Bacharach 19-8104 Guía de solución de problemas

Monoxor

®III

Carbon Monoxide Analyzer

Instruction 19-9326

Operation & Maintenance

Rev. 2 – October 2003

Product Leadership • Training • Service • Reliability

WARRANTY

Bacharach, Inc. warrants to Buyer that at the time of delivery this Product will be free from defects in material

and manufature and will onform substantially to Baharah In.’s aliable seiations. Baharah’s

liability and Buyer’s remedy under this warranty are limited to the repair or replacement, at Bacharach’s option,

of this Product or parts thereof returned to Seller at the factory of manufacture and shown to Bacharach Inc.’s

reasonable satisfaction to have been defective; provided that written notice of the defect shall have been given

by Buyer to Bacharach Inc. within two (2) years after the date of delivery of this Product by Bacharach, Inc.

Bacharach, Inc. warrants to Buyer that it will convey good title to this Product. Bacharach’s liability and Buyer’s

remedy under this warranty of title are limited to the removal of any title defects or, at the election of Bacharach,

to the replacement of this Product or parts thereof that are defective in title.

THE FOREGOING WARRANTIES ARE EXCLUSIVE AND ARE GIVEN AND ACCEPTED IN LIEU OF (I) ANY

AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IM-

PLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE: AND (II) ANY

OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR TORT, WHETHER OR NOT ARIS-

ING FROM BACHARACH’S NEGLIGENCE, ACTUAL OR IMPLIED. The remedies of the Buyer shall be limited

to those provided herein to the exclusion of any and all other remedies including, without limitation incidental or

consequential damages. No agreement varying or extending the foregoing warranties, remedies or this limita-

tion will be binding uon Baharah, In. unless in writing, signed by a duly authorized ofer of Baharah.

www.bacharach-inc.com

Notice:

Produt imrovements and enhanements are ontinuous, therefore the seiations and information on-

tained in this document may change without notice.

Bacharach, Inc. shall not be liable for errors contained herein or for incidental or consequential damages in con-

nection with the furnishing, performance, or use of this material.

No part of this document may be photocopied, reproduced, or translated to another language without the prior

written consent of Bacharach, Inc.

BACHARACH and Monoxor are registered trademarks of Bacharach, Inc. All other trademarks,

trade names, service marks and logos referenced herein belong to their respective companies.

Declaration of Conformity

Manufacturer’s name: Bacharach, Inc.

Manufacturer’ address: 621 Hunt Valley Circle

New Kensington, PA 15068

European Operations: Bacharach Europe

Sovereign House, Queensway

Royal Leamington Spa

Warwickshire CV31 3JR

United Kingdom

Product name: Monoxor III

onforms to the following seiations:

European Directive 89/336/EEC

EN50082-1: 1997 (Electrostatic Discharge)

EN50082-1: 1997 (Immunity)

EN55022; Group 1, Class B (Emission)

Instruction 19-9326

Monoxor III

Instruction 19-9326 i

Contents

1.0 INTRODUCTION ..................................................................................1

2.0 TECHNICAL CHARACTERISTICS...................................................3

3.0 PREPARING THE ANALYZER FOR OPERATION.......................5

3.1 Battery Installation .........................................................................5

3.2 Probe Installation ............................................................................6

3.3 Front Panel Pushbuttons.................................................................7

3.4 Setup Mode.......................................................................................8

3.4.1 Entering Setup ......................................................................8

3.4.2 Temperature Units Setup .....................................................8

3.4.3 CO Channel Zero Setup ........................................................9

3.4.4 Time Setup...........................................................................10

3.4.5 Date Setup ...........................................................................10

3.4.6 Year Setup ...........................................................................11

3.4.7 Selecting Printer Protocol ...................................................11

3.4.8 Exiting the Setup Screen ....................................................11

4.0 OPERATION ........................................................................................13

4.1 Taking a Gas Sample.....................................................................13

4.2 Ending a Test .................................................................................14

4.3 Turning OFF the Analyzer............................................................14

4.4 CO Purge During Turn OFF .........................................................14

4.5 CO Sensor Error Screen ................................................................15

4.6 Using the Backlight .......................................................................15

4.7 Using the Probe..............................................................................15

4.8 Operating Tips ...............................................................................16

4.9 Resetting the Microprocessor ........................................................16

4.10 Printing Test Results...................................................................17

5.0 CALIBRATION & MAINTENANCE ................................................19

5.1 Entering the Calibration Mode and Testing the Display Segments...19

5.2 Ambient Temperature Calibration ...............................................20

5.3 CO Sensor Zero & Calibration.......................................................20

5.4 Water Trap / Filter Maintenance..................................................22

5.5 CO Sensor Replacement ................................................................23

5.6 Pump Assembly Replacement .......................................................24

6.0 PARTS & SERVICE............................................................................27

6.1 Replacement Parts.........................................................................27

6.2 Accessories......................................................................................27

6.3 Service Centers ..............................................................................28

7.0 HAZARDS OF CARBON MONOXIDE.............................................29

Monoxor III

Instruction 19-9326

Notes

Instruction 19-9326 1

Monoxor III

1.0 INTRODUCTION

The Monoxor III is a portable analyzer designed to detect and display

concentrations of Carbon Monoxide (CO) gas between 0 and 2000 ppm. The

analyzer is capable of testing for CO in both ambient room air, and in the

ue-gas stream of fossil-fuel red furnaces and boilers.

Ordering Information:

Part No. Description

19-8104 Monoxor III, includes 4 ‘AA’ batteries, probe & hose assembly

with integral water-trap / lter, and a hard carrying case

19-8105 Monoxor III, includes 4 ‘AA’ batteries, probe & hose assembly

with integral water-trap / lter, hard carrying case, plus

an IrDA printer with an assortment of printer accessories

including an AC adapter, roll of paper, in-car charger, belt

clip, and magnet

The analyzer detects and displays the presence of CO by rst drawing in a

gas sample from the area being tested by the analyzer’s built-in motorized

pump. The gas sample is next directed into a sensor chamber where the

sample is analyzed for the presence of CO. If CO is detected, the CO ppm

level is displayed on the analyzer’s LCD.

A permanent record of the detected CO level, along with the current time

and date, can be made by using the optional wireless IrDA printer.

A backlight enables the operator to read the display in dimly-lit areas. A

power-saver feature causes the backlight to automatically turn OFF after

10 minutes, and causes the analyzer to shut OFF after 20 minutes of inac-

tivity. The power saver feature, however, is disabled while the detected CO

level is above 50 ppm.

When the analyzer is used to measure the CO content in ue-gas, a rigid

stainless steel probe with handle is provided that allows gas samples to

be taken from within the ue stack. An integral water-trap / lter pre-

vents water and soot from being drawn into the analyzer. The probe can

also be used in ambient testing to draw in gas samples from cramped and

conned areas.

If the analyzer is turned OFF while a high level of CO is still present

within the unit, the analyzer’s pump remains running and the unit will

not turn OFF until the detected CO level drops below 50 ppm.

Instruction 19-9326

Monoxor III

Notes

Instruction 19-9326 3

Monoxor III

2.0 TECHNICAL CHARACTERISTICS

CO Display Range ...................... 0–2000 ppm

Accuracy ..................................... ±5% of reading or ±10 ppm,

whichever is greater*

Resolution ................................... 1 ppm

Response Time ........................... 90% of nal value within 40 sec.

Battery Requirement ................. Four disposable ‘AA’ Alkaline batteries

Operating Time .......................... Up to 18 hours continuous (pump running

and backlight off)

Warm Up Time........................... 10 or 60 seconds (depending on CO

channel zero setup, refer to Page 9)

Display ........................................ 4 digit by 2 line, 7-segment Liquid Crystal

Display

Front Panel Controls.................. Six push button switches

(refer to Section 3.3)

Operating Temperature:

Analyzer ................................. 32–104 °F (0–40 °C)

Probe....................................... 1000 °F (538 °C) max. at 5" insertion

Humidity..................................... 15 to 90% RH (non-condensing)

Printer Port ................................ IrDA or HP protocol

Weight ......................................... 16 oz with batteries

Size.............................................. 7.5"H x 3.1"W x 2.1"D (190x79x53 mm)

* Tighter accuracy in the lower ranges, up to ±2 ppm, may be attained if a

lower range calibration gas (e.g. 100 ppm CO) is used.

Instruction 19-9326

Monoxor III

Notes

Instruction 19-9326 5

Monoxor III

3.0 PREPARING THE ANALYZER

FOR OPERATION

To prepare a new analyzer for operation, you must install four ‘AA’

Alkaline batteries, install the probe (if needed), and set the correct time

and date as described in the following paragraphs.

For your convenience, and to ensure that the analyzer will provide reliable

CO readings, the CO sensor was installed and the analyzer calibrated on

500 ppm CO at the factory.

3.1 Battery Installation

Install fresh batteries as described below. Check the analyzer for sufcient

charge prior to each use. Replace the batteries if the low-battery symbol

appears in the lower right corner of the LCD. To install batteries:

1. Remove battery cover from back of unit (see Figure 3-1).

2. If old batteries are installed, remove and properly dispose of the

batteries.

3. Observing the polarity markings inside the battery compartment,

install four ‘AA’ Alkaline batteries.

4. Replace battery cover.

Figure 3-1. Battery Installation

          

          

               

                

           

Instruction 19-9326

Monoxor III

3.2 Probe Installation

Install the probe if the analyzer is going to be used for ue-gas CO mea-

surements, or if gas measurements need to be taken from a cramped or

conned area.

To install the probe, simply slide its hose over the GAS inlet of the ana-

lyzer (see Figure 3-2).

Figure 3-2. Probe Connection

      

   

         

            

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Bacharach

Bacharach

Bacharach Neutronics Mini-ICS Manual de usuario

Bacharach

Bacharach Fyrite Tech 50 Manual de operación y mantenimiento

Bacharach

Bacharach MANOMETER GAS PRESSURE GAUGE Manual de usuario

Bacharach

Bacharach Portable Combustion Analyzer Manual de usuario

Bacharach

Bacharach Neutronics LEGEND ID RI-2018 Series Manual de usuario

Bacharach

Bacharach Parasense 3300RM2 Manual

Bacharach

Bacharach PCA 400 Manual de usuario

Bacharach

Bacharach MGS-401 Manual de usuario

Bacharach

Bacharach Neutronics 7100P Manual de usuario

Bacharach

Bacharach AGM300 Manual de usuario

Bacharach

Bacharach Legend Series Manual de usuario

Bacharach

Bacharach Comfort Chek 400 Manual de usuario

Bacharach

Bacharach Snifit 40 Manual de usuario

Bacharach

Bacharach HGM-MZ Manual de usuario

Bacharach

Bacharach SF6 Portable Monitor Manual de usuario

Bacharach

Bacharach 2810 Guía de solución de problemas

Bacharach

Bacharach PCA 2 Manual de lista de piezas

Bacharach

Bacharach Fyrite INSIGHT PLUS Manual de usuario

Bacharach

Bacharach HI FLOW Sampler Manual de usuario

Bacharach

Bacharach LS-20B Manual de usuario

Bacharach

Bacharach Fyrite INSIGHT PLUS Manual de usuario

Bacharach

Bacharach 24-7224 Manual de usuario

Bacharach

Bacharach HGM-MZ Manual de usuario

Bacharach

Bacharach MGC100 Manual de operación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario