Beckhoff CP6606-0001-0020 Manual de usuario

Installation and Operating instructions for

CP6606-0001-0020

„Economy“ Built-in Panel PC

Version: 1.1

Date: 2016-10-07

Table of contents

1Foreword 3

1.1 Notes on the Documentation 3

1.1.1 Liability Conditions 3

1.1.2 Trademarks 3

1.1.3 Patent Pending 3

1.1.4 Copyright 3

1.1.5 State at Delivery 3

1.1.6 Delivery conditions 3

1.2 Description of safety symbols 4

1.3 Basic safety measures 5

1.4 Operator’s obligation to exercise diligence 6

1.4.1 National regulations 6

1.4.2 Procedure in the event of a fault 6

1.4.3 Operator requirements 6

2Product Description 7

2.1 Product overview 7

2.2 Appropriate Use 8

2.3 Access to the connectors 8

2.4 Interfaces 9

2.4.1 Power Supply (X101) 9

2.4.2 Network connection LAN1 (X 102) 9

2.4.3 EtherCAT connection (X 103) 9

2.4.4 USB output (X 104, X 105) 9

2.4.5 Serial interface COM1 (X107) 9

2.4.6 Ground connection (Ground) 9

2.5 Access to the battery and the plug-in card slot 10

2.6 Status-LEDs 10

3Installation 11

3.1 Transport and Unpacking 11

3.1.1 Transport 11

3.1.2 Unpacking 11

3.2 Installation in the control cabinet 12

3.2.1 Preparation of the control cabinet 12

3.2.2 Installation in a control cabinet wall 12

3.2.3 Mounting of the Panel PC 13

3.3 Wall installation with wall mounting frame (optional) 14

CP6606-0001-0020 1

Table of contents

3.3.1 Mounting the wall mounting frame 14

3.3.2 Cut out dimension 15

3.3.3 Plastering the frame 15

3.3.4 Mounting of the Panel PC 15

3.4 Fitting the power supply cable 16

3.5 Connecting the Panel PC 17

3.5.1 Connecting cables 17

3.5.2 Earthing measures 17

4Operating Instructions 18

4.1 Switching the Panel PC on and off 18

4.1.1 Switching on 18

4.1.2 Shutting down and switching off 18

4.1.3 First switching on and driver installation 18

4.2 Operation 18

4.3 Servicing and maintenance 19

4.3.1 Cleaning 19

4.3.2 Maintenance 19

4.3.3 Replacing the battery on the motherboard 19

4.4 Emergency procedures 19

4.5 Shutting down 19

4.5.1 Disposal 19

5Troubleshooting 20

6Assembly dimensions 21

7Technical Data 22

8Appendix 23

8.1 Beckhoff Support and Service 23

8.1.1 Beckhoff branches and partner companies 23

8.1.2 Beckhoff company headquarters 23

8.2 Approvals for USA and Canada 24

8.3 FCC Approvals for the United States of America 24

8.4 FCC Approval for Canada 24

2CP6606-0001-0020

Foreword

1 Foreword

1.1 Notes on the Documentation

This description is only intended for the use of trained specialists in control and automation engineering

who are familiar with the applicable national standards. It is essential that the following notes and

explanations are followed when installing and commissioning these components.

The responsible staff must ensure that the application or use of the products described satisfy all the

requirements for safety, including all the relevant laws, regulations, guidelines and standards.

1.1.1 Liability Conditions

The documentation has been prepared with care. The products described are, however, constantly under

development. For that reason the documentation is not in every case checked for consistency with

performance data, standards or other characteristics. In the event that it contains technical or editorial

errors, we retain the right to make alterations at any time and without warning. No claims for the

modification of products that have already been supplied may be made on the basis of the data, diagrams

and descriptions in this documentation.

All pictures shown in the documentation are exemplary. Illustrated configurations can differ from standard.

1.1.2 Trademarks

Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®and XFC®are registered

trademarks of and licensed by Beckhoff Automation GmbH.

Other designations used in this publication may be trademarks whose use by third parties for their own

purposes could violate the rights of the owners.

1.1.3 Patent Pending

The EtherCAT Technology is covered, including but not limited to the following patent applications and

patents: EP1590927, EP1789857, DE102004044764, DE102007017835 with corresponding applications

or registrations in various other countries.

The TwinCAT Technology is covered, including but not limited to the following patent applications and

patents: EP0851348, US6167425 with corresponding applications or registrations in various other

countries.

1.1.4 Copyright

©Beckhoff Automation GmbH & Co. KG.

The reproduction, distribution and utilization of this document as well as the communication of its contents

to others without express authorization are prohibited. Offenders will be held liable for the payment of

1.1.5 State at Delivery

All the components are supplied in particular hardware and software configurations appropriate for the

application. Modifications to hardware or software configurations other than those described in the

documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.

1.1.6 Delivery conditions

In addition, the general delivery conditions of the company Beckhoff Automation GmbH & Co. KG apply.

CP6606-0001-0020 3

Foreword

1.2 Description of safety symbols

The following safety symbols are used in this operating manual. They are intended to alert the reader to

the associated safety instructions.

Acute risk of injury!

DANGER

If you do not adhere the safety advise adjoining this symbol, there is immediate

danger to life and health of individuals!

Risk of injury!

WARNING

If you do not adhere the safety advise adjoining this symbol, there is danger to life and

health of individuals!

Hazard to individuals!

CAUTION

If you do not adhere the safety advise adjoining this symbol, there is obvious hazard to

individuals!

Hazard to devices and environment

Attention

If you do not adhere the notice adjoining this symbol, there is obvious hazard to

materials and environment.

