BARRON specialityLED RFX Manual de usuario
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
•Installation and servicing of this equipment should be performed by qualified service personnel only.
•Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
•Do not mount near gas or electrical heaters.
•Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
•The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. Any
modification or use of non-original components will void the warranty and product liability.
•Do not use this equipment for other than intended use.
800.533.3948 •www.barronltg.com
1
40070009 REV 1 11/2014
RFX
The specialtyLED Ribbon Flex is an extremely small profile product made up of Light Emitting Diodes (LED)
mounted on a thin flexible copper strip. The wet version has a clear flexible silicon housing. Due to the construction of
the product, special care needs to be taken during the installation process in order to avoid damaging the LEDs or any
of the resistors.
INSTALLATION INSTRUCTIONS
SAFETY PRECAUTIONS:
• Do not over bend to the side, product is only bendable front to back.
• Do not cover the product unless done so with extreme caution and attention to ventilation.
• Do not apply power when tightly coiled. Maintain half inch spacing between parts.
• Do not puncture, cut, shorten or splice outside of the designated cutting marks.
• Do not route through walls, doors, windows or building structures.
• Do not mount inside cabinets, tanks or enclosures unless properly ventilated.
• Do not unroll on a rough surface or over sharp corners. This will scratch or damage the LEDs.
• When unrolling or installing do not twist, pull or kink the product.
• Do not secure with staples, nails or like means that can damage the insulated PVC housing.
• Do not install in locations where it is subject to continuous flexing.
• Do not submerge in liquid or apply near standing water.
• Do not operate in temperatures exceeding 149°F (65°C).
• Ground Fault Circuit Interrupter (GFCI) protection should be provided on all circuits when used for outside
applications.
• Do not operate on circuits that do not have proper surge suppression protection. High voltage spikes will
damage the LEDs.
• Do not operate over specified voltage, LED life degradation will be greatly increased.
INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
240070009 REV 1 11/2014
RFX
General Material/Tool Requirements:
1. Measure the installation location to determine product length. Due to circuitry, RFX has a 2” cutting increment.
2. Measure the RFX to match required installation length. Locate the closest
cutting mark. This is designated by a line between 4 copper pads. (Fig. 1)
3. Using scissors, make an even cut through product exactly on the line. If cut
off the line the product can be damaged.
NOTE: It is imperative to use a sharp cutting blade to make a straight cut.
Sharp blades will help you avoid pulling the internal circuitry while making
the cut. Stretching or pulling the product can result in damage.
4. Connect the transformer to the wire leads of the RFX in accordance with current electrical codes and the
current National Electric Code (NEC). Transformers are IP67 rated / Class 2 power supplies. Install the transformer
within 10’ of the RFX.
5. Test product to verify connections are correct.
6. Adhere product to surface. Do not push directly on LEDs as this will cause damage to LEDs.
Material needed for installation:
RFX Ribbon Flex Reel (16.4’)
RFX Transformer
RFX accessories (Optional)
Additional wire as needed for connections
Measuring tape
Scissors
Part Number - 12 volt
XFMR-12-20
XFMR-12-35
XFMR-12-60
XFMR-12-150
XFMR-DIM-12-20
XFMR-DIM-12-40
XFMR-DIM-12-60
XFMR-DIM-12-96
XFMR-DIM-12-120
RFX-*-12V (2.25W/Ft)
7.1’
12.44’
21.33’
50.00’ MAX
7.10’
14.22
21.33’
34.13’
42.66’
RFX-*-12V-5050 (5.56W/Ft)
2.87’
5.04’
8.63’
21.58’
2.87’
5.75’
8.63’
13.80’
16.4’
Part Number - 24 volt
XFMR-12-20
XFMR-12-35
XFMR-12-60
XFMR-12-150
XFMR-DIM-12-20
XFMR-DIM-12-40
XFMR-DIM-12-60
XFMR-DIM-12-96
RFX-*-24V (2.25W/Ft)
7.1’
12.44’
21.33’
50.00’ MAX
7.10’
14.22
21.33’
34.13’
RFX-*-24V-5050 (5.56W/Ft)
2.87’
5.04’
8.63’
21.58’
2.87’
5.75’
8.63’
13.80’
Fig.1 Cut Line Copper Pads
INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
340070009 REV 1 11/2014
RFX
ACCESSIORIES
• RFX-CSS-XXX is designed to join (2) cut sections together. (Fig. 2)
• RFX-CSS-FLEX-XXX is designed to join (2) cut sections together
with 2” wire spacing allowing the RFX to bend or turn corners. (Fig. 3)
• RFX-CSP-XXX is designed to provide wire leads to a cut section of
RFX, to be used to assist with connection to the transformer. (Fig. 4)
NOTE: When Connecting RFX accessories attention to polarity is
require.
• When connecting lengths together keep all negatives (-) on
one side and all positives (+) on the other. Failure to do so will
leave a section non-working. (Fig. 5)
• Peel the silicon sleeve back approximately 1/8” and slide the
tape under the connector terminals, aligning the copper dots
with the terminal prongs. Snap cover down to secure the RFX
in place. (Fig. 6)
TROUBLE SHOOTING
Product will not light
• Verify that there is power to the receptacle feeding the product.
• Check the GFCI and see if it is tripped.
• Check the transformer and make sure it has power.
• Verify product porlarity is correct.
Product does not light for the first 8”- 30”
• Product was cut incorrectly. It will be necessary to re-cut the product
at the correct designated location and reassembled.
Product has a dark section in the run.
• The indicates the product was pulled, twisted, kinked and the interior
circuitry was damaged.
• It will be necessary to cut new product or cout out the damaged
section and splice a new piece in its place.
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de iluminación de BARRON
BARRON
BARRON EXITRONIX ILX Series Manual de usuario
BARRON
BARRON EXITRONIX SCL Series Manual de usuario
BARRON
BARRON Exitronix 900E Series Manual de usuario
BARRON
BARRON Exitronix NFT Series Manual de usuario
BARRON
BARRON EXITRONIX LL30 Series Manual de usuario
BARRON
BARRON Exitronix SCL Series Manual de usuario
BARRON
BARRON specialtyLED FTK Manual de usuario
BARRON
BARRON Growlite GRM Manual de usuario
BARRON
BARRON Speciality LED FBTCJ-24V Manual de usuario
BARRON
BARRON Growlite GLB-315-A-120/277 Manual de usuario
BARRON
BARRON EXITRONIX VLEDC Series Manual de usuario
BARRON
BARRON EXITRONIX LED-51 Series Manual de usuario
BARRON
BARRON Exitronix VEX-8 NEMA Manual de usuario
BARRON
BARRON EXITRONIX 400WX Series Manual de usuario
BARRON
BARRON Exitronix CRL Series Manual de usuario
BARRON
BARRON TRACE-LITE AXL2 Manual de usuario
BARRON
BARRON TRACE-LITE TL101 Manual de usuario
BARRON
BARRON Trace-Lite AXL2 Manual de usuario
BARRON
BARRON Exitronix NFT Series Manual de usuario
BARRON
BARRON TRACE-LITE RHL-ACR Manual de usuario
Manuales populares de Equipo de iluminación de otras marcas
Qazqa
Qazqa Suplux SL 3 Black 103062 Manual de usuario
Commercial Electric
Commercial Electric 54568141 Manual de usuario
CREE LIGHTING
CREE LIGHTING 304 Series Manual de usuario
Goobay
Goobay 49867 Manual de usuario
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manual de usuario
Alkalite
Alkalite Krypton KT-81 Manual de usuario
