Badger Meter Orion 64989-002 Manual de usuario

Installation &

Operation Manual

BadgerMeter,Inc.

ORI-IOM-47

P/N 62014 Rev. 1

6-07

Badger®ORION®

Automated Meter

Reading System

ORION Transmitter for

American

Commercial Meters

IMPORTANT: This manual contains important warnings and information.

READ AND KEEP FOR REFERENCE.

After Installation of

ORION Transmitter

After Installation of

ORION Transmitter

Before Installation

with Red Security Seals

Before Installation

with Wire Seal Security Screw

Disclaimer

The user/purchaser is expected to read and understand the information provided in this manual,

follow any listed Safety Precautions and Instructions and keep this manual with the equipment for

future reference.

Misuse, mishandling and/or inadequate maintenance may impair performance and/or compromise

safety.

Questions or Service Assistance

If you have questions regarding the product or this document contact:

Badger Meter, Inc.

P.O. Box 245036

Milwaukee, WI 53224-9536

Telephone: (414) 355-0400, (800) 876-3837

Fax: (888) 371-5982

On the Web: www.badgermeter.com

or call your local Badger Meter representative.

Product Identification Information

Record the product identification numbers from the nameplate.

Transmitter

Model Number _ ______

Serial Number _____________

Tag Number _______________

Table of Contents

Disclaimer ................................................................................................................................. 2

Questions or Service Assistance ................................................................................................ 2

Product Identification Information ...............................................................................................2

Note Explanations ...................................................................................................................... 5

Scope of Manual ........................................................................................................................5

Product Unpacking and Inspection............................................................................................. 5

License Requirements ............................................................................................................... 5

Badger®ORION®Integral Transmitter/Hardcase Gas Meter Identification .................................. 6

Installation Tools and Materials .................................................................................................. 6

Label Information ........................................................................................................................6

Installation of Badger ORION Integral Transmitter...................................................................... 6

American®Commercial Diaphragm with Wire Seal Security Screw and Dial Index..............7

Badger ORION Model 64989-002 ............................................................................................ 7

Index and Index Cover Plate Removal from American Meter ..................................................... 7

Badger ORION Transmitter Label .............................................................................................. 8

Install Badger ORION Transmitter and American Cover Plate ................................................... 8

Program the Badger ORION Transmitter ....................................................................................9

Complete the Installation ..........................................................................................................10

AMERICAN®Commercial Diaphragm with Red Security Seals and Dial Index .................. 11

Badger ORION Model 64989-002 ...........................................................................................11

Index and Index Cover Plate Removal From American Meter ..................................................11

Badger ORION Transmitter Label ............................................................................................12

Install the Badger ORION Transmitter and American Cover Plate ........................................... 12

Program the Badger ORION Transmitter ..................................................................................13

Complete the Installation ..........................................................................................................14

(Thispage intentionallyleftblank)

License Requirements

This device complies with Part 15 of FCC

Rules. Operation of this device is subject to

the following conditions: (1) This device may

not cause harmful interference, and (2) this

device must accept any interference received,

including interference that may cause

undesired operation.

No FCC license is required by a utility to

operate a Badger ORION meter reading

system.

Any changes made, but not approved by

Badger Meter, can void the user’s authority to

operate the equipment.

Note Explanations

NOTE:

Communicates installation, operation, or

maintenance information that is safety related but

not hazard related.

Scope of Manual

This manual contains installation instructions

for mounting the Badger®ORION®Integral

Transmitter for Gas Meters on two American

Gas Meters.

Proper performance and reliability of the

Badger ORION system depends upon

installation in accordance with these

instructions.

Product Unpacking and Inspection

Upon receipt of the product, perform the

following unpacking and inspection

procedures:

NOTE:

If damage to the shipping container is

evident upon receipt, request the carrier to be

present when the product is unpacked.

Carefully open the shipping package, follow

any instructions that may be marked on the

exterior. Remove all cushioning material

surrounding the product and carefully lift the

product from the package.

Retain the package and all packing material

for possible use in reshipment or storage.

Visually inspect the product and applicable

accessories for any physical damage such as

scratches, loose or broken parts, or any other

sign of damage that may have occurred

during shipment.

NOTE:

If damage is found, request an inspection

by the carrier’s agent within 48 hours of delivery

and file a claim with the carrier. A claim for

equipment damage in transit is the sole

responsibility of the purchaser.

Badger®ORION®Integral Transmitter/Hardcase Gas Meter Identification

Badger ORION integral transmitters for gas meters are designed for use with only two major

brands of hardcase gas meters. Please refer to and use the following identification table.

Installation of Badger ORION Integral Transmitter

This manual describes two types of installation of the Badger ORION transmitter and American

index on an American gas meter.

The first section of this manual describes the installation on an American Commercial Diaphragm

and Turbine Meter with Wire Seal Security Screws.

The second section of this manual describes the installation on an American Commercial

Diaphragm and Turbine Meter with Red Security Seals.

Identification Table

American Badger ORION

Gas Meter Manufacturer Gas Meter Models Transmitter Number

American®Meter AL-800, AL-1000, AL-1400, 64989-002

AL-2300, AL-5000 and

GTS/GTX Turbine Meters

Installation Tools and Materials

Use magnetized screwdrivers.

1/4" flat screwdriver

3/16" flat screwdriver

Radix®Handheld

Label Information

Certification markings are noted on the product label.

ORION Transmitter

2 Seal Caps

2 Small

Tamper Plugs

2 Large

Tamper Plugs

2 Washers

4 Screws

NOTE: The screws provided in this installation kit

are not drilled for wire seals. Therefore, the wire

seal is replaced with plastic seal cups provided in

the kit.