Note or pointer

Note

This symbol indicates information that contributes to better understanding.

4CP6606-0001-0020

Foreword

1.3 Basic safety measures

Before the Panel PC is switched off, software that is running must be properly closed.

Otherwise it is possible that data on the storage medium is lost. Please read the section Switching the

Panel PC on and off.

Switch off all parts of the equipment, then uncouple the Panel PC

Warning

Before opening the housing, and whenever the Panel PC is not being used for control

purposes (such as during functional checks after a repair), all parts of the equipment

must first be switched off, after which the Panel PC is to be disconnected from the

equipment.

Disconnect the device by unplugging the connectors on the rear side of the Panel PC.

Items of equipment that have been switched off must be secured against being switched on again.

Do not exchange any parts when under power

Warning

When components are being fitted or removed, the supply voltage must be switched

off.

Fitting work on the Panel PC can result in damage:

• if metal objects such as screws or tools fall onto operating circuit boards

• if connecting cables internal to the Panel PC are removed or inserted during

operation.

CP6606-0001-0020 5

Foreword

1.4 Operator’s obligation to exercise diligence

The operator must ensure that

• the product is only used as intended (see chapter Product Description)

• the product is in a sound condition and in working order during operation

• the product is operated, maintained and repaired only by suitably qualified and authorized

personnel

• the personnel is instructed regularly about relevant occupational safety and environmental

protection aspects, and is familiar with the operating manual and in particular the safety notes

contained herein

• the operation manual is in good condition and complete, and always available for reference at the

location of the product.

Do not open the housing of the Panel PC!

Note

For technical support contact Beckhoff Service.

1.4.1 National regulations

Depending on the type of machine and plant in which the Panel PC is used, national regulations

governing the controllers of such machines will apply, and must be observed by the operator. These

regulations cover, amongst other things, the intervals between inspections of the controller. The operator

must initiate such inspections in good time.

1.4.2 Procedure in the event of a fault

In the event of faults at the Panel PC, the list in the section Troubleshooting can be used to determine the

measures to be taken.

1.4.3 Operator requirements

Anyone who uses the Panel PC must have read these operating instructions and must be familiar with all

the functions of the software installed on the Industrial PC to which he has access.

6CP6606-0001-0020

Product Description

2 Product Description

2.1 Product overview

The compact built-in Panel PC

The built-in Panel PC CP6606-0001-0020 with Ethernet port can be used as an independent Panel PC,

remote desktop display or server terminal. The powerful 1 GHz ARM Cortex™ A8 CPU is suitable for

versatile use in PLC and Motion Control applications in small and medium-sized machines, plants or

buildings.

The Panel PC offers the following benefits:

• 7-inch TFT display, 800 x 480 WVGA

• touch screen

• aluminium front with sheet-steel rear cover

• protection class front side IP54, rear side IP20

• operating temperature 0…55 °C (0°C to +45°C with wall mounting frame)

• all connectors at the lower rear side

• 1 slot for MicroSD Flash Card, accessible from the rear side

• lithium battery of the system clock, accessible from the rear side

• pull-out clamping levers for fast installation without loose parts

• low installation depth.

CP6606-0001-0020 7

Product Description

2.2 Appropriate Use

The built-in Panel PC CP6606-0001-0020 is suitable for versatile use in PLC and Motion Control

applications in small and medium-sized machines, plants or buildings. A TFT display with touchscreen is

accommodated in a steel housing with aluminium front. The Panel PC is installed in the front of control

cabinets, for wall installation the wall mounting frame with order option C9900-M317 is necessary.

Risk of explosion!

Danger

The Panel PC must not be used where there is a risk of explosion.

2.3 Access to the connectors

The connectors of the Panel PC are located at the lower rear side of the housing.

Picture: Bottom view

8CP6606-0001-0020

Tabla de contenidos

Otros manuales de Panel táctil de Beckhoff

Beckhoff

Beckhoff CP32 -2 -0020 Series Manual de usuario

Beckhoff

Beckhoff CP22 Series Manual de usuario

Beckhoff

Beckhoff CP6600-0001-0020 Manual de usuario

Beckhoff

Beckhoff CP6201 Manual de usuario

Beckhoff

Beckhoff CP32-1600 Series Manual de usuario

Beckhoff

Beckhoff CP37 1600 Series Manual de usuario

Beckhoff

Beckhoff CP7709 Manual de usuario

Beckhoff

Beckhoff CP770 140 Series Manual de usuario

Beckhoff

Beckhoff CP37-1600 Series Manual de usuario

Beckhoff

Beckhoff CP63 Series Manual de usuario

Beckhoff

Beckhoff CPX2719 Manual de usuario

Beckhoff

Beckhoff CP27 Series Manual de usuario

Beckhoff

Beckhoff CP37-1600 Series Manual de usuario

Beckhoff

Beckhoff CP64 Series Manual de usuario

Beckhoff

Beckhoff CP65**-0060 Manual de usuario

Beckhoff

Beckhoff CP72 Series Manual de usuario

Beckhoff

Beckhoff CP77 Series Manual de usuario

Beckhoff

Beckhoff CP67 Series Manual de usuario

Beckhoff

Beckhoff CP32-2 Series Manual de usuario

Beckhoff

Beckhoff CP32-2-0020 Series Manual de usuario

Beckhoff

Beckhoff CP37 Series Manual de usuario

Beckhoff

Beckhoff CP22 Series Manual de usuario

Beckhoff

Beckhoff CP26 Series Manual de usuario

Beckhoff

Beckhoff CP71 Series Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario