B&G Network Series Manual de usuario
610-HB-0503-05 1
CONTENTS.....................................................................1
GENERAL INTRODUCTION TO B&G NETWORK.........2
INTRODUCTION TO NETWORK QUAD.........................3
EXAMPLE SYSTEMS USING NETWORK QUAD...........4
SELECTING THE DISPLAY MODE................................5
USING THE SPEED KEY................................................6
CALIBRATION AND OPERATING PARAMETERS........7
SETTING THE DISPLAY DAMPING...............................8
SETTING THE SPEED AND LOG UNITS.......................9
SPEED AND LOG CALIBRATION................................10
1 - MANUAL CALIBRATION - CAL................................11
2 - MANUAL CALIBRATION - LOG CAL .......................12
3 - AUTOMATIC CALIBRATION - AUTO CAL...............13
RESETTING THE DEAD RECKONED DISTANCE .......15
USING THE DEPTH KEY..............................................16
THE DEPTH DATUM - CAL...........................................17
SETTING THE DEPTH DATUM ....................................18
SETTING THE DEPTH UNITS ......................................19
DEPTH ALARMS ..........................................................20
SHALLOW ALARM
ENABLING/DISABLING THE SHALLOW ALARM.........21
ADJUSTING THE SHALLOW ALARM VALUE..............21
DEEP ALARM
ENABLING/DISABLING THE DEEP ALARM.................22
ADJUSTING THE DEEP ALARM VALUE......................22
ANCHOR ALARM
USING THE ANCHOR ALARM......................................23
ENABLING/DISABLING THE ANCHOR ALARM ...........24
ADJUSTING THE ANCHOR ALARM SHALLOW LIMIT.25
ADJUSTING THE ANCHOR ALARM DEEP LIMIT.........25
USING THE TIMER/TEMP KEY ....................................26
RESETTING THE TRIP LOG.........................................27
SETTING THE TIMERS AND LAP TIMER.....................28
SETTING THE TEMPERATURE UNITS........................29
CALIBRATING THE TEMPERATURE SENSOR............30
USING THE LIGHTS KEY .............................................31
NETWORK ALARMS.....................................................32
FAULT AND ERROR MESSAGES.................................33
INSTALLATION.............................................................34
SITING THE UNIT..........................................................34
MOUNTING THE UNIT ..................................................34
SPECIFICATION............................................................36
CONTENTS
2
The B&G Network range of instruments is designed to be
used as individual units or connected together to form an
integrated navigational system. A single network cable is
used to carry data and power between units. The latest
technology and screened cables throughout the Network
System ensure the ultimate protection from interference
between units and other systems. All Network instruments
can be linked to Network PILOT, Network CHART, Network
GPS or Network LORAN receivers or via NMEA 0183 (v1.5)
to other navigational equipment.
INSTRUMENTS
Network SPEED
Network DEPTH
Network QUAD
Network WIND
Network TACK
Network DATA
NAVIGATIONAL AIDS
Network NAV
Network GPS
Network LORAN
LCD CHART
AUTOPILOTS
Network PILOT
The Network QUAD unit measures and displays Speed,
Depth, Log, Timer and Sea Temperature information on a
large back-lit Liquid Crystal Display (LCD). The LCD is
divided into three display areas. The top area permanently
shows speed information, the centre area is selectable and
shows Log, timer, sea temperature and depth alarm
information, and the bottom area permanently shows depth
information.
The five keys allow selection of the displayed information
and setting of the units mode, calibration factors and
operating parameters.
It can operate as the main Network QUAD unit either alone
or as part of an Integrated Network Instrument System
taking inputs directly from Speed and Depth Sensors which
plug into the sockets at the rear of the display, or as a
repeater (by selecting repeater mode) of information
received via the two Network cable tails.
The Network QUAD REPEATER (not a Network QUAD in
repeater mode) does not have Speed and Depth Sensor
sockets, so it only receives data via the system network. It
offers identical facilities to a Network QUAD main unit but
can only ever be used as a repeater.
GENERAL INTRODUCTION TO B&G NETWORK INTRODUCTION TO NETWORK QUAD
3
The Network QUAD unit has three adjustable alarms:
1. Shallow water alarm
2. Deep water alarm
3. Anchor alarm
An internal alarm buzzer will sound when an alarm condition
is met and the display will flash. The alarm is broadcast to all
other Network Instruments in an integrated system, they will
also sound their alarms and flash their displays (except
Network WIND and Network TACK).
The Network QUAD unit is NOT able to transmit NMEA 0183
(v1.5), however, the Network QUAD REPEATER unit is able
to transmit NMEA data via the system network cables to
other Network units and connect to an NMEA device e.g. a
position fixer, with a special NMEA output cable.
IMPORTANT NOTE
Your Network QUAD unit must be set-up and calibrated
correctly before it is used as part of a navigational system.
INTRODUCTION TO NETWORK QUAD CONT'D NETWORK QUAD DISPLAY UNIT
4
Only one Network QUAD unit should have speed and depth
sensors connected to it and set to transducer mode. Up to
three more Network QUAD (set to repeater mode) or QUAD
REPEATER units can be connected on to the system
network.
When in repeater mode, if the data is not
being received from the system network, the
display will show OFF when a key is
pressed.
If the Network QUAD unit losses valid depth data, due either
the actual depth being outside the working range, or to
extreme turbulence in the water the LCD will show 3
"floating" bars. This shows that the unit is attempting to
calculate the depth and is still functioning.
EXAMPLES SYSTEMS USING NETWORK QUAD
Repeater Mode Repeater unitRepeater Mode
Main unit QUAD QUAD QUADQUAD
Sensor
Depth Speed
Sensor
SPEED
DEPTH
QUAD WIND QUAD PILOT
Depth
Sensor Speed
Sensor
5
The Network QUAD unit has two operating modes. The
correct mode must be selected for your Network system to
operate properly.
tYPEt Transducer mode, the unit uses and displays
speed and depth data from sensors
connected directly into the display unit.
tYPEr Repeater mode, the unit operates as a
repeater using data from the system network.
Press TIMER key
to display stored
log.
Press SETUP key
to display the
current mode.
Press ENTER
key if the mode
needs to be
changed.
Use !or "to
change mode. Press ENTER to
store the new
mode in memory.
Press TIMER to
complete the
change.
SELECTING THE DISPLAY MODE
6
Boat speed information is permanently displayed in the top
area of the LCD.
Press the SPEED key to cycle through the following
options:
SPEED Current boat speed in Knots, can also be
displayed in MPH.
AVERAGE Average boat speed since the last reset of
SPEED the trip log.
MAX Maximum boat speed since the last reset
SPEED of the trip log.
USING THE SPEED KEY
7
When current boat speed is displayed, press the SETUP key
to cycle through the following options:
DAMPING The response time of the display to
changes in boat speed.
SPEED KNOT
The boat speed can be displayed in Knots
or MPH. This setting also changes the log
units to Nautical or Statute Miles.
CAL Manual boat speed and log calibration.
LOG Manual boat speed and log calibration.
CAL
AUTO CAL Automatic boat speed and log
calibration.
dr Reset Dead Reckoned Distance.
When in SETUP mode:
The SPEED key becomes the UP key !
The LOG key becomes the DOWN key "
The LIGHTS key becomes the ENTER key.
The procedures for using the SETUP options are on the
following pages.
CALIBRATION AND OPERATING PARAMETERS
8
Damping allows the response time of the displayed speed
value to be slowed down if it is to jumpy in rough weather, or
to sped it up when the conditions are calm. The damping
works by averaging the values over a set time period; the
longer the time period the smoother the readings, however
the longer it takes to see a change. Similarly the shorter it is
the jumpier the readings, but the faster the response.
The Network QUAD unit has a factory set value of 5, this
can be adjusted in the range 1 to 64, each step is
approximately one second.
Press SPEED
key to display
current boat
speed.
Press SETUP key
once to display
the damping
value.
Press ENTER
key if the value is
to be changed.
Use !or "to
change the value. Press ENTER
key to memorise
the change.
Press SPEED
key to display
current boat
speed.
SETTING THE DISPLAY DAMPING
9
The Network QUAD can be set to display boat speed in
Knots or MPH.
If boat speed is in Knots then log is in Nautical Miles.
If boat speed is in MPH then log is in Statute Miles.
Press SPEED
key to display
current boat
speed.
Press SETUP key
twice. The speed
digits will blank.
Press ENTER
key if the units
are to be
changed.
Use !or "to
change the units. Press ENTER
key to memorise
the change.
Press SPEED
key to display
current boat
speed.
SETTING THE SPEED AND LOG UNITS
10
Before Network QUAD is used for navigation the boat speed
and log have to be calibrated to ensure accuracy for your
installation and the boats hull characteristics.
Three methods are available with the Network QUAD unit,
two manual adjustments and one automatic:
MANUAL CALIBRATION
1. CAL The displayed boat speed value is corrected
manually to read a known measured speed.
2. LOG The units calibration figure (Hz/Knot) is
CAL manually adjusted to correct log and speed
inaccuracy.
AUTOMATIC CALIBRATION
3. AUTO CAL The unit automatically calibrates and
corrects the boat speed and log.
Use the one of the methods overleaf to calibrate your
instrument. It is recommended that AUTO CAL is used as
this method will ensure the most accurate calibration of your
Network QUAD unit.
SPEED AND LOG CALIBRATION
Otros manuales para Network Series
2
Este manual sirve para los siguientes modelos
10
Tabla de contenidos
Otros manuales de Equipos marinos de B&G
B&G
B&G PTT Manual de usuario
B&G
B&G H5000 Pilot Manual de usuario
B&G
B&G H5000 Pilot Manual de usuario
B&G
B&G HERCULES Manual de usuario
B&G
B&G Zeus3 Glass Helm Manual de usuario
B&G
B&G Triton Display Manual de usuario
B&G
B&G Zeus3 Glass Helm Manual de usuario
B&G
B&G Vulcan R Series Manual de usuario
B&G
B&G Zeus2 series Manual de usuario
B&G
B&G Network Series Manual de usuario
B&G
B&G RAM T3 Manual de usuario
B&G
B&G h1000 pilot Manual de usuario
B&G
B&G Zeus 3S Manual de usuario
B&G
B&G H5000 Pilot Manual de usuario
B&G
B&G Triton Edge Manual de usuario
B&G
B&G Triton Edge Manual de usuario
B&G
B&G h3000 Manual de usuario
B&G
B&G HB-1000I Manual de usuario
B&G
B&G h1000 pilot Manual de usuario
B&G
B&G H5000 Pilot Manual de uso y cuidado
Manuales populares de Equipos marinos de otras marcas
Clarion
Clarion GR10BT Manual de reparación
Raymarine
Raymarine Maxiview ST80 Guía del usuario
GUIDANCE MARINE
GUIDANCE MARINE 20- Series Instrucciones de montaje
Raymarine
Raymarine ST60 Tridata Guía del usuario
olympia electronics
olympia electronics ΒS-531/1/MAR Manual de usuario
Sonic
Sonic 2024 Manual de usuario