Baroness LM56 Series Manual

Technical Information Leaflet

TIL: 016

LM56/66

Setting the Groomer Height

BARONESS PEDESTRIAN MOWERS GROOMER ADJUSTMENT

The setting bar for the Baroness LM56/66 range of mowers has two adjusting screws which

are used as follows:

This setting bar needs to be set as follows:

Groomer height setting screw. If no groomer

is fitted then this screw is not used.

Height of Cut Setting Screw

This end of this screw (as shown) needs to

be adjusted so that it measures the same

distance as the desired groomer setting.

This screw needs to be adjusted so that the

distance between the setting bar and the underside

of the head of the screw (as shown) is adjusted so

that it measures the same distance as the desired

height of cut.

Before you can adjust the groomer you will need to make sure that the height of cut is set

correctly.

With the height of cut already set, fit the

setting bar to the machine as shown so

that the underside of the head of the

height of cut adjusting screw is sitting on

the cutting surface of the bottom blade

and that ends of the setting bar are

resting up against the rear and front

rollers.

With the groomer height already set

on the setting bar as previously

shown, check the distance between

the tips of the groomer blades and

the setting bar adjusting screw as

shown.

In this photograph the groomer is

set too high as there is a gap

between the tip of the blade and

the setting screw.

To adjuster the groomer height you will

firstly need to slacken the adjustment

locking nuts as shown.

Once they are loose, nip them up finger

tight in order to remove excess play but

to still allow the adjustment to take

place.

Repeat this on both sides of the

machine.

Next, loosen the two adjuster nuts which

are locked together by holding the

bottom one fixed whilst rotating the top

one anti-clockwise. The top nut should

then come loose allowing both nuts to be

rotated.

Repeat this on both sides of the machine.

Loosen the top not by twisting it

anticlockwise, and moving it away

from the bottom adjuster nut.

Then twist the bottom adjuster nut

anti-clockwise. This should have the

effect of lowering the groomer.

If it does not, loosen the locking nut a

little more.

Rotate the lower adjusting nuts on both

sides of the groomer until the tips of the

groomer blades are just touching the

end of the setting bar adjuster bolt.

Rotate this nut clockwise to increase the

gap and anti-clockwise to reduce the

gap.

When the tips of the groomer blades

are just touching the adjuster bolt on

both sides then the groomer is correctly

set.

NOTE: Adjust all attachments (de-thatcher and brush) in the same way.

Tighten the groomer height locking nuts

on both sides of the machine.

Re-check the groomer height setting and

if necessary re-adjust.

Once the groomer height is locked off

and checked to be correct you will

then need to lock off the groomer

adjuster nuts.

Do this by holding the bottom nut firm

whilst tightening the top nut against it

by turning it in a clockwise direction.

The act of nipping the two nuts

together will lock them so that they

do not work loose during operation.

The groomer height is now set.

Otros manuales para LM56 Series

Este manual sirve para los siguientes modelos

Otros manuales de Cortacésped de Baroness

Baroness

Baroness LM180C Manual de operación

Baroness

Baroness LM2700 Manual de operación

Baroness

Baroness SP05A Manual de operación

Baroness

Baroness LM331 Manual de operación

Baroness

Baroness LM551B Manual de operación

Baroness

Baroness HMC1560 Manual de operación

Baroness

Baroness Green mower LM56GA Manual de operación

Baroness

Baroness LM56G Manual de usuario

Baroness

Baroness LM281 Manual de operación

Baroness

Baroness LM551 Manual de operación

Baroness

Baroness SP160EB Manual de operación

Baroness

Baroness LM315GC Manual de operación

Baroness

Baroness GM2800B Manual de operación

Baroness

Baroness LM101 Manual de operación

Baroness

Baroness LM180C Manual de operación

Baroness

Baroness GM1700 Manual de operación

Baroness

Baroness LM285 Manual de operación

Baroness

Baroness LM56 Series Manual

Baroness

Baroness LM551 Manual de operación

Baroness

Baroness LM315GC Manual

Baroness

Baroness LM551 Manual de usuario

Baroness

Baroness LM56GA(GAF) Manual de usuario

Baroness

Baroness LM101 Manual de operación

Baroness

Baroness LM2700 Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Toro

Toro Groundsmaster 3505-D Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Toro

Toro 74806 Manual de usuario