedal de música de Becos

Becos

Becos CIQ-2 COMPIQ MINI PRO COMPRESSOR Manual de usuario

Becos

Becos CIQT-1 COMPIQ TWAIN Manual de usuario

Becos

Becos CIQ-1 COMPIQ MINI ONE PRO Manual de usuario

Becos

Becos COMPIQ TWAIN PRO COMPRESSOR Manual de usuario

Becos

Becos COMPIQ PRO STELLA COMPRESSOR Manual de usuario

Becos

Becos CIQ-2 CompIQ MINI Pro Compressor Manual de usuario

Becos

Becos CIQ-5 COMPIQ PRO Manual de usuario

Becos

Becos COMPIQ MINI ONE Manual de usuario

Becos

Becos CIQ-2 COMPIQ MINI PRO Manual de usuario

Becos

Becos CIQ-2 COMPIQ MINI PRO Manual de usuario

Becos

Becos ZIFFER JORDAN ZIFF SIGNATURE Manual de usuario

Manuales populares de Pedal de música de otras marcas

Behringer

Behringer ULTRA WAH UW300 Manual de usuario

Whirlwind

Whirlwind oc-bass Manual de usuario

Strymon

Strymon Lex-rotary Manual de usuario

Behringer

Behringer PB600 Manual de usuario

Lexicon

Lexicon MX200 Manual de usuario

Dunlop

Dunlop Hendrix 68 Shrine Octavio Fuzz Series Manual de usuario

Matthews Effects

Matthews Effects Whaler V2 Manual de usuario

Grid 1

Grid 1 Pedal Jeanie Manual de usuario

Amptweaker

Amptweaker tightboost Manual de usuario

Ibanez

Ibanez TS-808 Tube Screamer Overdrive Pro Manual de usuario

PuzzleSounds

PuzzleSounds DR. Q ENVELOPE FILTER Manual de usuario

BYOC

BYOC Analog Chorus Manual

Dimavery

Dimavery EPVP-50 Manual de usuario

Tefi Vintage Lab

Tefi Vintage Lab GEGÈ Manual de usuario

Pro-MIDI

Pro-MIDI G25 Manual de usuario

DW 7000 Manual de usuario

FAMC

FAMC Liquid-Foot Jr. Series Manual de usuario

Dimavery

Dimavery EPOD-50 Overdrive Manual de usuario