Index and Index Cover Plate Removal from

American Meter with Seal Security Screw

Step 1: Remove the wire security seal from

the index cover mounting screw.

Step 2: Use a large screwdriver to remove

the four (4) 18-8 index cover mounting plate

screws and American Index. Discard the four

screws.

Step 3: Remove the American index and

mounting plate.

ORION Model 64989-002 Transmitter Kit for

American Commercial Diaphragm and Turbine

Meter with Wire Seal Security Screw

AMERICAN®Commercial Diaphragm and Turbine Meters

with Wire Seal Security Screw

American Commercial Diaphragm and Turbine

Meter with Wire Seal Security Screw

When attaching an Badger ORION transmitter

to a gas meter make sure it mounts securely

to the meter.

Install the Badger ORION Transmitter and

American Cover Plate

Use care when handling the Badger ORION

transmitter to insure the drive pawl is not

subjected to any physical abuse. Abuse may

cause this spindle to become bent,

misaligned, or otherwise inoperative.

Step 1: Place the Badger ORION transmitter

on top of the gas meter, where the index and

index cover plate were previously removed.

Place the transmitter drive pawl so it is

perpendicular to the meter drive pawl.

Step B: Place a new serial number tag above

the one that is on the transmitter.

Step C: Place the cover plate back on the

transmitter.

Badger®ORION®Transmitter Label

If the utility chooses to add an additional

label, follow steps A, B, and C below. If not,

go to Install in the next column.

Serial Number

Label

Step A: With a needle nose pliers pull the

plastic cover plate down and off.

Drive Pawl

Spindle

Step 2: When mounting a Badger ORION

transmitter to a gas meter, make sure the

transmitter drive pawl engages the gas meter

drive pawl. These two drive pawls must mate

without causing any binding or potential for

disengagement.

Test to ensure the pawls are engaged and

moving freely.

Meter Drive

Pawl

Transmitter

Drive Pawl

placing transmitter on

meter incorrectly may

damage the output seal of

the gas meter.

Step 3: Be sure the gas INLET markings are

on the same side of the meter and the lens

faces forward.

Gas INLET

markings

Lens facing

forward

Step 4: Place the American Index and cover

plate (removed earlier) back on the Badger®

ORION®transmitter.

Place it so the text;

TURBINE FRONT FLOW

AL-600, AL-1000, AL-1400, AL-2300, and

AL-5000

(or other such text); faces the front

and the index hole is centered around the

transmitter drive pawl.

Place the index drive

pawl perpendicular to

the transmitter drive

pawl.

Step 5: Place two screws, with a washer on

each, into two corners of the cover mounting

plate.

Use four (4) 18-18x3-1/2 supplied mounting

screws to attach the index, cover plate, and

Badger ORION transmitter to the gas meter.

Washer

Step 7: Tighten all screws evenly with a large

screwdriver to approximately 70 inch lbs.

Step 6: Index and cover has two platic seal

caps that are difficult to maneuver around with

the long bolts. Place two of the screws,

without washers, through the white seal caps.

Place them in the other opposite corners of

the cover mounting plate.

Program the Badger ORION Transmitter

Badger uses the Radix®system to display

and process screens.

Place the Radix so the optic read head aligns

with the LED output port. The angle of

approach should be about 30 degrees.

Rotate Radix unit to

about 30 degrees

Radix

30°

This completes the installation of a Badger®

ORION®transmitter on an American®

Commercial Diaphragm and Turbine Meter

with Wire Seal Security Screw converted to

seal caps.

If the index mounting seal caps were

removed, replace them with the extra caps

provided in the installation kit.

Complete the Installation

After programming, add seal caps to the front

and rear screws of the index cover plate. Only

the front screw is shown below.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Badger Meter

Badger Meter

Badger Meter ModMAG M1000 Manual de usuario

Badger Meter

Badger Meter Dynasonics TFX-5000 Manual de usuario

Badger Meter

Badger Meter Recordall RTR Orion 3-Wire Guía de instalación y uso

Badger Meter

Badger Meter Primo Advanced BMAG-350-icpf Manual

Badger Meter

Badger Meter ORION SE Guía de instalación y uso

Badger Meter

Badger Meter 6200 Manual de usuario

Badger Meter

Badger Meter ILR710 Manual del propietario

Badger Meter

Badger Meter IOG Series Manual de usuario

Badger Meter

Badger Meter ModMAG M2000 Manual de usuario

Badger Meter

Badger Meter FC-5000 Manual de usuario

Badger Meter

Badger Meter LM-OG-P2 Advanced Manual de usuario

Badger Meter

Badger Meter BadgerTouch HREBT Manual de usuario

Badger Meter

Badger Meter FMS-3 Manual de usuario

Badger Meter

Badger Meter PortaSonic 9000 Manual de usuario

Badger Meter

Badger Meter ModMAG M2000 Instrucciones de funcionamiento

Badger Meter

Badger Meter Impeller Data Industrial 228PV Series Manual de usuario

Badger Meter

Badger Meter Recordall Disc Series Manual de usuario

Badger Meter

Badger Meter Hedland EZ-View H915 Manual de usuario

Badger Meter

Badger Meter ModMAG M1000 Manual de usuario

Badger Meter

Badger Meter ER-9 Manual de usuario

Badger Meter

Badger Meter Dynasonics DXN Manual de usuario

Badger Meter

Badger Meter 380CS Manual de usuario

Badger Meter

Badger Meter M-series Manual de usuario

Badger Meter

Badger Meter Dynasonics UHC100 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario