Baroness GM2800 Manual

Technical Information Leaflet

TIL: 017

GM2800

Height of Cut Adjustment

Preparation

Height of Cut Range

It is much easier to adjust the two

rear units by swinging them out. In

order to make this easier ensure

that the removable pin is kept clean

and greased. Periodic wire brushing

of this pin prior to greasing will ease

the removal of these pins. You will

also find it easier to remove the pins

and swing out the rear units if the

machine is parked level ground.

The Baroness GM2800 has four

height of cut ranges as indicated on

the decal which is located to the left

of the operators seat. Each range is

selected by changing the height

adjustment brackets . The position

of the bracket retaining bolts

stipulates the range selection as

indicated at the top of the decal.

For example, the column shown

second from the left will allow

heights of cuts from 30mm to

66mm. This is selected by lining up

the bolt holes ‘top right and middle

left’, as indicated by the solid white

dots which signifies bolt positions.

This second column range is the

most popular range for most

applications and is the default

setting of a new machine.

Adjusting the height of cut range

Height of cut Adjustment Bracket

Height of cut adjustment bracket

retaining bolts. This photograph

shows the bracket set in the default

position with the bolts located ‘top

right and middle left’.

Loosen all three height adjustment

shim retaining nuts. It is important

to loosen all three nuts at once and

not to try and adjust one bracket at

a time. Trying to adjust one bracket

at a time will make the task very

difficult as this will have the effect of

trying to twist the deck.

Remove all six of the shims from

above and below the bracket.

Again it is important to do this to

all three positions at once and not

to try doing one adjuster at a time.

This photograph shows all of the

shims removed from above and

below the bracket. This should be

done on all three units before

proceeding.

All three adjusting brackets can now

be moved to their new position.

This can be done one bracket at a

time.

Support the deck underneath the

bracket to be moved using a

suitable item such as a mallet as

shown.

Remove the two bracket retaining

bolts.

With the bolts removed manoeuvre

the bracket up or down until the

desired holes are aligned as

stipulated by the height setting

decal.

With the desired holes lined up, refit

the retaining bolts. Repeat this

exercise for all three brackets.

Changing height of cut

First of all make sure that the height of cut range is correct as explained above.

You can now see that the bolts have been

inserted into their new position of ‘top left and

middle right’. If you refer back to the height

chart decal you will see that this now puts this

deck into the lowest range of 20 to 56mm.

To adjust the height of cut, first of

all loosen all three height

adjustment s shim retaining nuts. It

is important to loosen all three nuts

at once and not try to adjust one

bracket at a time. Trying to adjust

one bracket at a time will make the

task very difficult as it will have the

effect of trying to twist the deck.

Once all three nuts are loose,

remove shims in order to achieve

the desired pattern as stipulated on

the height range decal. If you need

to increase the height of cut you will

need to remove shims from above

the bracket and replace them below

the bracket. To decrease height,

remove them from below the

bracket and replace them above the

bracket.

Repeat this exersice for all five decks.

This photograph shows a shim that has

been removed from above the bracket

being reinserted below the bracket in order

to increase the height of cut. Repeat this

exercise for all three height adjustment

brackets before attempting to tighten the

adjuster shim retaining nuts.

Once the shims on all three adjuster points have

been moved to the desired position, tighten the

retaining nuts firmly. Do not leave them loose

as this will cause the shims to fall out during

operation. This photograph shows the height

range bolts selected to ‘top left and middle

right’ with the shims arranged ‘five below and

one above. This will give a height of cut of

50mm as shown on the height decal.

Tabla de contenidos

Otros manuales de Cortacésped de Baroness

Baroness

Baroness SP05 Manual de usuario

Baroness

Baroness LM2700 Manual de usuario

Baroness

Baroness GM2800B Manual de operación

Baroness

Baroness LM3210A Manual de operación

Baroness

Baroness LM285 Manual de operación

Baroness

Baroness LM2700 Manual de operación

Baroness

Baroness LM18G Series Manual de usuario

Baroness

Baroness GM2810A Manual de operación

Baroness

Baroness GM1700 Manual de usuario

Baroness

Baroness Green mower LM56GA Manual de operación

Baroness

Baroness LM2400 Manual de operación

Baroness

Baroness LM311 Manual de operación

Baroness

Baroness LM66GC Manual de operación

Baroness

Baroness LM56G Manual de usuario

Baroness

Baroness LM281 Manual de operación

Baroness

Baroness LM54GA-R Manual de usuario

Baroness

Baroness GM2810A Manual de operación

Baroness

Baroness SUPER MOWER LM180B Manual de usuario

Baroness

Baroness LM180C Manual de operación

Baroness

Baroness LM2700 Manual de operación

Baroness

Baroness LM315GC Guía de configuración

Baroness

Baroness SP160EB Manual de operación

Baroness

Baroness LM531 Manual de operación

Baroness

Baroness LM315GC Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario