Baroness LM2700 Manual

Technical Information Leaflet

TIL: 002

LM2700 Blade Adjustment

BARONESS LM2700 BLADE/CUT ADJUSTMENT

Before attempting to adjust the blades in order to put the machine ‘on cut’ please make sure that:

Finally, before commencing adjustment it is very important to make sure that the cutting units are

clean, especially behind the cutting cylinder between the bottom blade carrier and the cutting

cylinder. If there is build up on top of this blade carrier then this can restrict the cutting cylinder from

lowering onto the bottom blade. If necessary open up the rear grass deflector and clean the area.

The rear cutting cylinder pivot pins

must be free rotating and that this

bolt/nut is not over-tightened or

seized due to corrosion.

If it is seized: remove the bolt and

clean all surfaces (bolt and drilling)

with emery cloth. Then coat the bolt

in an anti-seize compound (Copper

Slip etc) before reinserting the bolt.

Do not tighten the nut tight. Pinch it

up and then slacken it off just a little

in order to allow the bolt to rotate.

Make sure that this spring is

sufficiently tensioned but without it

being ‘coil bound’ through over

tightened. There must be some

visible gap between each spring coil.

To adjust the spring tension, rotate

this spring pressure screw. Rotate it

anti-clockwise to add tension and

clockwise to decrease tension.

Make sure that this bolt is free

rotating and not clamping the

aluminium casting to the mower

frame. To adjust this bolt correctly,

tighten it fully and then slacken it off

a little until it rotates.

Adjusting Blade Contact

Important: Baroness blades are designed to cut with minimal contact. Never adjust them so that

they are in anything more than very light contact as this will cause friction, heat and wear to the

blades.

Whilst other manufacturers run their blades with hard contact, they are made from a softer material

which is not as durable as the Baroness. If the Baroness blades are adjusted correctly then they will

last up to 5 times longer between regrinding than other makes of blades.

To adjust the contact between cutting cylinder

and bottom blade adjust the nut.

Turning it anti-clockwise will lower the cutting

cylinder onto the bottom blade and therefore

increase contact.

Turning clockwise will raise the cutting cylinder

away from the bottom blade and decrease

contact.

To adjust blade contact you do not need to

slacken any other nuts or bolts. When you

finish adjustments do not tighten this or any

other nut. The only nut that you need to turn

during this process is the top adjustment nut.

To check that the blades are cutting

correctly use a strip of paper (as

shown).

With the strip of paper held square to

the bottom blade rotate the cutting

cylinder and see if the blades will cut

the paper. Never rotate the cutting

cylinder using your hand as the

blades are very sharp and can cause

serious injury. Use a short wooden

pole (small length of broom handle

etc) to rotate the cylinder.

If the paper is not cut you will need to lower the

cutting cylinder in order to increase blade

contact.

To do this, rotate the cylinder adjustment nut

anti-clockwise as shown.

There are two cylinder adjustment nuts, one

either side of each unit. Initially make sure you

adjust both of them by the same amount at the

same time in order to keep the cylinder parallel

to the bottom blade.

Only ever adjust them by small amounts at any

one time.

Check the cut again by using a strip of paper as

previously explained. Once again please

remember to never put your hand into the

cutting cylinder.

If the paper is still not cut correctly repeat the

above process of lowering the cutting cylinder

until the paper does cut.

If one side cuts paper but the other side does

not, lower the cutting cylinder further but only

on the side that it is not cutting.

If you are unable to achieve an acceptable cut with just a light contact by performing the above

adjustments then the blades have become a little blunt and will need back-lapping.

Once the blade is cutting paper on both sides

you need to check that you do not have

excessive blade contact.

To do this you need to use another strip of paper

but this time hold it flat along the surface of the

bottom blade as shown.

When you rotate the cutting cylinder the paper

should not be cut but should just leave an

indentation line in it. If it does this it is set ok. If

it cuts the paper then the contact is too great

and the cutting cylinder will need to be raised by

rotating the adjusting nuts clockwise.

Repeat these exercises until the paper is cut

across the full width of the unit when held

square to the bottom blade, but just leaves an

indentation line in the paper when it is held flat

along the bottom blade.

Once this is achieved the blades are correctly

adjusted.

Otros manuales para LM2700

Otros manuales de Cortacésped de Baroness

Baroness

Baroness LM180E Manual de operación

Baroness

Baroness LM18GB Manual de operación

Baroness

Baroness LM56GA(GAF) Manual de usuario

Baroness

Baroness LM531 Manual de operación

Baroness

Baroness GM2810 Manual de usuario

Baroness

Baroness LM56GC Manual de operación

Baroness

Baroness SP160EB Manual de operación

Baroness

Baroness LM56 Series Manual

Baroness

Baroness LM331 Manual de operación

Baroness

Baroness LM331 Manual de operación

Baroness

Baroness LM2700 Manual de operación

Baroness

Baroness LM54GB Manual de usuario

Baroness

Baroness SUPER MOWER LM180B Manual de usuario

Baroness

Baroness LM101 Manual de operación

Baroness

Baroness LM101 Manual de operación

Baroness

Baroness GM2800 Manual

Baroness

Baroness LM315GC Manual de operación

Baroness

Baroness LM315GC Manual de operación

Baroness

Baroness HMC172E Manual de operación

Baroness

Baroness LM285 Manual de operación

Baroness

Baroness LM315GC Manual

Baroness

Baroness LM315GC Manual

Baroness

Baroness GM1700 Manual de usuario

Baroness

Baroness LM3210A Manual de operación

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario